一维核废料污染问题的一个二阶格式

利用降价法研究了多孔介质中一维核废料污染问题，此模型由一非线性抛物－椭圆耦合偏微分方程组的初边值问题来描述，对此问题给出了一个关于时间和空间均具有二阶精度的差分格式，并进行了理论分析。     

Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

Adsorption Behaviour of 134Cs and 22Na Ions on Tin and Titanium Ferrocyanides

Tin and titanium ferrocyanides were studied as adsorbents for alkali metal ions, viz., ¹³⁴Cs and ²²Na, which represent radioactive wastes. The ferrocyanides were prepared in granular form. The tin version contained 11.2% water, while the titanium version contained 17.7% water. The exchange capacities for Cs⁺ and Na⁺ in the hydrated tin version were about 1.5 and 0.7 meq/g, respectively, while those in the titanium version were 2.2 and 1.2 meq/g, respectively. Drying at 250°C decimated those capacities. The diffusional time constant of Cs⁺ at 25°C, determined via Fick's second law, was of order of magnitude 1 × 10^–3 s^–1, though there were minor differences due to particle size and the form of ferrocyanide. Similarly, the effective diffusivity was of order of magnitude 1 × 10^–8 cm²/s. The titanium version responded slightly faster than the tin version. Likewise, equilibrium measurements in mixtures with sodium nitrate, potassium nitrate, or uranium oxide, showed that the titanium version exhibited significantly greater selectivity for Cs⁺ than did the tin version. Unfortunately, tests of complete elution of the Cs⁺ from the ferrocyanides were mostly disappointing. Work continues on that subject.     

Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

绢纺生产用抗静电剂的研究——SS1与SS2绢纺抗静电剂

本文对绢纺生产用抗静电剂的配方进行了研究,研制出SS1及SS2绢纺抗静电剂。应用表明,采用此类抗静电剂,不但降低了生产中的静电,而且提高了梳折;在圆梳系统中提高了3.23％,在精梳系统中提高了3.1％;同时精绵的长度和强力也有所增加,从而提高了经济效益。     

放射性废物概述

全世界许多国家都在着手于核废物的管理任务．目前，还不能认为这个极其困难的问题在任何国家中真正得到了解答，然而又必须得出解答．本文中概括地说明了有关核废物各方面的常识     

油田含聚废水处理方法研究

介绍了JCS净水剂在油田含聚丙烯酰胺污水处理中的应用、基本工艺流程、最佳投加量以及成本。     

MgO在Mg-hBN体系中对合成cBN晶体的影响

 以金属镁粉为触媒，以六角氮化硼为原料，其中加入适量比例的氧化镁，在国产六面顶压机上，在约5.0 GPa压力、1 500～1 800 K温度条件下，合成出了颜色均匀、晶形完整的黄色立方氮化硼单晶体。实验结果表明，在Mg-hBN体系中，氧化镁对合成cBN晶体的颜色及合成温度有很大的影响。     

高温菌及用于废物处理的研究

论述了高温菌的特点 ,讨论了高温菌在废物处理过程中的应用 ,指出了高温菌用于废物处理系统的优点及不足     

冶炼工业废气中SO_2的脱除研究

研究用软锰矿的水悬浮液脱除冶炼工业废气中SO_2的工艺可行性,提出抑制副产物MnS_2O_6生成的途径。