An automatic falling drop system based on multicommutation process for photometric chlorine determination in bleach

In this work an automatic photometric procedure for the determination of chlorine in bleach samples employing N,N′-diethyl-p-phenylenediamine (DPD) as chromogenic reagent is described. The procedure was based on a falling drop system where the analyte (Cl₂) was collected by a DPD solution drop (50 μL) after its delivery from the sample bulk that was previously acidified. The flow system was designed based on the multicommutation process assembling a set of three-way solenoid valves, which under microcomputer control afforded facilities to handle sample and reagent solution in order to control analyte delivering and solution drop generation. The analyte volatilization was improved by coupling online a little heating device. The detection system comprised a green LED (515 nm) and a phototransistor. Aiming to prove the usefulness of the proposed procedure a set of bleach samples was analyzed. Comparing the results with those obtained with reference method no significant difference at 95% confidence level was observed. Other profitable features such as a linear response ranging from 15 up to 100 mg L⁻¹ Cl₂ (R = 0.999); a detection limit of 4.5 mg L⁻¹ Cl₂ estimated based on the 3σ criterion; a relative standard deviation of 2.5% (n = 10) using a typical bleach sample containing 25.0 mg L⁻¹ Cl₂; a consumption of 55 μg of DPD per determination; and a analytical frequency of 20 determinations per hour were also achieved.     

Coupling of flow injection wetting-film extraction without segmentation and phase separation to flame atomic absorption spectrometry for the determination of trace copper in water samples

A flow injection wetting-film extraction system without segmentor and phase separator has been coupled to flame atomic absorption spectrometry for the determination of trace copper. Isobutyl methyl ketone (MIBK) was selected as coating solvent and 8-hydroxyquinoline (oxine) as the chelating reagent. By switching of a 8-channel valve and alternative initiation of two peristaltic pumps, MIBK, sample solution containing copper chelate of oxine, and air-segment sandwiched eluting solution (1.0 mol l⁻¹ nitric acid) were sequentially aspirated into an extraction coil made of PTFE tubing of 360 cm length and 0.5 mm i.d. The formation of organic film in the wall of the extraction coil, extraction of the copper chelate into the organic film and back-extraction of the analyte into the eluting solution occurred consecutively when these zones aspirated into the extraction coil were propelled down the extraction coil by a carrier solution at a flow rate of 2 ml min⁻¹. After leaving the extraction coil, the concentrated zone was transported to the nebulizer at its free uptake rate for atomization. Under the optimized conditions, an enrichment factor of 43 and a detection limit of 0.2 μg l⁻¹ copper were achieved at a sample throughput rate of 30 h⁻¹. Eleven determinations of a standard copper solution of 60 μg l⁻¹ gave a relative standard deviation of 1.5%. Foreign ions possibly present in tap water and natural water did not interfere with the copper determination. The developed method has been successfully used to the determination of copper content of tap water and river water.     

An Optical Relative Humidity Sensing System

The relative humidity (RH) of air is an important parameter that needs to be measured in many industries. Brook et al.^[1,2] studied the response of Nafion films containing Crystal Violet to the relative humidity; Raimundo et al.^[3] investigated the composition of Nafion-Crystal Violet films and their casting processes. In this paper, the sensing film was prepared by entrapped Crystal Violet in the commercial Nafion film. The dry air was commercially available and the 100% RH air was obtained by bubbling dry air into a series of bubbling flasks filled with deionized water. A spectrophotometer was employed to monitor the absorption changes of the film at the range of 400nm to 700 nm.     

Cloud point extraction for the determination of As(III) in water samples by electrothermal atomic absorption spectrometry

Cloud point extraction was applied as a preconcentration step for electrothermal atomic absorption spectrometry (ETAAS) determination of As(III) in aqueous solutions. After complexation with ammonium pyrrolidinedithiocarbamate, the analyte was quantitatively extracted to the surfactant-rich phase in the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114) after centrifugation. 0.1 mol L⁻¹ HNO₃ in methanol was added to the surfactant-rich phase before ETAAS determination. The precision (R.S.D.) for 11 replicate determinations of 5.0 μg L⁻¹ of As(III) was 3.0%. The concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for ETAAS determination and in the initial solution, was 36 for As(III). The linear concentration range was from 0.1 to 20 μg L⁻¹. The developed method was applied to the determination of As(III) in lake water and river water.     

