Determination of manganese and zinc in powdered chocolate samples by slurry sampling using sequential multi-element flame atomic absorption spectrometry

In the present work, a slurry sampling flame atomic absorption spectrometric method to determine directly manganese and zinc in powdered chocolate samples is proposed. The optimization step was performed using univariate methodology involving the following factors: nature and concentration of the acid solution, sonication time, and particle size. The established conditions led to the use of a sample mass of 150 mg, 2.0 mol L^− 1 nitric acid solution, sonication time of 15 min, and a slurry volume of 50 mL. This method allows the determination of manganese and zinc with detection limit of 52 and 61 ng g^− 1, respectively, and a precision expressed as relative standard deviation (RSD) of 2.6% and 3.2% (both, n = 10) for contents of manganese and zinc of 52.4 and 100.0 μg g^− 1, respectively. The proposed method was applied for determination of manganese and zinc in five powdered chocolate samples. In these, the manganese content varied from 42.8 to 52.7 and from 88.6 to 102.4 μg g^− 1 of zinc. The analytical results were compared with the results obtained by analysis of these samples after digestion using open vessel and acid bomb digestion procedures and determination using FS-FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Headspace solid-phase micro-extraction and gas chromatography-ion trap tandem mass spectrometry method for butyltin analysis in sediments: Optimization and validation

In this work, headspace solid-phase micro-extraction (SPME) combined with gas chromatography-mass spectrometry (GC-MS) method for analysis of butyltin compounds in sediment samples was upgraded by the introduction of tandem mass spectrometry (MS/MS). Optimization and validation of this method based on an one step procedure, tetraethylborate in situ ethylation with simultaneous extraction by headspace SPME, combined with tandem mass spectrometry is described. A simple leaching/extraction step of mono-(M), di-(D) and tri-(T) butyltin (BT) compounds from the sediment is required as sample pre-treatment. The combination of the two techniques headspace SPME and MS/MS, led to very little matrix interference which permitted to attain limits of detection three or more orders of magnitude lower than those attained in previous methods: 0.3 pg g^− 1 for MBT, 1 pg g^− 1 for DBT and 0.4 pg g^− 1 for TBT. Linear response range was from 0.02–1260 ng g^− 1 for MBT, 0.07–1568 ng g^− 1 for DBT and 0.04–2146 ng g^− 1 for TBT and RSD < 15% was also obtained. The method was efficiently applied to a real sample sediment from Sado River estuary in Portugal, revealing the existence of BTs pollution, as the TBT level of 189 ± 15 ng g^− 1 was much higher than the maximum established as provisional ecotoxicological assessment criteria.     

Use of a graphite–polyurethane composite electrode for electroanalytical determination of indole-3-acetic acid in soil samples

A new electroanalytical methodology was developed for the quantification of the phytohormone indole-3-acetic acid (IAA), using a graphite–polyurethane composite electrode (GPU) and the square wave voltammetry (SWV), in 0.1 mol L^− 1 phosphoric acid solution (pH 1.6). Analytical curves were constructed under optimized conditions (f = 100 s^− 1, a = 50 mV, E_i = 5 mV) and the reached detection and quantification limits were 26 μg L^− 1 and 0.2 mg L^− 1, respectively. The developed methodology is simple and accurate for the routine determination of IAA. In order to verify the application of the electroanalytical methodology in fortified soil samples without previous treatment, an IAA assay was performed without serious interferences of the soil constituents.     

Determination of copper in powdered chocolate samples by slurry-sampling flame atomic-absorption spectrometry

Chocolate is a complex sample with a high content of organic compounds and its analysis generally involves digestion procedures that might include the risk of losses and/or contamination. The determination of copper in chocolate is important because copper compounds are extensively used as fungicides in the farming of cocoa. In this paper, a slurry-sampling flame atomic-absorption spectrometric method is proposed for determination of copper in powdered chocolate samples. Optimization was carried out using univariate methodology involving the variables nature and concentration of the acid solution for slurry preparation, sonication time, and sample mass. The recommended conditions include a sample mass of 0.2 g, 2.0 mol L^–1 hydrochloric acid solution, and a sonication time of 15 min. The calibration curve was prepared using aqueous copper standards in 2.0 mol L^–1 hydrochloric acid. This method allowed determination of copper in chocolate with a detection limit of 0.4 g g^–1 and precision, expressed as relative standard deviation (RSD), of 2.5% (n=10) for a copper content of approximately 30 g g^–1, using a chocolate mass of 0.2 g. The accuracy was confirmed by analyzing the certified reference materials NIST SRM 1568a rice flour and NIES CRM 10-b rice flour. The proposed method was used for determination of copper in three powdered chocolate samples, the copper content of which varied between 26.6 and 31.5 g g^–1. The results showed no significant differences with those obtained after complete digestion, using a t-test for comparison.     

