舵几何特征对桨-舵系统尾流场演化的影响

发生在桨和舵之间的干扰会影响螺旋桨尾流的演化,导致尾流场中的湍流在下游增强,恶化船舶的振动和噪声性能,深入分析舵几何参数对桨-舵系统尾流场演化的影响能够为推进器尾流场的调节和减振降噪提供新思路.因此,从弦长、剖面和梯形舵入手分析不同的舵几何参数对螺旋桨尾流场演化特性的影响,使用大漩涡模拟方法模拟流场中的湍流结构,对不同舵弦长、剖面下的螺旋桨尾涡结构演化进行了分析,在舵弦长、剖面影响螺旋桨尾流场演化的研究的基础上分析了梯形舵对螺旋桨尾涡结构的影响,进一步分析了梯形舵影响下的螺旋桨尾流场中湍动能的分布.结果表明舵的弦长和剖面均会影响螺旋桨尾流场的演化,这种影响表现为更大的弦长和更厚的剖面会促进螺旋桨梢涡在舵压力面上的偏移,更薄的舵剖面会带来更强烈的螺旋桨毂涡偏移;涡管轮廓和舵表面脉动压力的对比均表明梯形舵会促进螺旋桨尾流场沿逆舵梯度方向偏移,从而导致螺旋桨的尾涡结构在舵两侧及下游呈现不对称分布,桨-舵系统下游的湍流结构与螺旋桨尾涡-舵碰撞过程、螺旋桨尾涡-舵随边涡干扰过程、螺旋桨梢涡-螺旋桨毂涡干扰有关,偏移更大的螺旋桨尾涡结构会在尾流场中更早地引起湍动能增强.     

Application of a vortex lattice numerical model in the calculation of inviscid incompressible flow around delta wings

The flow over a flat plate delta wing at incidence and in sideslip is studied using vortex lattice models based on streamwise penelling. For the attached flow problem the effect of sideslip is simulated by modifying the standard vortex lattice model for zero sideslip by aligning the trailing vortices aft of the wing along the resultant flow direction. For the separated flow problem a non-linear vortex lattice model is developed for both zero and non-zero sideslip angles in which the shape and position of the leading edge separation vortices are calculated by an iterative procedure starting from an assumed initial shape. The theoretical values are compared with available theoretical and experimental results.     

Formation and evolution of vortex rings induced by interactions between shock waves and a low-density bubble

The deformation and instability of a low-density spherical bubble induced by an incident and its reflected shock waves are studied by using the large eddy simulation method. The computational model is firstly validated by experimental results from the literature and is further used to examine the effect of incident shock wave strength on the formations and three-dimensional evolutions of the vortex rings. For the weak shock wave case (Ma?=?1.24), the baroclinic effect induced by the reflected shock wave is the key mechanism for the formation of new vortex rings. The vortex rings not only move due to the self-induced effect and the flow field velocity, but also generate azimuthal instability due to the pressure disturbance. For the strong shock wave case (Ma?=?2.2), a boundary layer is formed adjacent to the end wall owing to the approach of vortex ring, and unsteady separation of the boundary layer near the wall results in the ejection and formation of new vortex rings. These vortex rings interact in the vicinity of the end wall and finally collapse to a complicated vortex structure via azimuthal instability. For both shock wave strength cases, the evolutions of vortex rings due to the instability lead to the formation of the complicated structure dominated by the small-scale streamwise vortices.     

Numerical simulation on an interaction of a vortex street with an elliptical leading edge using an unstructured grid

An algorithm for a time accurate incompressible Navier–Stokes solver on an unstructured grid is presented. The algorithm uses a second order, three‐point, backward difference formula for the physical time marching. For each time step, a divergence free flow field is obtained based on an artificial compressibility method. An implicit method with a local time step is used to accelerate the convergence for the pseudotime iteration. To validate the code, an unsteady laminar flow over a circular cylinder at a Reynolds number of 200 is calculated. The results are compared with available experimental and numerical data and good agreements are achieved. Using the developed unsteady code, an interaction of a Karman vortex street with an elliptical leading edge is simulated. The incident Karman vortex street is generated by a circular cylinder located upstream. A clustering to the path of the vortices is achieved easily due to flexibility of an unstructured grid. Details of the interaction mechanism are analysed by investigating evolutions of vortices. Characteristics of the interactions are compared for large‐ and small‐scale vortex streets. Different patterns of the interaction are observed for those two vortex streets and the observation is in agreement with experiment. Copyright © 2004 John Wiley & Sons, Ltd.     

Elementary aspects of vortex motion

Several aspects of vortex motion are considered, with a special stress on the present status of idealization, such as point vortices or vortex filament. As an introduction, elements of vortices induced by the transient flow past an obstacle are considered and their role and development are stated.

