Effect of pressure on the low-temperature reaction of ethylene with N2O4

Calorimetric monitoring of the autoclave reaction N₂O₄ + C₂H₄ at –85 to +10 °C under argon pressure 10–30 bar revealed that the exothermic chemical reaction started at temperatures above –52 °C at 10 bar, whereas an intensive exothermic reaction started at –85 °C and pressure of 30 bar. IR study showed that oligo/polynitroethylene was formed at 30 bar, while carbonyl and hydroxy compound as well as nitrate R–ONO₂ formation occurred upon processing at 10 bar.     

基于40Cr高温动态力学性能的磨削表面动态再结晶行为

通过分离式霍普金森压杆(SHPB)实验得到了40Cr合金钢在高温高应变率下真应力-真应变曲线，据此确定了材料发生动态再结晶的临界条件.采用解析法和实验法分别求解了磨削强化层的温度场和塑性应变场分布.结果表明，磨削强化层在磨削深度方向具有较大的温度和塑性应变梯度;150μm强化层内会发生奥氏体转变;磨削表面最高温度可达1060℃.在磨削亚表面60μm内会产生剧烈的塑性变形，达到了再结晶的临界条件.较大的磨削深度使磨削强化层塑性应变增大，再结晶现象越充分，微观组织细化程度越高.     

坚硬顶板爆破切顶在沿空留巷中的应用研究

当煤层上方为坚硬顶板时,在工作面回采期间容易出现大面积悬顶,导致巷旁充填体出现大变形破坏,极大威胁采煤安全.为解决这一问题,以某矿1205工作面沿空留巷为工程背景,分析了爆炸围岩裂隙范围和坚硬顶板破断特征,建立了切顶卸压围岩结构力学模型,研究表明,相邻炮孔爆炸后,炮孔间裂隙互相贯穿,降低了顶板强度,同时当切顶角为15°时,巷道稳定性较好.工程实践结果表明:采用爆破切顶技术后,顶板下沉量减小了62.3%,较好地保证了围岩稳定性.     

砂岩在西湖凹陷花港组交互式盖层中的作用初探

西湖凹陷花港组盖层具有砂泥岩交互式发育特征，而与泥岩伴生的砂岩类盖层的油气封闭作用研究较少。采用岩芯、镜下观察及压汞等分析方法，对砂泥岩交互式盖层中的砂岩特征进行了分析。结果表明，盖层中的砂岩可作为有效盖层，砂岩类盖层早期受沉积环境控制，含有较多的泥质而导致早期压实作用较强，加之晚期的黏土矿物转换及胶结物的发育，具备形成良好盖层的条件。在不同地区进行砂岩盖层有效性研究时应以沉积环境为基础，针对不同类型的砂岩进行成岩作用研究，并针对不同类型的砂岩样品进行实验分析以明确砂岩盖层的有效性。     

Synthesis of nano-polycrystalline diamond from glassy carbon at pressures up to 25 GPa

ABSTRACT

Nano-polycrystalline diamond (NPD) with various grain sizes has been synthesized from glassy carbon at pressures 15–25?GPa and temperatures 1700–2300°C using multianvil apparatus. The minimum temperature for the synthesis of pure NPD, below which a small amount of compressed graphite was formed, significantly increased with pressure from ～1700°C at 15?GPa to ～1900°C at 25?GPa. The NPD having grain sizes less than ～50?nm was synthesized at temperatures below ～2000°C at 15?GPa and ～2300°C at 25?GPa, above which significant grain growth was observed. The grain size of NPD decreases with increasing pressure and decreasing temperature, and the pure NPD with grain sizes less than 10?nm is obtained in a limited temperature range around 1800–2000°C, depending on pressure. The pure NPD from glassy carbon is highly transparent and exhibits a granular nano-texture, whose grain size is tunable by selecting adequate pressure and temperature conditions.     

Can a Procedure for the Growth of Single-layer Graphene on Copper be used in Different Chemical Vapor Deposition Reactors?

In the last decade, catalytic chemical vapor deposition (CVD) has been intensively explored for the growth of single-layer graphene (SLG). Despite the scattering of guidelines and procedures, variables such as the surface texture/chemistry of catalyst metal foils, carbon feedstock, and growth process parameters have been well-scrutinized. Still, questions remain on how best to standardize the growth procedure. The possible correlation of procedures between different CVD setups is an example. Here, two thermal CVD reactors were explored to grow graphene on Cu foil. The design of these setups was entirely distinct, one being a “showerhead” cold-wall type, whereas the other represented the popular “tubular” hot-wall type. Upon standardizing the Cu foil surface, it was possible to develop a procedure for cm²-scale SLG growth that differed only by the carrier gas flow rate used in the two reactors.     

为什么要引入溶剂的渗透因子

阐明了引入溶剂渗透因子的必要性,较详细地介绍了两种渗透因子及它们间的关系。     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

含气率对PTS时压力容器内流动与传热的影响

本文对反应堆压力容器紧急安注时的流动与传热特性在1/10的模型上进行了流动可视化、局部传热系数以及混合函数的试验研究。针对三个热冲击敏感区域的部分测点,比较了环腔流速为0.5m/s、安注流速为1～30 m/s时不同含气率对下降环腔内流动与传热特性的影响,得出并分析了不同测点传热系数、混合函数的变化规律。研究结果表明:随着含气率增大,安注流体与环腔流体的混合增强;下降环腔内的含气率对小安注流速时的流动与传热影响显著,而对大安注流速时影响较小。     

压力淬火过程中锗的相结构研究

 应用高压原位差热方法，直接测量了压力下锗的固化参数─—固化温度与过冷度。高压差热信号表明，当压力大于3 GPa时，锗在凝固过程中可能发生结构相变。X射线结构分析表明，在最终的样品中除GeⅠ相外，还形成GeⅢ相和GeⅣ相。