Potentiometric multi-syringe flow injection system for determination of exchangeable potassium in soils with in-line extraction

A multi-syringe flow injection system for the potentiometric determination of exchangeable potassium in soil samples is proposed. Firstly, a manifold was devised to allow determination in soil extracts prepared off-line. It was possible to analyze samples prepared in extractants with different composition (Mehlich or Morgan) without physical or chemical modification of the manifold. A linear dynamic concentration range of 6–391 mg L^− 1 was obtained, allowing the direct introduction of soil extract without dilution. A determination frequency of 50 h^− 1 was achieved, with good repeatability for 10 consecutive injections of soil extracts (RSD < 3.0%). The in-line preparation of soil extract was implemented by automatic addition of extractant solution to a previously weighed portion of soil, followed by in-line filtration. Good repeatability was attained as the variance of the extraction procedure was not significantly different from the variance obtained in consecutive measurements of the same extract. Furthermore, results comparable to those obtained by off-line extraction and determination by flame emission spectrometry were attained for the two soil samples tested. Using this procedure, a determination frequency of 13 h^− 1 and a sampling rate of 4 h^− 1 were achieved.     

Kinetic determination of organosulphur ligands by inhibition: Trace determination of cysteine and maleonitriledithiolate (MNDT)

Some organosulphur ligands have been found to inhibit the mercury(II) catalyzed substitution of cyanide in hexacyanoferrate(II) by N-methylpyrazinium ion (Mpz⁺). The inhibitory effect is due to the binding tendency of catalyst Hg²⁺ with these inhibitors. This effect has been used as a basis to develop a kinetic method for the determination of trace amounts of two organosulphur ligands viz. cysteine and MNDT. The reaction was followed spectrophotometrically at 655 nm by measuring the decrease in absorbance of the product [Fe(CN)₅Mpz]²⁻. The influence of the reaction variables has also been studied. A general mechanistic scheme of the indicator reaction system including the role of inhibitor has been proposed and applied to determine the organosulphur ligands. Under the selected experimental conditions cysteine and MNDT have been determined in the range of 2–20 × 10^− 7 M and 5 × 10^− 8 M to 12 × 10^− 7 M respectively in various aqueous samples. The analytical concentration range depends upon the amount of Hg²⁺ present in the indicator reaction and also on the stability of the Hg²⁺-inhibitor complex in question. Under specified conditions, the detection limit for cysteine and MNDT are 2 × 10^− 7 M and 5 × 10^− 8 M respectively. The influences of possible interference by major amino acids, on the determination of cysteine and their limits have been investigated.     

Occurrence of ochratoxin A in Turkish wines

A total of 95 wine samples including 34 white, 10 rosé and 51 red wines originating from four different Turkish areas were analysed for ochratoxin A (OTA). An analytical method based on immunoaffinity column (IAC) for clean-up and high performance liquid chromatography with fluorescence detection (HPLC-FD) was used to determine OTA in wines. The limit of detection (LOD) was estimated as 0.006 ng ml^− 1 for white wine and 0.010 ng ml^− 1 for rosé and red wines. The limit of quantification (LOQ) was estimated as 0.020 ng ml^− 1 in white wine and 0.030 ng ml^− 1 in rosé and red wines. Recovery experiments were carried out with spiked samples in the range 0.1–1 ng ml^− 1 of OTA. The average OTA recoveries from spiked white wine samples varied from 79.43% to 85.07%; while the mean recoveries for rosé and red wine samples were in the range of 77.48–83.96% and 76.61–83.55%, respectively. OTA was detected in 82 (86%) wine samples at levels of < 0.006–0.815 ng ml^− 1, which were below the maximum allowable limit established by the European Community. The mean OTA concentration in red wines was slightly higher than in white and rosé wines. Furthermore, our data indicate that the geographic region of origin has strong influence on OTA level for white, rosé and red wines: wines originating from Thrace (n = 44, mean = 0.158 ng ml^− 1) and Aegean (n = 28, mean = 0.060 ng ml^− 1) regions of Turkey were more contaminated with OTA compared with wines originating from central (n = 15, mean = 0.027 ng ml⁻¹) and east Anatolia (n = 8, mean = 0.027 ng ml^− 1) areas. This study showed that the occurrence of OTA in Turkish wines is high, but at levels that probably leads to a non-significant human exposure to OTA by consumption of wines.     

