Here we report on the hybrid nanostructures where a single ZnS nanobelt was half‐covered with an aluminum (Al) film, which is an ideal platform for studying the second‐harmonic generation (SHG) enhancement effects of the Al coating. It was fabricated by the lift‐off process and allowed for the accurate comparison of the SHG intensity between the Al‐covered and the same bare ZnS nanobelt under consistent test conditions. The results indicate that the Al coating in the hybrid nanostructures not only confines the pumping laser in the ZnS effectively, but also concentrates the emitted SHG signal greatly, increasing the signal collection efficiency. By the combination of these two effects, ∼60 times enhancement of the SHG intensity is achieved at the optimized geometry size (width and thickness) of the ZnS nanobelts. The Al‐based hybrid nanostructures open up new possibilities for low‐cost, highly efficient and directional coherent nanolight sources at short wavelengths.
A mid‐infrared (MIR) supercontinuum (SC) has been demonstrated in a low‐loss telluride glass fiber. The double‐cladding fiber, fabricated using a novel extrusion method, exhibits excellent transmission at 8–14 μm: < 10 dB/m in the range of 8–13.5 μm and 6 dB/m at 11 μm. Launched intense ultrashort pulsed with a central wavelength of 7 μm, the step‐index fiber generates a MIR SC spanning from ∼2.0 μm to 16 μm, for a 40‐dB spectral flatness. This is a fresh experimental demonstration to reveal that telluride glass fiber can emit across the all MIR molecular fingerprint region, which is of key importance for applications such as diagnostics, gas sensing, and greenhouse CO2 detection.
A novel scheme to multiply the repetition rate of a monolithic self‐mode‐locked laser for generating sub‐terahertz pulse sources is successfully demonstrated. A coated Yb:KGW crystal is designed to achieve a self‐mode‐locked operation at a repetition rate of 24 GHz with an average output power exceeding 1.0 W at a pump power of 4.8 W. A partially reflective mirror is utilized to combine with the output surface of the gain medium to constitute an external Fabry‐Perot cavity. It is theoretically and experimentally verified that adjusting the external cavity length to satisfy the commensurate condition can lead to the frequency spacing to be various order harmonics of the mode spacing of the monolithic cavity. The maximum pulse repetition rate of the laser output can be up to 216 GHz and the pulse duration is as short as 330 fs. More importantly, the overall characteristics of the first‐order temporal autocorrelation traces obtained by sequentially scanning the external cavity.length display an intriguing phenomenon of temporally fractional revivals, similar to the feature of spatial Talbot revivals.
The generation of sub‐optical‐cycle, carrier–envelope phase‐stable light pulses is one of the frontiers of ultrafast optics. The two key ingredients for sub‐cycle pulse generation are bandwidths substantially exceeding one octave and accurate control of the spectral phase. These requirements are very challenging to satisfy with a single laser beam, and thus intense research activity is currently devoted to the coherent synthesis of pulses generated by separate sources. In this review we discuss the conceptual schemes and experimental tools that can be employed for the generation, amplification, control, and combination of separate light pulses. The main techniques for the spectrotemporal characterization of the synthesized fields are also described. We discuss recent implementations of coherent waveform synthesis: from the first demonstration of a single‐cycle optical pulse by the addition of two pulse trains derived from a fiber laser, to the coherent combination of the outputs from optical parametric chirped‐pulse amplifiers.
This article presents a novel III‐V on silicon laser. This work exploits the phenomenon that a passive silicon cavity, side‐coupled to a III‐V waveguide, will provide high and narrow‐band reflectivity into the III‐V waveguide: the resonant mirror. This results in an electrically pumped laser with a threshold current of 4 mA and a side‐mode suppression ratio up to 48 dB.
Light manipulation is paramountly important to the fabrication of high‐performance optoelectronic devices such as solar cells and photodetectors. In this study, a high‐performance near‐infrared light nanophotodetector (NIRPD) was fabricated based on a germanium nanoneedles array (GeNNs array) with strong light confining capability, and single‐layer graphene (SLG) modified with heavily doped indium tin oxide nanoparticles (ITONPs), which were capable of inducing localized surface plasmon resonance (LSPR) under NIR irradiation. An optoelectronic study shows that after modification with ITONPs the device performance including photocurrent, responsivity and detectivity was considerably improved. In addition, the ITONPs@SLG/GeNNs array NIRPD was able to monitor fast‐switching optical signals, the frequency was as high as 1 MHz, with very fast response rates. Theoretical simulations based on finite‐element method (FEM) revealed that the observed high performance was not only due to the strong light‐confining capability of the GeNNs array, but also due to the plasmonic ITONPs‐induced hot electron injection. The above results suggest that the present NIRPD will have great potential in future optoelectronic devices application.
