| 切削用量对铝靶表面质量的影响 |
| |
| 引用本文： | 谢军,黄燕华,杜凯,袁光辉,郑凤成,黄丽珍,朱磊. 切削用量对铝靶表面质量的影响[J]. 强激光与粒子束, 2005, 17(11): 1693-1695 |
| |
| 作者姓名： | 谢军 黄燕华 杜凯 袁光辉 郑凤成 黄丽珍 朱磊 |
| |
| 作者单位： | 中国工程物理研究院 激光聚变研究中心 ，四川 绵阳 621900 |
| |
| 基金项目： | 国家863计划项目资助课题.致谢：本研究工作得到了唐永建研究员、张林研究员、吴卫东副研究员、李波副研究员等专家的关心、指导和支持,以及高党忠、马小军、张继成等同志的帮助,在此表示衷心感谢. |
| |
| 摘 要： | 采用单点金刚石切削技术，完成了对ICF实验用铝靶的切削加工，重点研究了切削用量对加工表面质量的影响。实验结果表明：采用较小的进给速度，较大的主轴转速能够获得较低的表面粗糙度，切削深度对表面质量影响较小。通过Form Talysurf 表面轮廓仪测量，结果表明表面粗糙度小于50 nm。
|
| 关 键 词： | 单点金刚石切削 惯性约束聚变 铝靶 表面粗糙度 |
| 文章编号： | 1001-4322(2005)11-1693-03 |
| 收稿时间： | 2004-08-23 |
| 修稿时间： | 2005-04-11 |
Effect of cutting conditions on surface roughness of aluminum target |
| |
| XIE Jun,HUANG Yan-hua,DU Kai,YUAN Guang-hui,ZHENG Feng-cheng,HUANG LI-zhen,ZHU Lei. Effect of cutting conditions on surface roughness of aluminum target[J]. High Power Laser and Particle Beams, 2005, 17(11): 1693-1695 |
| |
| Authors: | XIE Jun HUANG Yan-hua DU Kai YUAN Guang-hui ZHENG Feng-cheng HUANG LI-zhen ZHU Lei |
| |
| Affiliation: | Research Center of Laser Fusion, CAEP, P. O. Box 919-987, Mianyang 621900, China |
| |
| Abstract: | In this paper, the A1 target in ICF experiment was produced by single point diamond turning technology. The effect of turning process on the surface roughness of A1 target was discussed. The experiment results have demonstrated that lower surface roughness of A1 target can be fabricated with smaller feed speed and higher spindle rotate speed. The surface roughness was analyzed by means of Form Talysurf device. The result showed that the surface roughness of the aluminum target was less than 50 nm. |
| |
| Keywords: | Single point diamond turning Inertial confinement fusion Aluminum target Surface roughness |
| 本文献已被 CNKI 维普 万方数据 等数据库收录！ |
| 点击此处可从《强激光与粒子束》浏览原始摘要信息 |
|
点击此处可从《强激光与粒子束》下载免费的PDF全文 |