L-Cysteine-coated CdSe/CdS core-shell quantum dots as selective fluorescence probe for copper(II) determination

Quantum dots (QDs) or semiconductor nanocrystals have been receiving great interest in the last few years. In this paper, L-cysteine-coated CdSe/CdS core-shell QDs (λ_em = 585 nm) have been prepared, which have excellent water-solubility. The full width at half maximum (FWHM) of the photoluminescence of these nanocrystals is very narrow (about 30 nm), and the quantum yield (QY) is 15% relative to Rhodamine 6G in ethanol (QY = 95%). With excess free L-cysteine in the solution, the fluorescence intensity of L-cysteine-coated CdSe/CdS QDs showed improved stability. It was found that the fluorescence of L-cysteine-capped CdSe/CdS QDs could be quenched only by copper (II) ions and was insensitive to other physiologically important cations, such as Ca²⁺, Mg²⁺, Zn²⁺, Al³⁺, Fe³⁺, Mn²⁺ and Ni²⁺ etc. Based on this finding, the quantitative analysis of Cu²⁺ with L-cysteine-capped CdSe/CdS QDs has been established. The linear range was from 1.0 × 10^− 8 to 2.0 × 10^− 7 mol L^− 1 and the limit of detection (LOD) was 3.0 × 10^− 9 mol L^− 1 (S/N = 3). The proposed method has first been applied to the determination of Cu²⁺ in vegetable samples with recoveries of 99.6–105.8%.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Determination of 4-methylbenzilidene camphor in sunscreen by square wave voltammetry in media of cationic surfactant

The voltammetric behavior of 4-methylbenzelidene camphor (MBC) was studied by square wave voltammetry (SWV) using mercury electrode. The experimental condition that provided the highest peak current with the best reduction signal definition of MBC was found in Britton-Robinson buffer and cationic surfactants, cetyltrimethylammoniun bromide (CTABr). A single peak of MBC reduction was observed at − 1.21 V versus Ag/AgCl. The developed methodology was applied for determination of MBC in commercial sunscreen SPF 15, 20 and 30 and for the simultaneous determination when other protection agents were associated, such as benzophenone-3 (BENZO) and octyl methoxycinammate (OMC). Both methodologies had shown good determination values for the analyzed samples. The calculated detection limit was 2.99 × 10^− 9 mol L^− 1 and the quantification limit was 9.98 × 10^− 9 mol L^− 1.     

Assay of femtogram level nitrite in human urine using luminol–myoglobin chemiluminescence

In this paper, a sensitive flow injection chemiluminescence system luminol–myoglobin was described for determining femtogram nitrite. Nitrite bound myoglobin producing the ferric heme nitrite complexes, which catalyzed the electron transfer of luminol to myoglobin leading to fast chemiluminescence. The chemiluminescence intensity in the presence of nitrite was remarkably enhanced compared with that in the absence of it. Under the optimum reaction conditions the chemiluminescence increment produced was proportional to the concentration of nitrite in the range of 0.05 pg ml^− 1–1.0 ng ml^− 1 (R² = 0.9991), with a detection limit (3σ) of 20.0 fg ml^− 1. At the flow rate of 2.0 ml min^− 1, the whole process including sampling and washing could be completed in 0.5 min offering the sampling efficiency of 120 h^− 1 accordingly, and the relative standard deviation (RSD) was less than 2.60% (n = 5). It was satisfactory for the application to determine nitrite in human urine samples, and the possible mechanism was proposed.     

Determination of linuron in water samples by high performance liquid chromatography after preconcentration with octadecyl silanized magnetite

A sensitive and selective batch adsorption method is proposed for the preconcentration and determination of linuron. Linuron was preconcentrated on octadecyl silanized (ODS) magnetite as an adsorbent and then determined by high performance liquid chromatography (HPLC). Several parameters on the recovery of the analyte were investigated. The experimental results showed that it was possible to obtain sufficient preconcentration efficiency when the solution pH was 6 using 100 mL of sample solution containing 1.0 μg of linuron and 3 mL of ethanol as a desorption solution. Recovery of linuron was 50.7 ± 1.9% with a relative standard deviation for five determinations of 3.0% under optimum conditions. The calibration curve of linuron was linear up to 200 ng mL^− 1 with a correlation coefficient of 0.998 and the detection limit (3S/N) was 1.0 ng mL^− 1. The capacity of the adsorbent was also examined and found to be 0.15 mg g^− 1 for linuron. ODS-magnetite is suitable for repeated use without decreasing recovery at least 4 adsorption–desorption cycles. The proposed method was successfully applied to the determination of linuron in river water with high precision and accuracy.     

