首页 | 本学科首页   官方微博 | 高级检索  
     

送粉角度对激光熔覆铁基复合涂层形状特征的影响
引用本文:蔡川雄,刘洪喜,张晓伟,王传琦,蒋业华. 送粉角度对激光熔覆铁基复合涂层形状特征的影响[J]. 强激光与粒子束, 2013, 25(6): 1359-1364. DOI: 10.3788/HPLPB20132506.1359
作者姓名:蔡川雄  刘洪喜  张晓伟  王传琦  蒋业华
作者单位:1.昆明理工大学 材料科学与工程学院, 昆明 650093
摘    要:通过分析激光熔覆过程中光束、粉末和熔池间的作用机理,建立了送粉式激光熔覆材料有效利用率的数学模型,在此基础上推导了送粉角度与工艺参数之间的定量关系式,并计算了不同送粉角度下的熔覆材料有效利用率、熔高和横截面积。结果表明,在熔覆工艺参数不变的条件下,理论计算的熔覆材料有效利用率、熔覆层高度和横截面积均随送粉角度的增加而增大,且均高于实验检测值。激光熔覆过程中,由于粉末烧损和机械损失,使熔覆材料有效利用率、熔高和横截面积随送粉角度变化出现最大值,理想送粉角度为60。

关 键 词:激光熔覆   有效利用率   送粉角度   成形质量
收稿时间:2012-11-01;

Influence of powder feeding angle on geometric parameters of laser-clad Fe-based composite coating
Cai Chuanxiong,Liu Hongxi,Zhang Xiaowei,Wang Chuanqi,Jiang Yehua. Influence of powder feeding angle on geometric parameters of laser-clad Fe-based composite coating[J]. High Power Laser and Particle Beams, 2013, 25(6): 1359-1364. DOI: 10.3788/HPLPB20132506.1359
Authors:Cai Chuanxiong  Liu Hongxi  Zhang Xiaowei  Wang Chuanqi  Jiang Yehua
Affiliation:1.School of Materials Science and Engineering,Kunming University of Science and Technology,Kunming 650093,China
Abstract:According to the reaction mechanism of laser beam, powder particles and melting pool during the laser cladding process, a mathematical model of powder utilization efficiency was formulated. A quantitive expression describing the relation between the powder injection angle and the contour parameters of laser cladding coating was obtained. Based on thermo-physical properties of Fe55 alloy powder and laser cladding process parameters, the powder utilization efficiency, cladding coating height and cross-section area were calculated by means of AutoCAD software. The results show that the powder utilization efficiency, and cladding coating height and cross-section area increase with the powder injection angle increasing, and theoretically calculated values are larger than the experimental values. Owing to powder burning and mechanical losing in the process of laser cladding, the powder utilization efficiency, and cladding coating height and cross-section area reach their maxima simultaneously with the variation of powder injection angle. The ideal powder injection angle is 60°.
Keywords:utilization efficiency  powder injection angle  forming quality
点击此处可从《强激光与粒子束》浏览原始摘要信息
点击此处可从《强激光与粒子束》下载免费的PDF全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号