Determination of tannic acid by direct chemiluminescence in a FIA assembly

The determination of tannic acid is performed in a FIA assembly on the basis of the analytical output obtained by oxidation of the acid. The analyte solution was daily prepared in a mixture of quinine as sensitiser and perchloric acid and it was injected into a pure water stream acting as a carrier. This solution merges with the mixture potassium permanganate in perchloric medium and the resulting chemiluminescence is monitored. The method was applied over the range 0.5–20 mg l⁻¹ of tannic acid with a LOD 100 μg l⁻¹. The reproducibility was 2.1% and the sample throughput 54 h⁻¹. The influence of foreign substances was studied and the new method is applied to the determination of tannic acid in pharmaceutical and galenic formulations in human urine and surface waters.     

Application of Ag2X (X = SO3, Cr2O7, C2O4 and CO3) solid-phase reagents for indirect determination of cyanide in the industrial effluent using FIA-FAAS system

Four solid-phase reagents have been tested for indirect determination of cyanide using flow injection analysis-flame atomic absorption spectrometry (FIA-FAAS). The method is based on insertion of aqueous cyanide solutions into an on-line Ag₂X (where X are SO₃²⁻, Cr₂O₇²⁻, C₂O₄²⁻ and CO₃²⁻) packed column (25%, m/m suspended on silica gel beads) and re-distilled water or sodium hydroxide are used as the carrier stream. The eluent containing the analyte as silver cyanide complexes, produced from reaction between Ag₂X and cyanide, measured by flame atomic absorption spectrometry. The method is simple, fast and selective than other published FIA procedures. A relative standard deviation (R.S.D.) better than 1.12% was obtained in a repeatability study. The method was applied to the determination of cyanide in industrial electrolytic baths.     

Decolorization and mineralization of textile dyes at solution bulk by heterogeneous nanophotocatalysis using immobilized nanoparticles of titanium dioxide

Nanophotocatalysis using nanostructured semiconductors constitute one of the emerging technologies for destructive oxidation of organics such as dyes. This paper deals with the decolorization and mineralization of reactive dyes by heterogeneous nanophotocatalysis using an immobilized TiO₂ nanoparticle photocatalytic reactor. A simple and effective method was used to immobilization of titanium dioxide nanoparticles. Reactive Orange 107 (RO 107, sulphatoethylsulphonyl reactive dye) and Reactive Red 152 (RR 152, monochlorotriazine reactive dye) were used as model compounds. UV–vis and ion chromatography (IC) analyses were employed to obtain the details of the photocatalytic degradation of the selected dyes. The effects of operational parameters such as H₂O₂, dye concentration, anions (NO₃⁻, Cl⁻, SO₄²⁻, HCO₃⁻ and CO₃²⁻) and pH were investigated. Formate, acetate and oxalate anions were detected as dominant aliphatic intermediates where, they were further oxidized slowly to CO₂. Nitrate, sulfate and chloride anions were detected as the photocatalytic mineralization of RO 107 and RR 152. Kinetics analysis indicates that the photocatalytic decolorization rates can usually be approximated zero-order model for RO 107 and first-order model for RR 152 dyes. Results show that the photocatalytic process occurred at solution bulk and the employment of optimal operational parameters may lead to complete decolorization and mineralization of dye solutions.     

Preparation of a novel fluorescence probe based on covalent immobilization by emulsion polymerization and its application to the determination of metronidazole

A novel method of preparing fluorescence particle probe by emulsion polymerization with covalent immobilization of indicator dye was described. A terminal double bond was attached to 3-amino-9-ethylcarbazole (AEC) via methacryloyl chloride, and the resultant compound was copolymerized with butyl methacrylate. The obtained polymer particles were used as a fluorescence probe, which is almost free of dye leaching, and has higher photostability and lower toxicity in comparison with free AEC. This probe holds great potential for the applications in intracellular measurements. In present study the prepared probe was used for the determination of metronidazole. The results revealed that the probe showed good selectivity and had a linear response to the analyte in the range from 2.0 × 10⁻⁵ to 1.0 × 10⁻³ mol l⁻¹ with a detection limit of 9.0 × 10⁻⁶ mol l⁻¹.     