Determination of Fe, Ni and V in asphaltene by ICP OES after extraction into aqueous solutions using sonication or vortex agitation

A simple procedure for the extraction of Fe, Ni and V from asphaltene into acid solutions prior to the ICP OES determination is proposed. Either sonication or vortex agitation was used to disperse the organic sample into concentrated nitric acid, achieving efficient analyte extraction into the aqueous acid solution. Both procedures were compared and the advantage of the ultrasound-assisted procedure was evaluated. In both cases, pre-heating of sample–acid mixtures was necessary to enable quantitative extractions. Optimized conditions for the ultrasonic bath were established: 1 L of water at room-temperature, 20 min of sonication and tubes (maximum of eight) in vertical position. By using the vortex, 50 min of vigorous mechanical agitation was needed for each one of the tubes containing samples. The acid solution obtained after extraction was directly aspirated into the ICP in order to perform quantification by optical emission. Calibration was made with aqueous analyte standards containing Sc as internal standard. The procedures were tested using certified fuel oil (SRM NIST 1634c) and the method was applied for the determination of Fe, V and Ni in one asphaltene sample obtained by the fractionation of the SRM NIST 1634c. Recoveries above 90% were achieved and limits of quantification in the asphaltene sample were 1.5, 15 and 1.0 μg g^− 1 estimated for Fe, Ni and V, respectively.     

Speciation analysis of selenium enriched green onions (Allium fistulosum) by HPLC-ICP-MS

Green onions (Allium fistulosum) enriched with 10 or 100 μg mL^− 1 Se(IV) or SeMet were analyzed for total selenium and species distribution. Anion and cation exchange chromatographies were applied for the separation of selenium species with mass spectrometric detection. Two different sample preparation methods (NaOH and enzymatic) were compared from the Se extraction efficiency point of view. Total selenium concentration accumulated by the onions reached the 200 μg g^− 1 level expressed for dry weight when applying SeMet at a concentration of 100 μg mL^− 1 as the source of Se. Speciation studies revealed that both in onion bulbs and leaves the predominant form of organic selenium is Se-methyl-selenocysteine (MeSeCys). When Se(IV) was applied for Se-enrichment at a concentration level of 100 μg mL^− 1 both onion leaf and bulb contained a significant amount of inorganic selenium. An unknown compound was also detected.     

Synthesis of amberlite XAD-2-PC resin for preconcentration and determination of trace elements in food samples by flame atomic absorption spectrometry

A new chelating sorbent has been developed using Amberlite XAD-2 resin anchored with pyrocatechol through –N=C– group. This sorbent, characterised by elemental analysis and infrared (IR) spectra, was used as packing for the minicolumn in an on-line system preconcentration system for cadmium, cobalt, copper and nickel determination. Metal ions were sorbed in the minicolumn, from which it could be eluted directly to the nebulizer–burner system of the flame atomic absorption spectrometer (FAAS). Elution of all metals from minicolumn can be made with 0.50 mol L^− 1 HCl or HNO₃. The enrichment factors obtained were 16 (Cd), 24 (Co), 15 (Cu) and 19 (Ni), for 60 s preconcentration time, and 39 (Cd), 69 (Co), 36 (Cu) and 41 (Ni), if used 180 s preconcentration time. Under the optimum conditions, the proposed procedure allowed the determination of cadmium, cobalt, copper and nickel with detection limits of 0.31, 0.32, 0.39 and 1.64 μg L^− 1, respectively, when used preconcentration periods of 180 s. The accuracy of the developed procedure was sufficient and evaluated by the analysis of the certified reference materials NIST 1515 apple leaves and NIST 1570a spinach leaves. The method was applied to the analysis of food samples (spinach, black tea and rice flour).     

On-line molecularly imprinted solid phase extraction for the selective spectrophotometric determination of catechol

