Interface and defects engineering for multilayer laser coatings

High-reflective multilayer laser coatings are widely used in advanced optical systems from high power laser facilities to high precision metrology systems. However, the real interface quality and defects will significantly affect absorption/scattering losses and laser induced damage thresholds of multilayer coatings. With the recent advances in the control of coating design and deposition processes, these coating properties can be significantly improved when properly engineered the interface and defects. This paper reviews the recent progress in the physics of laser damage, optical losses and environmental stability involved in multilayer reflective coatings for high power nanosecond near-infrared lasers. We first provide an overview of the layer growth mechanisms, ways to control the microstructures and reduce layer roughness, as well as the nature of defects which are critical to the optical loss and laser induced damage. Then an overview of interface engineering based on the design of coating structure and the regulation of deposition materials reveals their ability to improve the laser induced damage threshold, reduce the backscattering, and realize the desirable properties of environmental stability and exceptional multifunctionality. Moreover, we describe the recent progress in the laser damage and scattering mechanism of nodule defects and give the approaches to suppress the defect-induced damage and scattering of the multilayer laser coatings. Finally, the present challenges and limitations of high-performance multilayer laser coatings are highlighted, along with the comments on likely trends in future.     

Strain induced strengthening of soft thermoplastic polyurethanes under cyclic deformation

We investigate the cyclic mechanical behavior in uniaxial tension of three different commercial thermoplastic polyurethane elastomers (TPU) often considered as a sustainable replacement for common filled elastomers. All TPU have similar hard segment contents and linear moduli but sensibly different large strain properties as shown by X-ray analysis. Despite these differences, we found a stiffening effect after conditioning in step cyclic loading which greatly differs from the common softening (also referred as Mullins effect) observed in chemically crosslinked filled rubbers. We propose that this self-reinforcement is related to the fragmentation of hard domains, naturally present in TPU, in smaller but more numerous sub-units that may act as new physical crosslinking points. The proposed stiffening mechanism is not dissimilar to the strain-induced crystallization observed in stretched natural rubber, but it presents a persistent nature. In particular, it may cause a local reinforcement where an inhomogeneous strain field is present, as is the case of a crack propagating in cyclic fatigue, providing a potential explanation for the well-known toughness and wear resistance of TPU.     

页岩气低伤害超临界CO2凝胶压裂液研究

针对常规水压裂液会对页岩造成伤害，容易产生水锁，不易返排，还造成水资源消耗和污染环境等问题，制备了低伤害二氧化碳凝胶压裂液。将自备的F2EU和F4EU增稠剂加入到超临界CO₂基液中，探究两种增稠剂的加入量对CO₂凝胶压裂液黏度的影响，综合考虑成本与效果，优选了2%的F4EU增稠剂，可将CO₂的黏度增至15.4 mPa·s。研究了温度、压力以及剪切速率对凝胶压裂液黏度的影响。实验结果表明，随着温度升高黏度总体降低，但中间出现一个短暂升高阶段；随着压力上升压裂液黏度增加；随着剪切速率的增加压裂液黏度下降，属于一种典型的剪切变稀的假塑性流体。F4EU超临界CO₂凝胶压裂液的平均伤害率为1.39%，远远小于常规压裂液对岩芯的伤害率。实验表明，F4EU超临界CO₂凝胶压裂液在页岩气压裂开采中具有良好的应用前景。     

干燥工艺对稻谷发芽率影响的研究

利用薄层干燥试验台，采用二次回归正交组合设计试验对辽宁省稻谷主要品种942进行研究。分析了热风温度、表现风速、初始水分、干燥时间对稻谷发芽率损失影响的规律，建立了稻谷发芽率损失回归方程，在干燥时应采用低温干燥，以保证其发芽率。利用贡献率法确定各因素在二次非线性模型中的主次关系为热风温度、初始水分、表现风速、干燥时间，为进行辽宁省稻谷深床干燥研究提供了理论依据。     

