基于修正斜压场的RC框架边节点剪切性能分析

为研究钢筋屈服强度和混凝土抗压强度对钢筋混凝土(RC)框架边节点剪切性能的影响规律,基于修正斜压场理论(MCFT),对某框架边节点的剪切应力-应变骨架曲线进行数值模拟,并与试验结果进行对比.在验证MCFT算法的精度后,研究钢筋屈服强度和混凝土抗压强度两个参数变化对RC框架边节点剪切应力-应变骨架曲线和峰值剪切应力的影响规律.结果表明:基于MCFT可以较好地模拟RC框架边节点的剪切应力-应变关系曲线; RC框架边节点的峰值剪切应力对混凝土抗压强度的变化更为敏感,但当试件的钢筋(HRB400)屈服应力下降幅度超过16.45%时,对钢筋屈服应力的变化更为敏感;当试件的钢筋(HRB400)屈服应力下降幅度超过10%时,节点发生钢筋滑移破坏,此时峰值剪切应力会大幅下降.     

非锚固式大型立式热质储罐强度分析

针对大型储罐在多种载荷作用下易发生强度破坏的问题，以某热质储罐为研究对象，利用有限元法分析热质储罐在自重、内压、液柱静压力、风载荷、地震载荷、雪载荷以及温度载荷作用下的应力强度以及变形，模拟大角焊缝区域翘曲情况，并依照JB4732—1995进行强度评定，为此类大型立式储罐的设计提供参考。     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

矩形型钢弯曲回弹曲率半径r值的确定

文章在分析矩形型钢弯曲变形过程及应力与应变等方面的关系的基础上，推导出工件曲率半径与工件回弹后曲率半径之间的关系，从而确定了凸模半径。     

地下洞室形状优化设计

洞室开挖会使围岩周边产生应力集中 ,产生拉应力与压应力。围岩出现拉应力对洞室稳定十分不利 ,通常通过改变洞室形状和轴比来消除围岩中的拉应力。本文提出一种使洞室拉应力σθ=0 ,而压应力最小的确定洞室最优几何形状的方法。     

AGE method simulations of a turbulent far‐wake compared to spectral DNS

Turbulent flow simulation methods based on finite differences are attractive for their simplicity, flexibility and efficiency, but not always for accuracy or stability. This paper demonstrates that a good compromise is possible with the advected grid explicit (AGE) method. Starting from the same initial field as a previous spectral DNS, AGE method simulations of a planar turbulent wake were carried out as DNS, and then at three levels of reduced resolution. The latter cases were in a sense large‐eddy simulations (LES), although no specific sub‐grid‐scale model was used. Results for the two DNS methods, including variances and power spectra, were very similar, but the AGE simulation required much less computational effort. Small‐scale information was lost in the reduced resolution runs, but large‐scale mean and instantaneous properties were reproduced quite well, with further large reductions in computational effort. Quality of results becomes more sensitive to the value chosen for one of the AGE method parameters as resolution is reduced, from which it is inferred that the numerical stability procedure controlled by the parameter is acting in part as a sub‐grid‐scale model. Copyright © 2002 John Wiley & Sons, Ltd.     

钢板仓受风载作用的有限元分析

对高 14.76m ,直径 12m的螺旋卷边钢板筒仓在空仓风载工况下进行了有限元分析。计算结果表明 ,在风载作用下 ,仓体的强度不是主要问题 ,而仓顶开口处刚度较弱。     

结合梁剪力连接件剪拔受力的非线性分析

探讨了结合梁剪力连接件在复杂受力情况下的非线性分析模式与分析方法，计算结果与剪拔试验模型实测结果吻合良好。在此基础上，计算了广州内环中山一路结合梁剪力连接件的受力行为，为设计单位提供了设计参数。     

Stress Distribution in an Infinite Elastic Body with a Locally Curved Fiber in a Geometrically Nonlinear Statement

Within the framework of a piecewise homogeneous body model, with the use of three-dimensional geometrically nonlinear exact equations of elasticity theory, a method for determining the stress—strain state in unidirectional fibrous composites with locally curved fibers is developed for the case where the interaction between the fibers is neglected. All the investigations are carried out for an infinite elastic body containing a single locally curved fiber. Numerical results illustrating the effect of geometrical nonlinearity on the distribution of the self-balanced normal and shear stresses acting on the interface and arising as a result of local curving of the fiber are presented.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 433–448, July–August, 2005.