Nickel catalysis enables convergent paired electrolysis for direct arylation of benzylic C–H bonds期刊界 All Journals 搜尽天下杂志传播学术成果专业期刊搜索期刊信息化学术搜索

按检索

Nickel catalysis enables convergent paired electrolysis for direct arylation of benzylic C–H bonds

Authors:

Institution:

Laboratory of Inorganic Synthesis and Catalysis, Institute of Chemical Sciences and Engineering, Ecole Polytechnique Fédérale de Lausanne (EPFL), ISCI-LSCI BCH 3305, 1015 Lausanne Switzerland,

Abstract:

Convergent paired electrosynthesis is an energy-efficient approach in organic synthesis; however, it is limited by the difficulty to match the innate redox properties of reaction partners. Here we use nickel catalysis to cross-couple the two intermediates generated at the two opposite electrodes of an electrochemical cell, achieving direct arylation of benzylic C–H bonds. This method yields a diverse set of diarylmethanes, which are important structural motifs in medicinal and materials chemistry. Preliminary mechanistic study suggests oxidation of a benzylic C–H bond, Ni-catalyzed C–C coupling, and reduction of a Ni intermediate as key elements of the catalytic cycle.

A direct arylation of benzylic C–H bonds is achieved by integrating Ni-catalyzed benzyl–aryl coupling into convergent paired electrolysis.

Electrochemical organic synthesis has drawn much attention in recent years.¹ Compared to processes using stoichiometric redox agents, electrosynthesis can potentially be more selective and safe, generate less waste, and operate under milder conditions.^1b In the majority of examples, the reaction of interest occurs at one electrode (anode for oxidation or cathode for reduction), while a sacrificial reaction occurs at the counter electrode to fulfil electron neutrality.^1a,2 Paired electrolysis uses both anodic and cathodic reactions for the target synthesis, thereby maximizing energy efficiency.^1a,3 However, there are comparatively few examples of paired electrolysis for organic synthesis.^1a,3,4Paired electrolysis might be classified into three types: parallel, sequential, and convergent (Fig. 1).^1a,3a In parallel paired electrolysis (Fig. 1a), the two half reactions are simultaneous but non-interfering. In sequential paired electrolysis (Fig. 1b), a substrate is oxidized and reduced (or vice versa) sequentially. In convergent paired electrolysis (Fig. 1c), intermediates generated by the anodic and cathodic processes react with one another to yield the product.^1a,3a,4b,c,5 The activation mode of all three types of paired electrolysis is based on the innate redox reactivity of substrates. As a result, the types of reactions that could be conducted by paired electrolysis remain limited. We proposed a catalytic version of convergent paired electrolysis, where a catalyst is used to cross-couple the two intermediates generated at the two separated electrodes (Fig. 1d). Although mediators have been used in paired electrosynthesis,^3a,4c,6 catalytic coupling of anodic and cathodic intermediates remains largely undeveloped. This mode of action will leverage the power of cross-coupling to electrosynthesis, opening up a wide substrate and product space. Here we report the development of such a process, where cooperative nickel catalysis and paired electrolysis enable direct arylation of benzylic C–H bonds (Fig. 1e).Open in a separate window Fig. 1Different types of paired electrolysis: (a) parallel paired electrolysis, (b) sequential paired electrolysis, (c) convergent paired electrolysis, (d) catalytic convergent paired electrolysis and (e) this work.Our method can be used to synthesize diarylmethanes, which are important structural motifs in bioactive compounds,⁷ natural products⁸ and materials.⁹ Direct arylation of benzylic C–H bonds has been recognized as an efficient strategy to synthesize diarylmethanes, and methods using metal catalysis¹⁰ and in particular combined photoredox and transition-metal catalysis have been reported.¹¹ Electrosynthesis provides a complementary approach to these methods, with the potential advantages outlined above. The groups of Yoshida¹² and Waldvogel¹³ previously developed synthesis of diarylmethanes via a Friedel–Crafts-type reaction of a benzylic cation and a nucleophile. The benzylic cations were generated by anodic oxidation of benzylic C–H bonds.¹⁴ To avoid the overoxidation of products and to stabilize the very reactive benzylic cations, the reactions had to be conducted in two steps, where the benzylic cations generated in the anodic oxidation step had to be trapped by a reagent. We thought a Ni catalyst could be used to trap the benzyl radical to form an organonickel intermediate, which is then prone to a Ni-catalyzed C–C cross-coupling reaction. Although such a coupling scheme was unprecedented, Ni-catalyzed electrochemical reductive coupling of aryl halides was well established.¹⁵ We were also encouraged by a few recent reports of combined Ni catalysis and electrosynthesis for C–N,¹⁶ C–S,¹⁷ and C–P¹⁸ coupling reactions.We started our investigations using the reaction between 4-methylanisole 1a and 4-bromoacetophenone 2a as a test reaction (11a,b,11d–f To improve the reaction efficiency, we decided to use only 3 equivalents of 4-methylanisole 1a relative to 2a. After some initial trials, we decided to conduct the reaction in an undivided cell using a constant current of 3 mA. These conditions are straightforward from a practical point of view. After screening various reaction parameters, we found that a combination of 4,4′-dimethoxy-2-2′-bipyridine (L1) and (DME)NiBr₂ as a catalyst, THF/CH₃CN (4 : 1) as a solvent, fluorine-doped tin oxide (FTO) coated glass as an anode and carbon fibre as a cathode gave a 50% GC yield of 1-(4-(4-methoxybenzyl)phenyl)ethanone 3a after 18 h (†).Summary of the influence of key reaction parameters^a


