页岩气低伤害超临界CO2凝胶压裂液研究

针对常规水压裂液会对页岩造成伤害，容易产生水锁，不易返排，还造成水资源消耗和污染环境等问题，制备了低伤害二氧化碳凝胶压裂液。将自备的F2EU和F4EU增稠剂加入到超临界CO₂基液中，探究两种增稠剂的加入量对CO₂凝胶压裂液黏度的影响，综合考虑成本与效果，优选了2%的F4EU增稠剂，可将CO₂的黏度增至15.4 mPa·s。研究了温度、压力以及剪切速率对凝胶压裂液黏度的影响。实验结果表明，随着温度升高黏度总体降低，但中间出现一个短暂升高阶段；随着压力上升压裂液黏度增加；随着剪切速率的增加压裂液黏度下降，属于一种典型的剪切变稀的假塑性流体。F4EU超临界CO₂凝胶压裂液的平均伤害率为1.39%，远远小于常规压裂液对岩芯的伤害率。实验表明，F4EU超临界CO₂凝胶压裂液在页岩气压裂开采中具有良好的应用前景。     

Supercritical Fluid Carbon Dioxide in the Extraction of Lanolin and Its Alcohol

The use of supercritical fluid carbon dioxide (SF-CO_2) in extraction of lanolin and its alcohol issuperior to the conventional solvent extractionmethod. Its distinctive advantages include highextractive ratio, nontoxic and nonflammablesolvents, and minimal by-product pollution. The     

超临界流体色谱流程设计及其应用

本文设计了多功能超临界流体色谱流程,流程中包括毛细管/微填充柱SFC,GC,计算机控制温度、压力、密度及信号采集、处理,配置有超临界流体萃取池,解决了超临界流体色谱分流口易堵问题。利用该流程,将石腊、DC-200气相色谱固定相、黄油、蜂蜡、救心油、红花油等样品进行超临界流体色谱分离。     

超临界流体触媒作用下石墨-金刚石转变

 研究了超临界流体CO₂在石墨-金刚石转变中的触媒作用。实验中，采用Ag₂O作为流体触媒的先驱材料，在7.7 GPa压力下，Ag₂O在1 200 ℃分解成Ag和O₂，O₂与石墨套管在高温高压下反应形成CO₂超临界流体。研究结果表明，在7.7 GPa和1 500 ℃以上温度条件下，石墨在CO₂流体触媒的作用下可转变为金刚石晶体，在1 500～1 700 ℃温度范围内合成出的金刚石具有完好的八面体形貌，与天然金刚石的生长特征非常相似。     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Continuous reaction system to investigate the dispersion polymerization of vinyl monomers in supercritical carbon dioxide

A laboratory‐scale continuous reaction system using a stirred tank reactor was assembled in our laboratory to study the dispersion polymerization of vinyl monomers in supercritical carbon dioxide (scCO₂). The apparatus was equipped with a suitable downstream separation section to collect solid particles entrained in the effluent stream from the reactor, whose monomer concentration could be measured online with a gas chromatograph. The dispersion polymerization of methyl methacrylate in scCO₂ was selected as a model process to be investigated in the apparatus. The experiments were performed at 65 °C and 25 MPa with 2,2′‐azobisisobutyronitrile as the initiator and a reactive polysiloxane macromonomer as a surfactant to investigate the effect of the mean residence time of the reaction mixture on the monomer conversion, polymerization rate, polymer molecular weight, and particle size distribution. The results were compared with those obtained in batch polymerizations carried out under similar operative conditions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4122–4135, 2006     

Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

Morphologies of microporous polyethylene and polypropylene crystallized from solution in supercritical propane

The morphologies of solvent-free, microporous, mechanically self-supporting cylinders of linear polyethylene and isotactic polypropylene, crystallized from solution in supercritical propane, were examined by an SEM technique. The morphology of gels (or foams), obtained with little or no shrinkage from 2% to 35% solutions by weight of polyethylene (99% to 85% porosities), is shown in some detail. Lamellae with very little or considerable mutual organization occur, often in the form of stacks with straight or coiled axes (axialites). Further growth of these can lead to particles with a roughly spherical overall shape and a predominantly radial orientation of the lamellae at the particle surface. Subcooled isotactic polypropylene, on the other hand, crystallizes in the form of perfectly shaped birefringent microspheres of very uniform size. ©1995 John Wiley & Sons, Inc.