Simultaneous potentiometric determination of ClO(3)(-)-ClO(2)(-) and ClO(3)(-)-HClO by flow injection analysis using Fe(III)-Fe(II) potential buffer

A rapid potentiometric flow injection technique for the simultaneous determination of oxychlorine species such as ClO₃⁻–ClO₂⁻ and ClO₃⁻–HClO has been developed, using both a redox electrode detector and a Fe(III)–Fe(II) potential buffer solution containing chloride. The analytical method is based on the detection of a large transient potential change of the redox electrode due to chlorine generated via the reaction of the oxychlorine species with chloride in the potential buffer solution. The sensitivities to HClO and ClO₂⁻ obtained by the transient potential change were enhanced 700–800-fold over that using an equilibrium potential. The detection limit of the present method for HClO and ClO₂⁻ is as low as 5×10⁻⁸ M with use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 0.5 M H₂SO₄. On the other hand, sensitivity to ClO₃⁻ was low when a potential buffer solution containing 0.5 M H₂SO₄ was used, but could be increased largely by increasing the acidity of the potential buffer. The detection limit for ClO₃⁻ was 2×10⁻⁶ M with the use of a 5×10⁻⁴ M Fe(III)–1×10⁻³ M Fe(II) buffer containing 0.3 M KCl and 9 M H₂SO₄. By utilizing the difference in reactivity of oxychlorine species with chloride in the potential buffer, a simultaneous determination method for a mixed solution of ClO₃⁻–ClO₂⁻ or ClO₃⁻–HClO was designed to detect, in a timely manner, a transient potential change with the use of two streams of potential buffers which contain different concentrations of sulfuric acid. Analytical concentration ranges of oxychlorine species were 2×10⁻⁵–2×10⁻⁴ M for ClO₃⁻, and 1×10⁻⁶–1×10⁻⁵ M for HClO and ClO₂⁻. The reproducibility of the present method was in the range 1.5–2.3%. The reaction mechanism for the transient potential change used in the present method is also discussed, based on the results of batchwise experiments. The simultaneous determination method was applied to the determination of oxychlorine species in a tap water sample, and was found to provide an analytical result for HClO, which was in good agreement with that obtained by the o-tolidine method and to provide a good recovery for ClO₃⁻ added to the sample.     

Repetitive determination of ascorbic acid using iron(III)-1.10-phenanthroline-peroxodisulfate system in a circulatory flow injection method

Ascorbic acid (AA) could be determined in large quantities of a co-existing oxidant. The incorporation of an on-line reagent regeneration step based on redox reaction eliminates the baseline drift in the procedure. This makes it possible to adopt a circulatory flow injection method (cyclic FIA) and to determine AA repetitively. The method is based on the reduction of iron(III) to iron(II) by the analyte, the reaction of the produced iron(II) with 1,10-phenanthroline (phen) in a weak acidic medium to form a colored complex, and the subsequent oxidation reaction of iron(II) to iron(III) by the co-existing peroxodisulfate. A solution (50 ml) of 3.0×10⁻⁴ mol l⁻¹ ferric chloride, 9.0×10⁻⁴ mol l⁻¹ phen and 5.0×10⁻² mol l⁻¹ ammonium peroxodisulfate in acetate buffer (0.2 mol l⁻¹, pH 4.5) is continuously circulated at a constant flow rate of 1.0 ml min⁻¹. Into this stream, an aliquot (20 μl) of the sample solution containing AA is quickly injected by means of a six-way valve. The complex formed is monitored spectrophotometrically (at 510 nm) in the flow system. The stream then returns to the reservoir after passing through a time-delay coil (50 m). The iron(II)–(phen)₃ complex is oxidized to iron(III)–(phen)₃ complex by peroxodisulfate which exists excessively in the circulating reagent solution. The proposed method allows as many as 300 repetitive determinations of 15 mg l⁻¹ AA with only 50 ml reservoir solution. The contents of AA in commercial pharmaceutical products were analyzed to demonstrate the capability of the developed system.     

