轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

冷轧带钢局部高点卷取过程起筋控制的建模与仿真

为了研究带钢局部高点卷取起筋的控制方法，利用三维弹塑性变形基本理论，并引入带钢塑性流动因子，建立了弹塑性卷取应力和起筋量模型.基于应力函数假设、S. Timoshenko最小功原理和伽辽金虚位移法建立了起筋带钢的应力场分布和可用于在线计算的起筋临界卷取张力设定模型.仿真结果表明：局部高点在径向累积叠加所引起的带钢张力不均匀分布和轴向压应力是导致带钢起筋的主要原因；起筋量随局部高点高度、卷径和卷取张力增加而增大，薄带钢比厚带钢起筋量增幅明显；临界卷取张力随卷径、带钢厚度和局部高点高度增大而减小.     

异步轧机轧辊稳定性的探讨

本文通过对异步轧制特点的分析,求出中性角及力能参数间的关系,从而导出了不同工作制度下的异步轧机工作辊偏移值的计算公式。本文结论将对改造现有轧机和设计新轧机提供理论依据。     

集成有源负载放大器的研究

本文重点介绍了集成有源负载放大器的分析方法,并以镜像电流源为例详细介绍、对比了两种方法(图解分析法和微变等效电路分析法)。此外,介绍了用厄雷电压计算 Av 的简便方法。     

滚动实验的另一种演示

介绍了另一种滚动演示实验,并对演示结果进行了理论分析和解释     

六台轧机热轧钢板在线测长及产品统计微机系统

本论文选用Apple-Ⅱ作主机,开发了一套外设接口扩展箱和相应的应用软件,用于实现在钢厂中对六台单轧机的热轧钢板长度在线检测和现场显示,同时对钢板的长度按照合格、超长、超短进行分类统计,打印生产报表。此外还提供随时修改钢板长度(标尺)设定值和随机查询各台轧机产质量状况的功能。在接口扩展箱中,采用了包括光电耦合在内的若干抗干扰措施,保证系统能在钢厂恶劣环境中正常运行。本系统已在工厂轧机上试用成功。     

Variational Derivative for Buckling Loads of Beams and Frames

The finite-difference method is a numerical technique for obtaining approximate solutions to differential equations. The main objective of the present study is to give a new aspect to the finite-difference method by using a variational derivative. By applying this formulation, accurate values of the buckling loads of beams and frames with various end supports are obtained. The performance of this formulation is verified by comparison with numerical examples in the literature __________ Published in Prikladnaya Mekhanika, Vol. 41, No. 7, pp. 139–144, July 2005.     

Stability and Nonlinear Deformation of Cylindrical Grids

The general stability of single-layer cylindrical grids is studied in linear and nonlinear formulations. Dependence of the general buckling load on the geometry and stiffness parameters of a grid is established in an analytical form. Such grids are numerically analyzed for stability. It is established that the general buckling load is much less than the local buckling load. Typical general buckling modes are found. It is shown that such grids are weakly sensitive to imperfections     

几何相似体应力-应变分布相同时的载荷关系

为了保证几何相似模型与原件具有完全相同的应力-应变分布,必须对几何相似模型施加与实际构件成对应比例的各种载荷,因此需要寻求几何相似模型在应力-应变分布完全相同时各种外加载荷的比例关系。从相似理论入手,以2端固支的矩形梁下表面边线中点的应力解析表达式为基础进行推导,得出相应的理论载荷关系,并用算例在弹塑性状态下验证了所得关系的正确性。得到的结论是:对于2个几何相似构件,若几何相似系数为kl,则当外加集中载荷的载荷系数为kl、均布线载荷的载荷系数为kl、均布面载荷的载荷系数为1时,2构件的应力-应变分布完全相同。     

A parallel cell‐based DSMC method on unstructured adaptive meshes

A parallel DSMC method based on a cell‐based data structure is developed for the efficient simulation of rarefied gas flows on PC‐clusters. Parallel computation is made by decomposing the computational domain into several subdomains. Dynamic load balancing between processors is achieved based on the number of simulation particles and the number of cells allocated in each subdomain. Adjustment of cell size is also made through mesh adaptation for the improvement of solution accuracy and the efficient usage of meshes. Applications were made for a two‐dimensional supersonic leading‐edge flow, the axi‐symmetric Rothe's nozzle, and the open hollow cylinder flare flow for validation. It was found that the present method is an efficient tool for the simulation of rarefied gas flows on PC‐based parallel machines. Copyright © 2004 John Wiley & Sons, Ltd.