This work proves the feasibility of a novel concept of differential absorption lidar based on the Scheimpflug principle. The range‐resolved atmospheric backscattering signal of a laser beam is retrieved by employing a tilted linear sensor with a Newtonian telescope, satisfying the Scheimpflug condition. Infinite focus depth is achieved despite employing a large optical aperture. The concept is demonstrated by measuring the range‐resolved atmospheric oxygen concentration with a tunable continuous‐wave narrow‐band laser diode emitting around 761 nm over a path of one kilometer during night time. Laser power requirements for daytime operation are also investigated and validated with single‐band atmospheric aerosol measurements by employing a broad‐band 3.2‐W laser diode. The results presented in this work show the potential of employing the continuous‐wave differential absorption lidar (CW‐DIAL) technique for remote profiling of atmospheric gases in daytime if high‐power narrow‐band continuous‐wave light sources were to be employed.
Optically levitated nanodiamonds with nitrogen‐vacancy centers promise a high‐quality hybrid spin‐optomechanical system. However, the trapped nanodiamond absorbs energy from laser beams and causes thermal damage in vacuum. It is proposed here to solve the problem by trapping a composite particle (a nanodiamond core coated with a less absorptive silica shell) at the center of strongly focused doughnut‐shaped laser beams. Systematical study on the trapping stability, heat absorption, and oscillation frequency concludes that the azimuthally polarized Gaussian beam and the linearly polarized Laguerre‐Gaussian beam LG03 are the optimal choices. With our proposal, particles with strong absorption coefficients can be trapped without obvious heating and, thus, the spin‐optomechanical system based on levitated nanodiamonds are made possible in high vacuum with the present experimental techniques.
Dewetting of thin metal films is one of the most widespread method for functional plasmonic nanostructures fabrication. However, simple thermal‐induced dewetting does not allow to control degree of nanostructures order without additional lithographic process steps. Here we propose a novel method for lithography‐free and large‐scale fabrication of plasmonic nanostructures via controllable femtosecond laser‐induced dewetting. The method is based on femtosecond laser surface pattering of a thin film followed by a nanoscale hydrodynamical instability, which is found to be very controllable under specific irradiation conditions. We achieve control over degree of nanostructures order by changing laser irradiation parametrs and film thickness. This allowed us to exploit the method for the broad range of applications: resonant light absorbtion and scattering, sensing, and potential improving of thin‐film solar cells.
The progress on multi‐wavelength quantum cascade laser arrays in the mid‐infrared is reviewed, which are a powerful, robust and versatile source for next‐generation spectroscopy and stand‐off detection systems. Various approaches for the array elements are discussed, from conventional distributed‐feedback lasers over master‐oscillator power‐amplifier devices to tapered oscillators, and the performances of the different array types are compared. The challenges associated with reliably achieving single‐mode operation at deterministic wavelengths for each laser element in combination with a uniform distribution of high output power across the array are discussed. An overview of the range of applications benefiting from the quantum cascade laser approach is given. The distinct and crucial advantages of arrays over external cavity quantum cascade lasers as tunable single‐mode sources in the mid‐infrared are discussed. Spectroscopy and hyperspectral imaging demonstrations by quantum cascade laser arrays are reviewed.
III‐nitride light‐emitting diodes (LEDs) and laser diodes (LDs) are ultimately limited in performance due to parasitic Auger recombination. For LEDs, the consequences are poor efficiencies at high current densities; for LDs, the consequences are high thresholds and limited efficiencies. Here, we present arguments for III‐nitride quantum dots (QDs) as active regions for both LEDs and LDs, to circumvent Auger recombination and achieve efficiencies at higher current densities that are not possible with quantum wells. QD‐based LDs achieve gain and thresholds at lower carrier densities before Auger recombination becomes appreciable. QD‐based LEDs achieve higher efficiencies at higher currents because of higher spontaneous emission rates and reduced Auger recombination. The technical challenge is to control the size distribution and volume of the QDs to realize these benefits. If constructed properly, III‐nitride light‐emitting devices with QD active regions have the potential to outperform quantum well light‐emitting devices, and enable an era of ultra‐efficient solid‐state lighting.
High efficiency, broad bandwidth, and robust angular tolerance are key considerations in photonic device design. Here, a few‐layer, asymmetric light transmitting metasurface that simultaneously satisfies all the above requirements is reported. The metasurface consists of coupled metallic sheets. It has a measured transmission efficiency of 80%, extinction ratio of 13.8 dB around 1.5 μm, and a full width half maximum bandwidth of 1.7 μm. It is as thin as 290 nm, has good performance tolerance against the angle of incidence and constituent nano‐structure geometry variations. This work demonstrates a practical asymmetric light transmission device with optimal performance for large scale manufacturing.