Determination of very low levels of dissolved mercury(II) and methylmercury in river waters by continuous flow with on-line UV decomposition and cold-vapor atomic fluorescence spectrometry after pre-concentration on a silica gel-2-mercaptobenzimidazol sorbent

A new, simple and sensitive method for the simultaneous determination of mercury(II) and methylmercury chloride at sub-ng l⁻¹ levels in river waters is described. Inorganic and organic mercury were preconcentrated from fresh water samples simultaneously on a laboratory-made column containing 2-mercaptobenzimidazol loaded on silica gel and then quantitatively eluted with 0.05 M KCN solution and 2.0 M HCl to desorp inorganic and methylmercury species, respectively. After irradiation with an intensive UV source, MeHg⁺ was decomposed and mercury vapours were generated from inorganic and organic mercury using an acidic SnCl₂ solution in a continuous flow system and were subsequently determined with a cold vapour atomic fluorescence (CV-AFS) spectrometer. Detection limits (3σ) were 0.07 and 0.05 ng l⁻¹ (as Hg) for mercury(II) chloride and methylmercury chloride, respectively. Relative standard deviations of method (%R.S.D.) were 8.8 and 10 for inorganic and organomercuric species in the river water, respectively. The analysis of real samples, taken from different rivers, showed that inorganic mercury levels ranged from 4.0±0.6 to 12±1 ng l⁻¹ (as Hg and 95% confidence limit) and methylmercury levels at 0.2±0.02 ng l⁻¹(as Hg).     

两个不可逆电对共存体系的流动注射双安培分析法

流动注射分析已有电位法[1]、单安培法[2]和双安培法[3～8]等电化学检测方法.安培法比电位法灵敏,颇受重视.单安培法由于在控制工作电位范围内受其它可氧化还原物质的干扰,选择性不高.双安培法仪器装置较简单,但应用范围仅限于I2/I-,Fe3+/Fe2+等少数几种可逆电对体系.迄今为止,尚未见到将双安培法应用于不可逆体系的报道.本文讨论两个独立的不可逆电对共存的流动注射双安培检测法,以拓展双安培法的应用范围,并选用溶解氧分别与抗坏血酸、羟胺和联氨构成的3个体系进行了考察验证.1　实验部分1.1　仪器和试剂　流动注射双安培检测系统由IFI…     

Spectral characterization of a novel near-infrared cyanine dye: a study of its complexation with metal ions

The spectral features of the near-infrared (NIR) dye TG-170 in different solutions and its complexation with several metal ions were investigated. The absorbance maxima of the dye are at λ=819, 805, and 791 nm in dimethyl sulfoxide (DMSO), methanol, and a buffer of pH 5.9, respectively. These values match the output of a commercially available laser diode (780 nm), thus making use of such a source practical for excitation. The emission wavelengths of the dye are at λ_em =822, 812, and 803 nm in DMSO, methanol, and the buffer, respectively. The molar absorptivity and fluorescence quantum yield increase accordingly. The addition of either an Al(III) ion or Be(II) ion resulted in fluorescence quenching of the dye. The Stern–Volmer quenching constant, K_SV, was calculated from the Stern–Volmer plot to be K_SV=3.11×10⁵ M⁻¹ for the Al(III) ion and K_SV=1.17×10⁶ M⁻¹ for the Be(II) ion. The molar ratio of the metal to the dye was established to be 1:1 for both metal ions. The stability constant, K_S, of the metal–dye complex was calculated to be 4.37×10⁴ M⁻¹ for the Al–dye complex and 1.94×10⁶ M⁻¹ for the Be–dye complex.     

