螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

ZnO nanowire lines and bundles: Template-deformation-guided alignment for patterned field-electron emitters

One-dimensional ZnO materials have been promising for field-emission (FE) application, but how to facially control the alignment of ZnO emitters is still a great challenge especially for patterned display application. Here, we report the fabrication of novel ZnO nanowire (NW) line and bundle arrays for patterned field-electron emitters. The effects of PS template size and heating time on the resulted ZnO nanoarrays were systematically studied. The deformation degree of PS templates was controlled and hence utilized to adjust the alignment of electrochemically deposited ZnO arrays. It was found that the length of NW lines and the density of NW bundles can effectively tuned by the PS template heating time. The optimal FE performance with turn-on electric field as low as of 4.4 V μm⁻¹ and the field-enhancement factor as high as of 1450 were achieved through decreasing the screening effect among the patterned field-electron emitters.     

A Structural Entropy Measurement Principle of Propositional Formulas in Conjunctive Normal Form

The satisfiability (SAT) problem is a core problem in computer science. Existing studies have shown that most industrial SAT instances can be effectively solved by modern SAT solvers while random SAT instances cannot. It is believed that the structural characteristics of different SAT formula classes are the reasons behind this difference. In this paper, we study the structural properties of propositional formulas in conjunctive normal form (CNF) by the principle of structural entropy of formulas. First, we used structural entropy to measure the complex structure of a formula and found that the difficulty solving the formula is related to the structural entropy of the formula. The smaller the compressing information of a formula, the more difficult it is to solve the formula. Secondly, we proposed a λ-approximation strategy to approximate the structural entropy of large formulas. The experimental results showed that the proposed strategy can effectively approximate the structural entropy of the original formula and that the approximation ratio is more than 92%. Finally, we analyzed the structural properties of a formula in the solution process and found that a local search solver tends to select variables in different communities to perform the next round of searches during a search and that the structural entropy of a variable affects the probability of the variable being flipped. By using these conclusions, we also proposed an initial candidate solution generation strategy for a local search for SAT, and the experimental results showed that this strategy effectively improves the performance of the solvers CCAsat and Sparrow2011 when incorporated into these two solvers.     

基于三维点云的岩体结构面自动分类与参数计算

结构面间距是岩体稳定性和力学特性分析中的一个重要参数，在岩石力学、采矿工程、边坡监测等领域的数值计算中广泛应用.本文以岩体边坡露头为研究对象，基于非接触测量获得的三维点云数据，提出一种基于密度聚类的结构面细化分类方法；在结构面粗略分组提取的基础上，通过投影变换、散乱点拟合等算法，求得结构面间距和岩体体积节理数.设计开发了结构面细化分类及间距等参数计算与分析原型系统，实际案例分析表明，本文方法可有效实现结构面的自动细化分类，并能够计算出间距等相关参数，可为岩体质量分级和岩体稳定性分析等提供方法支撑.     

氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

固体力学有限元体系的结构拓扑变化理论

本文是文[1]的继续.文[1]提出了杆件系统的结构拓扑变化理论和拓扑变化法本文将这一理论和方法推进到连续体有限元体系;且在此基础上揭示出有限元体系的一个新性质,称为基本位移之梯度的正交性定理,从而给出一套设计敏度的显式表达式,可直接用于计算.     

加肋圆柱壳在轴压作用下的屈曲和后屈曲

本文讨论完善和非完善的,纵向加肋和正交加肋圆柱壳在轴压作用下的屈曲和后屈曲性态.依据文[1]提供的圆柱薄壳屈曲的边界层理论及其分析方法,给出了加肋圆柱壳在轴压作用下的屈曲和后屈曲理论分析.本文同时讨论肋骨与壳板材料不同时对加肋圆柱壳屈曲和后屈曲性态的影响.