Entry	Ligand	Anode	Cathode	Solvent	Yield (%)
1	L1	FTO	Carbon fibre	THF/CH₃CN = 4 : 1	56
2	L1	FTO	Carbon fibre	THF/CH₃CN = 4 : 1	76^b
3	L2	FTO	Carbon fibre	THF/CH₃CN = 4 : 1	43
4	L3	FTO	Carbon fibre	THF/CH₃CN = 4 : 1	46
5	L4	FTO	Carbon fibre	THF/CH₃CN = 4 : 1	21
6	L1	FTO	Carbon fibre	CH₃CN	4
7	L1	FTO	Carbon fibre	DMA	15
8	L1	FTO	Carbon fibre	DMF	6
9	L1	FTO	Ni foam	THF/CH₃CN = 4 : 1	45
10	L1	FTO	Pt foil	THF/CH₃CN = 4 : 1	28
11	L1	Carbon fibre (1 cm²)	Carbon fibre	THF/CH₃CN = 4 : 1	0
12	L1	Pt foil (cm²)	Carbon fibre	THF/CH₃CN = 4 : 1	7

Open in a separate window^aReaction conditions: 1a (0.6 mmol), 2a (0.2 mmol), (DME)NiBr₂ (6 mol%), ligand (7.2 mol mol%), LutHClO₄ (0.1 M), and lutidine (0.8 mmol) in solvent (2 mL) at 40 °C. GC yield.^bReaction time: 36 h. Isolated yield.With the optimized reaction conditions in hand, we explored the substrate scope (