A molecularly imprinted polymer has been synthesized for a selective on-line catechol extraction, followed by its spectrophotometric determination in guarana powder, mate tea and tap water samples. A clean-up column, containing a methacrylic polymer + C₁₈ solid phase, was also used in order to enhance selectivity. The imprinted polymer was prepared by bulk polymerization using catechol as template and 4-vinylpyridine as the functional monomer. Permanganate solution was used as spectrophotometric reagent, where Mn(VII) was reduced to Mn(II) by catechol in an acid medium, causing color loss, which was monitored at 528 nm. Physical (extraction flow rate, elution flow rate, coil length) and chemical (nature and concentration of the eluent, potassium permanganate concentration) variables were optimized, and the selectivity was appraised using three molecules (4-chloro-2-methylphenol, 2-cresol, 2-methoxyphenol) similar to catechol. These molecules did not present interference in 1:8, 1:10 and 1:10 (catechol/concomitant) proportions, respectively. The analytical calibration curve ranged from 3.0 up to 100 μmol L^− 1 (r > 0.999; seven concentrations levels, n = 3) and the limits of detection (LOD) and quantification (LOQ) were 0.8 and 2.7 μmol L^− 1, respectively. Precision, expressed as RSD, was of 3.0% (20 μmol L^− 1, n = 10), and the analytical frequency was 15 h^− 1. Accuracy was checked by the HPLC technique and the results did not present significant difference at 95% confidence levels according to the t test.     

Development and critical comparison of greener flow procedures for nitrite determination in natural waters

Two greener procedures for flow-injection spectrophotometric determination of nitrite in natural waters were developed and critically compared. Replacement of toxic reagents, waste minimization and treatment were exploited to attend the standards of clean chemistry. The flow system was designed with solenoid micro-pumps in order to minimize reagent consumption and waste generation. The first procedure is based on the Griess diazo-coupling reaction with sulfanilamide and N-(1-naphthyl)ethylenediamine (NED) yielding an azo dye, followed by photodegradation of the low amount of waste generated based on the photo-Fenton reaction. The second procedure is based on the formation of iodine from nitrite and iodide in acid medium in order to avoid the use of toxic reagents. For Griess method, linear response was achieved up to 1.0 mg L^− 1, described by the equation A = − 0.007 + 0.460C (mg L^− 1), r = 0.999. The detection limit was estimated as 8 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.8% (n = 20). The sampling rate was estimated as 108 determinations per hour. The consumption of the most toxic reagent (NED) is reduced 55-fold and 20-fold in comparison to batch method and flow injection with continuous reagent addition, respectively. A colorless residue was obtained by in-line photodegradation with reduction of 87% of the total organic carbon content. The results obtained for natural water samples were in agreement with those achieved by the reference method at the 95% confidence level. For the nitrite–iodide method, linear response was observed up to 2.0 mg L^− 1, described by the equation A = − 0.024 + 0.148C (mg L^− 1), r = 0.999. The detection limit was estimated as 25 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.6% (n = 20). The sampling rate was estimated as 44 determinations per hour. Despite avoiding the use of toxic reagents, the nitrite–iodide method presented worst performance in terms of selectivity and sensitivity.     

Combined use of Pd and HF as chemical modifiers for the determination of total chromium in produced waters from petroleum exploration by ET AAS

This work reports the evaluation of the combined use of Pd and HF as chemical modifiers for the direct determination of total chromium in waters derived from petroleum exploration employing electrothermal atomic absorption spectrometry (ET AAS). Such waters, usually called as produced waters, have complex composition presenting a number of organic and inorganic substances. When obtained from offshore operations they also present high salinity. In order establish conditions for chromium measurement pyrolysis and atomization curves were built up in different media and employing Pd and HF as chemical modifiers. Also, a detailed study about calibration strategy was performed. At best conditions, pyrolysis and atomization temperatures were 1200 °C and 2600 °C, respectively, and 10 μL of a 500 mg L^− 1 Pd solution was added together with 10 μL of a 50% (v/v) HF solution on 20 μL of sample. Obtained results indicate that, in this kind of sample, chromium can be determined by standard addition method or employing external calibration with standard solutions prepared in 0.8 mol L^− 1 NaCl medium. In order to evaluate the accuracy of the procedure, a recovery test was performed with seven spiked samples of produced waters. The detection limit, quantification limit and the relative standard deviation in 0.8 mol L^− 1 NaCl were also calculated and the values found were 0.45 μg L^− 1, 1.5 μg L^− 1 and 6.0% (at 2.5 μg L^− 1 level), respectively.     

Tyrosinase/laccase bienzyme biosensor for amperometric determination of phenolic compounds

Tyrosinase/laccase bienzyme biosensor for amperometric determination of phenolic compounds was constructed. Enzymes were immobilized in titania gel matrix. The obtained biosensor was successfully used for determination of 2,6-dimethoxyphenol, 4-tertbutylcatechol, 4-methylcatechol, 3-chlorophenol and catechol. The highest sensitivity and the widest linear range were noticed for catechol, 234 mA L mol^− 1 and 2.0 × 10^− 7–3.2 × 10^− 5 mol/L, respectively. Detection limit for catechol, at signal-to-noise ratio of 3 was 1.3 × 10^− 7 mol/L.