Following this introduction, a general survey of the issues in this symposium is made sketchily. As an example, the motion of point vortices in the presence of an external flow or a boundary is discussed on the basis of the Hamiltonian formalism. The cases of linear flow and semicircular boundary are taken as examples of regular and chaotic motions. Secular behaviour of a pair of vortices in the flow is remarked.     

Combined action of transverse oscillations and uniform cross-flow on vortex formation and pattern of a circular cylinder

This paper attempts to study the roles of lateral cylinder oscillations and a uniform cross-flow in the vortex formation and wake modes of an oscillating circular cylinder. A circular cylinder is given lateral oscillations of varying amplitudes (between 0.28 and 1.42 cylinder-diameters) in a slow uniform flow stream (Reynolds number=284) to produce the 2S, 2P and P+S wake modes. Detailed flow information is obtained with time-resolved particle-image velocimetry and the phase-locked averaging techniques. In the 2S and 2P mode, the flow speeds relative to the cylinder movement are less than the uniform flow velocity and it is found that initial formation of a vortex is caused by shear-layer separation of the uniform flow on the cylinder. Subsequent development of the shear-layer vortices is affected by the lateral cylinder movement. At small cylinder oscillation amplitudes, vortices are shed in synchronization with the cylinder movement, resulting in the 2S mode. The 2P mode occurs at larger cylinder oscillation amplitudes at which each shear-layer vortex is found to undergo intense stretching and eventual bifurcation into two separate vortices. The P+S mode occurs when the cylinder moving speeds are, for most of the time, higher than the speed of the uniform flow. These situations are found at fast and large-amplitude cylinder oscillations in which the flow relative to the cylinder movement takes over the uniform flow in governing the initial vortex formation. The formation stages of vortices from the cylinder are found to bear close resemblance to those of a vortex street pattern of a cylinder oscillating in an otherwise quiescent fluid at Keulegan–Carpenter numbers around 16. Vortices in the inclined vortex street pattern so formed are then convected downstream by the uniform flow as the vortex pairs in the 2P mode.     

Nonlinear evolution of Görtler vortices in the near-wall part of a boundary layer

The evolution of Görtler vortices with wavelength smaller than the thickness of the boundary layer on a concave surface is modelled asymptotically at high Reynolds and Görtler numbers. It is known that in the initial linear stage of their evolution such vortices have the largest increment of amplitude growth. Numerical results demonstrate that taking the nonlinear interaction of the flow parameters into account considerably reduces the growth rate and leads to the forming of a perturbed vortex region core; profiles of the flow characteristics in the different stages of vortex evolution are presented.     

Stereoscopic PIV measurement of unsteady flows in an axial compressor stage

Stereoscopic particle-image velocimetry (SPIV) measurements are conducted in a Low-speed Large-scale Axial Compressor. During the experiment the two CCD cameras are placed at the different sides of the laser light sheet and it is proved that this configuration is more suitable for the investigation in multi-stage turbomachines. The measured results, including the overall performances of many typical flow structures near the rotor tip region and the phase locked unsteady flows inside the stator passage at both the design and near-stall conditions, are introduced. Some new features of the complicated flow structures, such as the breakdown of the tip leakage vortex, the formation of the compound corner vortex at the rotor suction tip corner, the interactions between the hub stall and the tip separation and the rotor wakes, and the evolutions of the tip corner anti-rotating streamwise vortices inside the stator passage, are revealed.     

Characterization of the PVC phenomena in the exhaust of a cyclone dust separator

A laboratory scale cyclone dust separator with swirl numbers varying from 3.043 to 1.790 was used to examine the effects of different downstream pipework configurations, flowrates and swirl numbers upon the size, shape, and position of the precessing vortex core. Also examined was the effect the precessing vortex core had on the reverse flow zone, and the relationship between the two. It was concluded that the reverse flow zone displaced the central vortex core to create the precessing vortex core. The reverse flow zone would then provide feedback for the precessing vortex core, and precess around the central axis about 30 degrees behind the precessing vortex core (P.V.C). The size and position of the P.V.C was effected by changes in Reynolds number, and any additions of downstream systems to the cyclone would also affect the strength of the P.V.C. The P.V.C would squeeze and accelerate the flow through a constriction set up between the outer limits of the core and of the exit diameter wall. Spiral engulfment vortices were produced on the outside of the flow and served as the initial entrainment mechanism for external flow. The authors wish to acknowledge the financial assistance provided by British Petroleum for this research. P. Yazdabadi acknowledges the award of a SERC Total Technology studentship.     