Stimulated emission depletion (STED) microscopy has become a powerful imaging and localized excitation method, breaking the diffraction barrier for improved spatial resolution in cellular imaging, lithography, etc. Because of specimen‐induced aberrations and scattering distortion, it is a great challenge for STED to maintain consistent lateral resolution deep inside specimens. Here we report on deep imaging STED microscopy using a Gaussian beam for excitation and a hollow Bessel beam for depletion (GB‐STED). The proposed scheme shows an improved imaging depth of up to about 155 μm in a solid agarose sample, 115 μm in polydimethylsiloxane, and 100 μm in a phantom of gray matter in brain tissue with consistent super resolution, while standard STED microscopy shows a significantly reduced lateral resolution at the same imaging depth. The results indicate the excellent imaging penetration capability of GB‐STED, paving the way for deep tissue super‐resolution imaging and three‐dimensional precise laser fabrication.
We experimentally demonstrate an optically‐pumped III‐V/Si vertical‐cavity laser with lateral emission into a silicon waveguide. This on‐chip hybrid laser comprises a distributed Bragg reflector, a III‐V active layer, and a high‐contrast grating reflector, which simultaneously funnels light into the waveguide integrated with the laser. This laser has the advantages of long‐wavelength vertical‐cavity surface‐emitting lasers, such as low threshold and high side‐mode suppression ratio, while allowing integration with silicon photonic circuits, and is fabricated using CMOS compatible processes. It has the potential for ultrahigh‐speed operation beyond 100 Gbit/s and features a novel mechanism for transverse mode control.
In the development of microfluidic chips, conventional 2D processing technologies contribute to the manufacturing of basic microchannel networks. Nevertheless, in the pursuit of versatile microfluidic chips, flexible integration of multifunctional components within a tiny chip is still challenging because a chip containing micro‐channels is a non‐flat substrate. Recently, on‐chip laser processing (OCLP) technology has emerged as an appealing alternative to achieve chip functionalization through in situ fabrication of 3D microstructures. Here, the recent development of OCLP‐enabled multifunctional microfluidic chips, including several accessible photochemical/photophysical schemes, and photosensitive materials permiting OCLP, is reviewed. To demonstrate the capability of OCLP technology, a series of typical micro‐components fabricated using OCLP are introduced. The prospects and current challenges of this field are discussed.
Nonlinear wave mixing in mesoscopic silicon structures is a fundamental nonlinear process with broad impact and applications. Silicon nanowire waveguides, in particular, have large third‐order Kerr nonlinearity, enabling salient and abundant four‐wave‐mixing dynamics and functionalities. Besides the Kerr effect, in silicon waveguides two‐photon absorption generates high free‐carrier densities, with corresponding fifth‐order nonlinearity in the forms of free‐carrier dispersion and free‐carrier absorption. However, whether these fifth‐order free‐carrier nonlinear effects can lead to six‐wave‐mixing dynamics still remains an open question until now. Here we report the demonstration of free‐carrier‐induced six‐wave mixing in silicon nanowires. Unique features, including inverse detuning dependence of six‐wave‐mixing efficiency and its higher sensitivity to pump power, are originally observed and verified by analytical prediction and numerical modeling. Additionally, asymmetric sideband generation is observed for different laser detunings, resulting from the phase‐sensitive interactions between free‐carrier six‐wave‐mixing and Kerr four‐wave‐mixing dynamics. These discoveries provide a new path for nonlinear multi‐wave interactions in nanoscale platforms.
Narrow‐linewidth lasers are key elements in optical metrology and spectroscopy. Spectral purity of these lasers determines accuracy of the measurements and quality of collected data. Solid state and fiber lasers are stabilized to relatively large and complex external optical cavities or narrow atomic and molecular transitions to improve their spectral purity. While this stabilization technique is rather generic, its complexity increases tremendously moving to longer wavelenghts, to the infrared (IR) range. Inherent increase of losses of optical materials at longer wavelengths hinders realization of compact, room temperature, high finesse IR cavities suitable for laser stabilization. In this paper, we report on demonstration of quantum cascade lasers stabilized to high‐Q crystalline mid‐IR microcavities. The lasers operating at room temperature in the 4.3‐4.6 μm region have a linewidth approaching 10 kHz and are promising for on‐chip mid‐IR and IR spectrometers.
Inspired from butterfly wings that exhibit unique dewetting properties and brilliant structural color synchronously, we reported here the preparation of biomimetic few‐layer graphene films through a template‐directed chemical vapor deposition method using laser‐structured Cu foil as substrates. Hierarchical micronanostructures, including microscale stripes derived from the laser scanning and nanoscale laser‐induced periodic surface structures (LIPSS), formed on Cu foil after a simple femtosecond laser treatment. By tuning the laser power, the surface roughness of the resultant Cu foils can be well controlled. Using the laser structures Cu foil as templates, biomimetic few‐layer graphene films with both iridescence and superhydrophobicity have been successfully prepared. The present work may open up a new way to design and prepare structured graphene film in a biomimetic manner, and we deem that the bioinspired few‐layer graphene films may find broad applications in the near future.
