Effect of pressure on the low-temperature reaction of ethylene with N2O4

Calorimetric monitoring of the autoclave reaction N₂O₄ + C₂H₄ at –85 to +10 °C under argon pressure 10–30 bar revealed that the exothermic chemical reaction started at temperatures above –52 °C at 10 bar, whereas an intensive exothermic reaction started at –85 °C and pressure of 30 bar. IR study showed that oligo/polynitroethylene was formed at 30 bar, while carbonyl and hydroxy compound as well as nitrate R–ONO₂ formation occurred upon processing at 10 bar.     

Numerical study on thermal performance of TiO2, Fe3O4 and NiCr/engine oil in an inclined wavy pip

The essential intention of the existing article is to illustrate the effect of wall properties on flow and thermal behavior, through a sinusoidal inclined wavy pipe. To succeed this phenomena we assume a sinusoidal pipe consist of wavy surface, whose walls traveling down to its borders and located at an inclined position, moreover titanium dioxide (TiO₂), ferrosoferric oxide (Fe₃O₄) and nichrome (80% Ni and 20% Cr) are considered as nano-particles and unused engine oil is assumed as a base fluid. The arising mathematical equations for thermal and flow ratio with wall slip impact are solved by mathematica. Also, evaluate graphically the thermal and flow behavior of nanofluids for multi values of solid volume fractions (η), rigidity parameter (M₁), stiffness parameter (M₂), viscous damping parameter (M₃), Grashof number (G_r), slip parameter (β) and heat generation parameter (H) also discuss the streamlines for different values of solid volume fraction.     

Viscoelastic properties of ultrathin polycarbonate films by liquid dewetting

A liquid dewetting method for the determination of the viscoelastic properties of ultrathin polymer films has been extended to study thickness effects on the properties of ultrathin polycarbonate (PC) films. PC films with film thicknesses ranging from 4 to 299 nm were placed on glycerol at temperatures from below the macroscopic glass transition temperature (T_g) to above it with the dewetting responses being monitored. It is found that the isothermal creep results for films of the same thickness, but dewetted at different temperatures can be superposed into one master curve, which is consistent with the fact of PC being a thermorheologically simple material. Furthermore, the results show that the T_g of PC thin films is thickness dependent, but the dependence is weaker than the results for freely standing films and similar to literature data for PC films supported on rigid substrates. It was also found that the rubbery plateau region for the PC films stiffens dramatically, but still less than what has been observed for freely standing polycarbonate films. The rubbery stiffening is discussed in terms of a recently reported model that relates macroscopic segmental dynamics with the stiffening. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1559–1566     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

连续刚构铁路桥收缩徐变效应监测与分析

对连续刚构铁路桥箱梁温度场及桥梁线形进行长期、连续监测,通过主梁跨中下挠的理论与实测对比揭示了连续刚构铁路桥收缩徐变效应。对比了国内外常用收缩徐变估算模型,选择CEB-FIP徐变模型对黄河特大连续刚构桥进行了有限元分析。采用实测温度数据,以箱梁内测温度、外侧温度、顶底板温度梯度、左右侧温度梯度作为箱梁温度场的评判指标,对箱梁1年内的四季温度场分布进行分析。在基于相同温度场的条件下,通过理论值与实测值对比,发现分析成果与实测结果较吻合,说明混凝土的收缩徐变是引起连续刚构铁路桥跨中下挠的主要原因,对比结果还说明通过改善箱梁顶底板应力差能够改善收缩徐变长期效应。     

Morphologically controlled synthesis of 1-dimensional selenium dioxide and study of its application as catalyst for diesel fuel additive

In this research work, selenium dioxide (SeO₂) nanorods have been prepared by a solvothermal method in which a strong reducing agent (NaBH₄) was used to reduce precursor salt into SeO₂ nanorods. X-ray diffraction (XRD) technique was applied to observe the crystal structure which confirmed its tetragonal geometry. Moreover, morphology and particle size were studied by scanning electron microscopy (SEM). SEM fully described the 1-dimensional morphology of SeO₂ nanorods which then arranged themselves to create a 3-dimensional flower-like structure with an average particle size of 50 nm. Also, the catalytic activity of SeO₂ nanorods as diesel-additive was studied by defining different parameters such as fire and flash points, calorific value, cloud and pour points, specific gravity, and kinematic viscosity. Subsequently, SeO₂ nanorods proved to be an excellent diesel additive due to higher total heat content and lower value of kinematic viscosity which enhances the better performance of the diesel engine.     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

110kv及其以下的油浸电力变压器的优化设计

变压器的优化设计是变压器设计的核心,根据变压器自身的特征,通常采用遗传算法进行优化。本系统通过采用改进GA的父代参与竞争的最优保存遗传算法进行优化,得到了几乎必然收敛的优化效果。