Open in a separate window^aReaction conditions: 1 (0.6 mmol), 2 (0.2 mmol), (DME)NiBr₂ (6 mol%), L1 (7.2 mol mol%), LutHClO₄ (0.1 M), and lutidine (0.8 mmol) in THF/CH₃CN (4 : 1, 2 mL) at 40 °C. Isolated yield.^b(DME)NiBr₂ (5 mol%) and L1 (6 mol%) were used as the catalysts.^cNi(acac)₂ was used instead of (DME)NiBr₂.^dSolvent: THF/CH₃CN (3 : 1, 2 mL).^e2 mmol toluene or its derivative was used as the substrate.^fReaction time: 60 h.Linear sweep voltammetry (LSV) was applied to probe the possible processes at both the anode and cathode. The measurements were made in THF/CN₃CN (4 : 1, 2 mL) using LutH]ClO₄ (0.1 M) as the electrolyte and lutidine (0.4 M) as an additional base to mimic the coupling conditions. The LSV curves of individual reaction components indicate that only 4-methylanisole 1a and the Ni catalyst may be oxidized at the anode (Fig. 2a). The current at 3 mA appears to be the sum of the oxidation currents of 1a and the Ni catalyst. Meanwhile, LSV curves indicate that only the Ni catalyst might be reduced at the cathode (Fig. 2b).Open in a separate window Fig. 2The LSV curves of different reaction components at the anode or cathode. The components were dissolved in THF/CN₃CN (4 : 1, 2 mL); the solution also contained LutH]ClO₄ (0.1 M) and lutidine (0.4 M). Scan rate: 50 mV s⁻¹. (a) The LSV curves of different reaction components at the FTO anode; (b) the LSV curves of different reaction components at the carbon fibre cathode; (c) the LSV curves of different reaction components at the carbon fibre anode.It was observed that FTO was an essential anode for the reactions. If FTO was replaced by a carbon fibre anode, no coupling product was obtained. LSV was performed to probe the oxidation of 1a and the Ni catalyst on a carbon fibre anode (Fig. 2c). The oxidation of the Ni catalyst was much easier on carbon fibre than on FTO. At 3 mA, the oxidation is exclusively due to the Ni catalyst. This result suggests that the absence of coupling on the carbon fibre anode is due to no oxidation of 1a. The different redox properties of 1a and the Ni catalyst observed on different electrodes might be attributed to the different nature of surface species which influence the electron transfer. Although FTO is rarely used in electrosynthesis, it is widely used in electrocatalysis and photoelectrocatalysis for energy conversion.¹⁹ FTO is stable, commercially available and inexpensive. In our reactions, the FTO anode could be reused at least three times.The LSV curves in Fig. 2 revealed the issue of “short-circuit” of catalyzed/mediated paired electrolysis in an undivided cell, as the catalyst or mediator can be reduced and oxidized at both the cathode and anode. When carbon fibre or graphite was used as the anode, the short-circuit problem was very severe so that nearly no current was used for electrosynthesis. However, by using an appropriate anode such as FTO, the short-circuit problem was alleviated and around half of the current was used to oxidize the substrate (1a) while the other half was used to oxidize the nickel complex. The remaining short-circuit is one of the reasons why the current efficiencies of the reactions are low (<10%). Another factor contributing to the low current efficiency is the instability of the benzyl radical, which can abstract hydrogen from the solvent to regenerate the substrate. Nevertheless, useful products could be obtained in synthetically useful yields under conditions advantageous to previous methods.For the test reaction (†). These data support the formation of a benzyl radical intermediate. As bromide existed in our reaction system, it is possible to be oxidized to form a bromine radical. Previous studies showed that a bromine radical can react with a toluene derivative to give a benzyl radical.^11b,g,20 To probe the involvement of the Br radical, we conducted a coupling of 4-methylanisole 1a with 4′-Iodoacetophenone, using Ni(acac)₂ instead of (DME)NiBr₂ as the Ni source. We obtained a GC yield of 24% for the coupling after 18 h (Scheme S2^†). This result suggests that a Br-free path exists for the coupling, although a non-decisive involvement of Br⁻/Br˙ cannot be ruled out.Based on the data described above, we propose a mechanism for the coupling (Scheme 1). The oxidation of a toluene derivative at the anode gives a benzyl radical. This radical is trapped by a LNi(ii)(Ar)(Br) species (B) in the solution to give a LNi(iii)(Ar)(benzyl)(Br) intermediate (C). The latter undergoes reductive elimination to give a diarylmethane and a LNi(i)(Br) species (A). There are at least two ways A can be convert to B to complete the catalytic cycle: either by oxidative addition of ArBr followed by a 1-e reduction at the cathode or by first 1-e reduction to form a Ni(0) species followed by oxidation addition of ArBr. In addition to a toluene derivative, a Ni species is oxidized at the anode. We propose that this oxidation is an off cycle event, which reduces the faradaic and catalytic efficiency but does not shut down the productive coupling.Open in a separate window Scheme 1Proposed mechanism of the direct arylation of benzylic C–H bonds.

Keywords:

设为首页 | 免责声明 | 关于勤云 | 加入收藏