Evolution of vortex structure in boundary layer transition induced by roughness elements

The particle image velocimetry (PIV) and hydrogen-bubble visualization technique are used to investigate the flat-plate boundary layer transition induced by an array of roughness elements. The streamwise evolutions of the mean and fluctuation velocity are analyzed, and the critical Reynolds number Re _k,c is determined between 339 and 443 under current experimental setup. The hairpin vortices shed from supercritical roughness elements are visualized by swirling strength, in which two pairs of counter-rotating vortices can be observed: one vortex pair is the manifestation of the neck of the hairpin vortices shed from the top of the roughness; the other vortex pair, which originates from the lower part of the roughness, comes from the streamwise vortices that are constantly perturbed by the hairpin vortex shedding.     

Numerical simulation on evolution of subharmonic low-speed streaks in minimal channel turbulent flow

The evolution of low-speed streaks in the turbulent boundary layer of the minimum channel flow unit at a low Reynolds number is simulated by the direct numer- ical simulation （DNS） based on the standard Fourier-Chebyshev spectral method. The subharmonic sinuous （SS） mode for two spanwise-aligned low-speed streaks is excited by imposing the initial perturbations. The possibilities and the physical realities of the turbulent sustaining in the minimal channel unit are examined. Based on such a flow field environment, the evolution of the low-speed streaks during a cycle of turbulent sus- taining, including lift-up, oscillation, and breakdown, is investigated. The development of streamwise vortices and the dynamics of vortex structures are examined. The results show that the vortices generated from the same streak are staggered along the streamwise direction, while the vortices induced by different streaks tilt toward the normal direction due to the mutual induction effect. It is the spatial variations of the streamwise vortices that cause the lift-up of the streaks. By resolving the transport dynamics of enstrophy, the strength of the vortices is found to continuously grow in the logarithmic layer through the vortex stretching mechanism during the evolution of streaks. The enhancement of the vortices contributes to the spanwise oscillation and the following breakdown of the low-speed streaks.     

Temporal development of turbulent boundary layers with embedded streamwise vortices

The interaction of streamwise vortices with turbulent boundary layer has been investigated using large-eddy simulation. The initial conditions are a pair of counterrotating Oseen vortices with flow between them directed toward the wall (common-flow-down), superimposed on various instantaneous realizations of a turbulent boundary layer. The time development of the vortices and their interaction with the boundary layer are studied by integrating the filtered Navier-Stokes equations in time. The most important effects of the vortices on the boundary layer are the thinning of the boundary layer between vortices (downwash region) and the thickening of the boundary layer in the upwash region. The vortices first move toward the wall as a result of the self-induced velocity, and then apart from each other because of the image vortices due to the solid wall. The Reynolds stress profiles highlight the highly three-dimensional structure of the turbulent boundary layer modified by the vortices. The presence of significant turbulent activity near the vortex center and in the upwash region suggests that localized instability mechanisms in addition to the convection of turbulent energy by the secondary flow are responsible for this effect. High levels of turbulent kinetic energy and secondary stresses in the vicinity of the vortex center are also observed. The numerical results show good agreement with experimental results.This work was supported by the Office of Naval Research under Grant N00014-89-J-1638. Computer time was supplied by the San Diego Supercomputing Center.     

The merging of two co-rotating vortices: a numerical study

The merging of two-dimensional co-rotating vortices is analysed through direct numerical simulations at large Reynolds numbers. It is shown how the Reynolds number affects each of the three phases that characterise this phenomenon. In the first phase, we examine the merging onset and focus on its definition. During the second rapid phase, the contributions of various flow regions upon the dynamics of a vortex are quantitatively studied. These regions are respectively the companion vortex, the filaments and an intermediate zone between vortices and filaments. The third phase is interpreted in terms of an advection diffusion process. Finally the final profile and circulation of the merged vortex is determined: the two thirds of the total circulation of the two initial vortices is contained in the newly formed vortex.     

Three-dimensional instability analysis of boundary layers perturbed by streamwise vortices

A parametric study is presented for the incompressible, zero-pressure-gradient flat-plate boundary layer perturbed by streamwise vortices. The vortices are placed near the leading edge and model the vortices induced by miniature vortex generators (MVGs), which consist in a spanwise-periodic array of small winglet pairs. The introduction of MVGs has been experimentally proved to be a successful passive flow control strategy for delaying laminar-turbulent transition caused by Tollmien–Schlichting (TS) waves. The counter-rotating vortex pairs induce non-modal, transient growth that leads to a streaky boundary layer flow. The initial intensity of the vortices and their wall-normal distances to the plate wall are varied with the aim of finding the most effective location for streak generation and the effect on the instability characteristics of the perturbed flow. The study includes the solution of the three-dimensional, stationary, streaky boundary layer flows by using the boundary region equations, and the three-dimensional instability analysis of the resulting basic flows by using the plane-marching parabolized stability equations. Depending on the initial circulation and positioning of the vortices, planar TS waves are stabilized by the presence of the streaks, resulting in a reduction in the region of instability and shrink of the neutral stability curve. For a fixed maximum streak amplitude below the threshold for secondary instability (SI), the most effective wall-normal distance for the formation of the streaks is found to also offer the most stabilization of TS waves. By setting a maximum streak amplitude above the threshold for SI, sinuous shear layer modes become unstable, as well as another instability mode that is amplified in a narrow region near the vortex inlet position.     