单甲基原位改性SiO2疏水减反膜的制备与性能研究

 在碱性条件下通过TEOS和MTES的共水解缩聚反应制备了单甲基原位改性的SiO₂溶胶，并使用提拉法在K9玻璃基片上镀制了疏水减反膜。通过透射电镜（TEM）考察了镀膜溶胶的微结构，分别使用红外光谱（FTIR）分析了薄膜的组分，用原子力显微镜（AFM）观察了薄膜的表面形貌和起伏状况，用紫外可见光谱（UV-vis）考察了薄膜的减反射性能，用接触角仪测量了薄膜对水的接触角。并使用“R-on-1”的方式测量了薄膜在Nd:YAG激光（1 064 nm，1 ns）作用下的损伤阈值。结果表明，通过共水解缩聚反应可以把甲基引入镀膜溶胶簇团中，改善了溶胶簇团的网络结构，使薄膜得到相当好的疏水性能和更好的抗激光损伤性能，同时薄膜能保持较好的减反射性能。     

Laser-induced damage of Ta2O5/SiO2 narrow-band interference filters under different 1064 nm Nd:YAG laser modes

The laser-induced damage (LID) behavior of narrow-band interference filters was investigated with a Nd:YAG laser at 1064 nm under single-pulse mode and free-running mode. The absorption measurement of such coatings was performed with surface thermal lensing (STL) technique. The damage morphologies under the two different laser modes were also studied in detail. It was found that all the filters exhibited a pass-band-center-dependent absorption and laser-induced damage threshold (LIDT) behavior, but the damage morphologies were diverse. The explanation was given with the analysis of the electric field distribution and the operational behavior of the irradiation laser.     

Decreasing the Displacements of a Composite Saddle-Shaped Cable Roof

The structural possibilities of decreasing the compliance of a composite saddle-shaped cable roof having a compliant support contour are investigated. The use of a supporting contour consisting of cables joined together with tie-bars is considered as a structural method enabling one to decrease the compliance of the roof. Each cable of the support has its own initial flexure. The method is most efficient from the viewpoint of material consumption per unit of covered area relative to the increasing rigidity and prestress level of the cable net.The efficiency of the method was evaluated by a numerical experiment, which was carried out for a composite saddle-shaped cable roof 50 × 50 m in the plan. The roof was formed by two orthogonal cable groups joined with a compliant supporting contour. A hybrid composite cable based on a carbon-fiber-reinforced plastic, a glass-fiber-reinforced plastic, and steel was considered as a material for the cable net in combination with steel. The material consumption and the maximum vertical displacement of the cable net in relation to the initial geometrical characteristics of the supporting contour were obtained. A possibility of decreasing the maximum vertical displacements of the roof by 8% was established.     

注浆覆岩离层力学机理及其离层发育分类研究

依据覆岩离层生成的力学机理,结合煤层开采程度的不同,将可注浆层位的离层划分为三类.以岩石的应变为指标,确立了覆岩离层可注浆层位岩梁的断裂步距表达式,理论上证明了划分注浆层位的合理性.根据岩石的全应力应变试验,结合现场实际观测数据,对以应变为指标的岩梁断裂步距表达式做了初步验证.结果表明:可注浆层位的分类和断裂步距表达式的确定对注浆减沉工程具有指导意义.     

激光诱导间质肿瘤热疗的数值模拟和实验研究

本文在考虑生物组织物性动态变化的情况下建立了激光诱导间质肿瘤热疗(LITT)的物理数学模型,采用MonteCarlo方法数值模拟了LITT中激光能量在生物组织内的传输过程,基于Pennes生物传热方程和Arrhenius方程数值求解了组织内的温度分布和热损伤体积的变化,分析了热物性及血液灌注率的动态变化对LITT过程的影响,并与相应的离体实验结果进行了对比。数值模拟结果表明,组织的热物性及血液灌注率的动态变化对于热损伤体积的变化具有重要的影响。因此在激光诱导间质肿瘤热疗的数值模拟中应该考虑热物性及血液灌注率的动态变化以期为临床治疗方案的制定提供更为准确的依据。     

ns脉冲激光对K9玻璃的破坏实验

 采用高速PIN光电探测器和高带宽的数字存储示波器，实时检测透射光脉冲和散射光脉冲的变化特征，并将之用作材料破坏的光学判据，测量得到K9玻璃在1.06μm纳秒脉冲激光作用下的能量损伤阈值约18mJ，相应的能量密度阈值为1.0kJ/cm²。通过分析透射光脉冲和散射光脉冲的特征，给出了材料的破坏时刻，并推断出K9玻璃所能承受的极限光强为10¹⁵W/m²。研究了能量透过率与泵浦能量的关系，并初步探讨了透明材料的破坏机理。结果表明：在多纵模激光的作用下，透明光学材料破坏是电离击穿与自聚焦效应综合作用的结果。