MIGRATION OF EXCITATION ENERGY FROM THIONINE TO METHYLENE BLUE IN MICELLES

Abstract— The main absorption bands of thionine (Th⁺) and methylene blue (MB⁺) in aqueous solution lie at 598 nm and 664 nm, respectively. This position permits excitation energy transfer from Th⁺ to MB⁺, but not vice versa. We describe here studies of such transfer between these molecules adsorbed on micelles of sodium lauryl sulfate (SLS), imitating, at least to some extent, the state of pigments in chloroplasts.
The SLS concentration was varied from 3.0 to 11 × 10^-3 M. In the presence of dye, aggregation to micelles, each containing 70–100 detergent molecules, begins at about 3.0 × 10^-3 M SLS. Practically all dye ions are adsorbed on these micelles as soon as their formation begins.
Energy transfer from adsorbed Th⁺ ions to adsorbed MB⁺ ions can be demonstrated by observing the quenching of the fluorescence of thionine and the sensitization of that of methylene blue.
At [Th⁺] = [MB⁺] = 1 × 10^-5 M , the most efficient energy transfer (82 per cent efficiency, as derived from measurements of the quenching of Th⁺ fluorescence, or 90 per cent, as derived from sensitization of MB⁺ fluorescence) is observed at the lowest SLS-concentration (3.0 × 10^-3 M ), when the only micelles present are those formed by aggregation of dye-carrying low molecular complexes of SLS with dye cations. Each micelle carries, under these conditions, 10–14 molecules of the two dyes, and the distance between two closest dye ions is about 16 A. Transfer becomes less efficient as the SLS-concentration increases, causing pigment molecules to distribute themselves among a greater number of micelles.     

Self-diffusion coefficient of water in Nafion-117 membrane with different monovalent counterions: a radiotracer study

The self-diffusion coefficient of water in Nafion-117 membrane in different cationic forms was measured by the transient radiotracer method, which is based on an analytical solution of Fick's second law. The self-diffusion coefficient of water in the membrane was obtained from the analysis of time-dependent isotopic-exchange rates of tritium tagged water between sample of Nafion-117 membrane and equilibrating water. This transient method does not require the knowledge of partition coefficient of water, which is an essential parameter in the radiotracer permeation method. In present work, self-diffusion coefficients of water in the Nafion-117 membrane with H⁺, Li⁺, Ag⁺, Na⁺, K⁺, Rb⁺ and Cs⁺ monovalent counterions were obtained. The values of logarithm of self-diffusion coefficients were found to vary linearly as a function of polymer volume fraction except for membrane sample with H⁺ counterions. The self-diffusion coefficient of water in Nafion-117 membrane with H⁺ counterions was significantly different from the trend observed in the variation of self-diffusion coefficient of water as a function of polymer volume fraction in the membrane with other monovalent counterions. This observation seems to suggest that the physical structure of Nafion-117 membrane in H⁺ form may be quite different from the Nafion-117 membrane with other monovalent counterions. The high self-diffusion coefficient of water (1.67 × 10⁻⁶ cm²/s) in Nafion-117 membrane with Cs⁺ counterions indicates that the ionic clusters in Nafion-117 membrane are well connected even at low water content (8.2 wt.%) in the membrane.     

基于硫代黄素T诱导G-四联体构成的生物传感器检测铅离子

硫代黄素T(ThT)荧光分子在自由状态下荧光强度很弱, 通过在Tris-HCl缓冲液中加入Pb²⁺的适配体即富含G的DNA序列, 可与ThT荧光分子形成G-四联体结构, 使荧光信号迅速增强; 向溶液中加入Pb²⁺, Pb²⁺与其适配体有很好的结合特异性, 可生成更牢固的G-四联体结构, 使ThT分子被释放出来, 导致溶液的荧光强度降低, 基于此可检测溶液中的Pb²⁺离子. 实验中优化了缓冲溶液组成、 ThT荧光分子浓度、 Pb²⁺适配体浓度及反应时间等条件. 结果表明, 在10 mmol/L Tris-HCl(pH=8.3, 含2 mmol/L MgCl₂)缓冲溶液中, ThT荧光分子和Pb²⁺适配体的浓度分别为10 μmol/L和200 nmol/L, 反应10 min时, 随着溶液中Pb ²⁺浓度的增加, 荧光强度减弱. Pb²⁺浓度在20~1000 nmol/L范围内时, 荧光强度与Pb²⁺的浓度呈现良好的线性关系(R²=0.9941), 检出限为1 nmol/L. 实际水样测试结果表明, 该方法的回收率在98.8%~101.3%之间. 该传感器灵敏、 快速、 无需化学修饰荧光分子且成本低.     

