螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

ZnO nanowire lines and bundles: Template-deformation-guided alignment for patterned field-electron emitters

One-dimensional ZnO materials have been promising for field-emission (FE) application, but how to facially control the alignment of ZnO emitters is still a great challenge especially for patterned display application. Here, we report the fabrication of novel ZnO nanowire (NW) line and bundle arrays for patterned field-electron emitters. The effects of PS template size and heating time on the resulted ZnO nanoarrays were systematically studied. The deformation degree of PS templates was controlled and hence utilized to adjust the alignment of electrochemically deposited ZnO arrays. It was found that the length of NW lines and the density of NW bundles can effectively tuned by the PS template heating time. The optimal FE performance with turn-on electric field as low as of 4.4 V μm⁻¹ and the field-enhancement factor as high as of 1450 were achieved through decreasing the screening effect among the patterned field-electron emitters.     

磁流变液中磁性颗粒成链与团聚的临界特征分析

热运动对纳米级磁流变液系统的颗粒团聚行为和宏观流变特性扰动影响不可忽视.为研究施加外磁场后系统微结构与热运动间的关系，探讨在不同颗粒粒径情况下热运动能量在系统总能量中的占比.采用CCD设计方法，分析Monte Carlo仿真获取的颗粒位形信息，生成关于外磁场磁感应强度、颗粒粒径和体积分数的系统热耦合系数<λ>回归模型;成链团聚的临界颗粒粒径计算值比文献经验值高出约23%，证实在考虑系统内多因素的综合影响下，纳米级磁流变液具有更严格的流变现象临界发生条件.     

基于热中子探测评价裂缝的示踪剂特性研究

针对裂缝热中子示踪探测方法,从中子双组扩散理论入手结合蒙特卡洛数值模拟方法,分析压裂前后地层热中子分布影响因素,并模拟不同类型示踪剂及含量的热中子裂缝响应规律,筛选最佳示踪剂并给出其在支撑剂中含量的上、下限。结果表明:压裂前后热中子计数变化量主要受裂缝宽度和标记支撑剂中示踪剂含量的影响;钆对裂缝宽度变化反应最灵敏,钆元素是作为标记支撑剂的最佳示踪元素;随支撑剂中Gd 2O 3含量的增加,热中子计数率降低,热中子计数变化量D增加;示踪剂中氧化钆的上、下限值随裂缝宽度呈指数降低,且当裂缝宽度为1.0 cm时,Gd 2O 3的质量分数上限为0.68%,下限为0.03%。     

Fracture behavior and mechanical,thermal, and rheological properties of biodegradable films extruded by flat die and calender

The development of biodegradable materials for tailored applications, particularly in the field of polymeric films and sheets, is a challenging technological goal as well as a contribution to help protect the environment. Poly(lactic) acid (PLA) is a promising substitute for several oil-based polymers; however, to overcome its thermal and mechanical drawbacks, researchers have developed solutions such as blending PLA with polybutylene adipate terephthalate (PBAT), which is capable of increasing the ductility of the final material. In this study, PLA/PBAT binary blends, with minimum possible content of nonrenewable materials, were examined from processing, thermal, morphological, and rheological perspective. An optimized PLA/PBAT ratio was chosen as the polymeric basis to obtain a biodegradable formulation by adding a biobased plasticizer and appropriate fillers to produce a micrometer film with tailored flexibility and tear resistance. The processing technology involved flat-die extrusion, followed by calendering. The tearing resistance of the produced film was investigated, and the results were compared with literature data. A study on the essential work of fracture was implemented to explore the mode III out-of-plane fracture resistance starting from a trouser tear test.     

高速电主轴热特性仿真与实验研究

对高速电主轴温度场分布随转速的变化规律进行了研究。通过在外壳上布置一定数量的温度传感器,对不同转速下的外壳温度进行实时测量,并将实验结果与ANSYS的模拟结果进行对比,验证了采用在电主轴外壳上布置多个测点测量与仿真相结合的方法来预测电主轴内部温度场分布的可行性;另外还分析了在不同转速下,高速电主轴关键部位的温升,仿真结果表明:主轴在6000~10000 r/min时,温升呈线性增加,在大于10000 r/min后,温升以指数规律增加。     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

Experimental and Theoretical Mechanistic Study on the Thermal Decomposition of 3,3-diphenyl-4-(trichloromethyl)-5-nitropyrazoline

The present paper is a continuation of comprehensive study regarding to synthesis and properties of pyrazoles and their derivatives. In its framework an experimental and theoretical studies of thermal decomposition of the 3,3-diphenyl-4-(trichloromethyl)-5-nitropyrazoline were performed. It was found, that the decompositions of the mentioned pyrazoline system in the solution and at the melted state proceed via completely different molecular mechanisms. These mechanisms have been explained in the framework of the Molecular Electron Density Theory (MEDT) with the computational level of B3LYP/6-31G(d). A Bonding Evolution Theory (BET) examination of dehydrochlorination of the 3,3-diphenyl-4-(trichloromethyl)-5-nitropyrazoline permits elucidation of the molecular mechanism. It was found, that on the contrary for most known HCl extrusion processes in solution, this reaction is realised via single-step mechanism.