Vortex intensification in convective cells

The intensification of single vortices in convective flows swirled by the Coriolis force is studied numerically. The initial disturbances, specified against the background of a steady cell, are coaxial with the cell flow and have various swirl directions, intensities, and dimensions. It is shown that the vortices are intensified no matter whether the direction of disturbing vortex rotation is co- or counter-directional with the Coriolis force. If the disturbance intensity is small as compared with that of the convective-cell flow, the growth of the azimuthal velocity circulation in the perturbing vortices depends linearly on their initial circulation. For such vortices, the energy increase is proportional to the characteristic vortex radius to the power –5/3.Translated from Izvestiya Rossiiskoi Academii Nauk, Mekhanika Zhidkosti i Gaza, No. 5, 2004, pp. 62–68. Original Russian Text Copyright © 2004 by Ivanov and Povarnitsyn.     

65°三角翼亚音速复杂流场计算和数据可视化

提出一种基于非结构混合网格和有限体积法的有效计算策略,对第二期国际涡流试验项目(second international vortex flow experiment,VFE-2)的尖前缘65°三角翼在马赫数0.4,迎角20.3°,雷诺数2×10~6条件下的亚音速复杂流场结构进行数值模拟,重点探讨了基于计算数据进行该类型复杂涡系干扰表面和空间流场关键特征提取和数据可视化问题.通过与相关试验类比,建立了与先进试验流动显示技术相比拟的定性和定量分析方法,为三角翼这类复杂流场结构的精细分析奠定了技术基础.采用上述方法,细致分析了亚音速三角翼的大迎角复杂旋涡流场结构,得到了与试验一致的结论.研究证实:在大迎角条件下,三角翼流动物理复杂,黏性效应耦合严重,只有通过N-S方程计算才能准确地捕捉主涡和二次涡的发展.     

Three-dimensional numerical simulation of a vortex ring impacting a bump

A vortex ring impinging on a three-dimensional bump is studied using large eddy simulation for a Reynolds number Re = 4 × 10⁴ based on the initial translation speed and diameter of the vortex ring. The effects of bump height on the vortical flow phenomena and the underlying physical mechanisms are investigated. Based on the analysis of the evolution of vortical structures, two typical kinds of vortical structures, i.e., the wrapping vortices and the hair-pin vortices, are identified and play an important role in the flow state evolution. The circulation of the primary vortex ring reasonably elucidates some typical phases of flow evolution. Furthermore, the mechanism of flow transition from laminar to turbulent state has been revealed based on analysis of turbulent kinetic energy.     

Vortex stretching in a laminar boundary layer flow

 A new technique to produce controlled stretched vortices is presented. The initial vorticity comes from a laminar boundary layer flow and the stretching is parallel to the initial vorticity. This low velocity flow enables direct observations of the formation and destabilization of vortices. Visualizations are combined with quasi-instantaneous measurements of a full velocity profile obtained with an ultra-sonic pulsed Doppler velocimeter. Several modes of destabilization are observed and include pairing of two vortices, hairpin deformation, and vortex breakdown into a coil shape. Received: 3 April 1996/ Accepted: 4 October 1996     

圆射流中拟序涡配对的数值模拟

用三维涡丝法结合涡丝的增加与合并技术,对不可压圆射流场,数值模拟了在扰动中加入次谐波后流场拟序涡的配对,配对情况与实验结果一致,通过对不同时刻涡量图的比较与分析,给出了次谐波初始强度对涡配对的影响,初始强度越大,涡配对出现越早,涡配对位置越往上游移动;同时还得到了基波与次谐波初始相位差和涡配对的关系,没有相位差时,次谐波增长最快,相位差增加时,涡配对的速度降低。说明控制次谐波的初始强度和基波与次谐波的相位差,能起到控制圆射流剪切层乃至控制整个射流场的目的。     

Vortices in time-periodic shear flow

Vortices emerging in geophysical turbulence may experience deformations due to the non-uniform ambient flow induced by neighbouring vortices. At first approximation this ambient flow is modeled by a linear shear flow. It is well known from previous studies that the vortex may be (partially) destructed through removal of weak vorticity at the vortex edge—a process referred to as ‘stripping’. While most previous studies considered a stationary external shear flow, we have examined the behaviour of the vortex embedded in a linear shear flow whose strength changes harmonically in time. Aspects of the vortex dynamics and the (chaotic) transport of tracers have been studied by both laboratory experiments and numerical simulations based on a simple kinematical model.