A sensitive flow-injection method for determination of trace amounts of nitrite

A new sensitive colour reaction for nitrite determination is presented. In acidic medium, nitrite was reacted with safranine to form a diazonium salt which caused the reddish-orange dye colour of the solution to change to blue. The carrier stream, into which the sample solution was injected, was doubly distilled water. The reagent solution stream, which contained safranine dye, hydrochloric acid and potassium chloride, was mixed with the carrier in a 3-m length of silicon tubing (bore 0.5 mm) maintained at 30°C in a thermostatic bath. The absorbance intensity was measured at 520 nm. The detection limit was 20 ng ml⁻¹ and the RSD% of 20 injections of 1 μg ml⁻¹ of nitrite was 0.65%. Analysis can be done at a rate of up to 30 h⁻¹. Under the optimum conditions in the concentration range of 30–4000 ng ml⁻¹ of nitrite ion, a linear calibration graph was obtained (r=0.9999). The method was applied successfully to the determination of nitrite in sausages.     

Pervaporation: An interface between fermentors and monitoring

An enzymic method for the determination of acetaldehyde applicable to the on-line monitoring of this analyte in fermentors has been proposed. The volatile analyte, after its separation by pervaporation, was collected in a stream containing NAD⁺, KC1 and 2-mercaptoethanol. The NADH formed was monitored spectrophotometrically at 340 nm. Different pervaporation temperatures were used, thus enlarging the determination range which was established between 1–100 μg ml⁻¹. The method, which provides excellent precision (RSD less than 3.5% in all instances) has been successfully applied to the determination of the analyte in spiked fermentation media.     

Determination of arsenic content in natural water by graphite furnace atomic absorption spectrometry after collection as molybdoarsenate on activated carbon

A sample solution containing less than 0.5 μg of As was adjusted to pH 2. As in the solution was collected on activated carbon (AC) as molybdoarsenate. The AC was directly introduced as an AC suspension into a graphite furnace atomizer, and the concentration of As was determined by atomic absorption spectrometry (AAS). This method is relatively free from interference caused by coexisting ions. The calibration curve was linear up to 0.1 mg l⁻¹, and limit of detection of As was 0.004 mg l⁻¹. When 1000 ml of sample solution is preconcentrated to 5 ml (enrichment factor is 200-fold) 0.02 μg l⁻¹ of As could be determined, and relative standard deviation was below 4.0% (by the deuterium background correction system). The method was applied to sea water and well water, and the sum of As(III) and As(V) was determined with satisfactory results.     

Reverse flow injection spectrophotometric determination of iron(III) using norfloxacin

A reversed flow injection colorimetric procedure for determining iron(III) at the μg level was proposed. It is based on the reaction between iron(III) with norfloxacin (NRF) in 0.07 mol l⁻¹ ammonium sulfate solution, resulting in an intense yellow complex with a suitable absorption at 435 nm. Optimum conditions for determining iron(III) were investigated by univariate method. The method involved injection of a 150 μl of 0.04% w/v colorimetric reagent solution into a merged streams of sample and/or standard solution containing iron(III) and 0.07 mol l⁻¹ ammonium sulfate in sulfuric acid (pH 3.5) solution which was then passed through a single bead string reactor. Subsequently the absorbance as peak height was monitored at 435 nm. Beer's law obeyed over the range of 0.2–1.4 μg ml⁻¹ iron(III). The method has been applied to the determination of total iron in water samples digested with HNO₃–H₂O₂ (1:9 v/v). Detection limit (3σ) was 0.01 μg ml⁻¹ the sample through of 86 h⁻¹ and the coefficient of variation of 1.77% (n=12) for 1 μg ml⁻¹ Fe(III) were achieved with the recovery of the spiked Fe(III) of 92.6–99.8%.