Calcium-based coordination polymers from a solvothermal synthesis of HKUST-1 in 3D printed autoclaves

A mixed-metal 1D coordination polymer [CaCu(HBTC)₂(H2O)₈]_n (where H₃BTC – benzene-1,3,5-tric arboxylic acid) was obtained in a solvothermal synthesis of a well-known copper-containing metal–organic framework [Cu₃(BTC)₂(H₂O)₃]_n (HKUST-1) in autoclaves 3D-printed from commercial polypropylene. This material was a source of calcium ions, apparently, leaking from a colorant (calcium carbonate) promoted by glacial acetic acid as a modulator used to produce large single crystals of HKUST-1. This finding was confirmed by elemental analysis and a model experiment that resulted in a new calcium-based 1D coordination polymer [Ca(H₂BTC)₂(H₂O)₅]_n under the same solvothermal conditions with no copper or calcium salts put into a 3D-printed autoclave.     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

Studies on the Crystallization Properties and Morphology Structure of the Cationic Dyeable Polypropylene Fibers

The crystallization properties and morphology structure of the cationic dyeable polypropylene fibers which were produced by the blending spinning method were studied by making use of X-ray and scanning electron microscopy (SEM). It comes to the conclusions that the larger the crystallite size in the fibers is , the better the dycable properties of the fibers are and there is a little compatibility between the dyeable agent and polypropylene resin. And the dye-uptake of the fibers may be up to 90% because the dyeable agent can uniformly be scattered in polypropylene.     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004     

Solvent‐ and interface‐induced surface segregation in blends of isotactic polypropylene with poly(ethylene‐co‐propylene) rubber

The surface compositions and morphologies of melt‐quenched blends of isotactic polypropylene (iPP) with aspecific poly(ethylene‐co‐propylene) rubber (aEPR) were characterized by atomic force microscopy, optical microscopy, and X‐ray photoelectron spectroscopy. The surface morphologies and compositions formed in the melt are frozen‐in by crystallization of the iPP component and, depending on the processing conditions, are enriched in iPP or aEPR or contain a phase‐separated mix of iPP and aEPR. Enrichment of iPP is observed for blends melted in open air, in agreement with earlier work showing the high surface activity of atactic polypropylene at open interfaces. Surface segregation of iPP is suppressed at confined interfaces. Blends melt‐pressed between hydrophilic and hydrophobic substrates have phase‐separated iPP and aEPR domains present at the surface, which grow in size as the melt time increases. Surface enrichment of aEPR is observed after exposing melt‐pressed blends to n‐hexane vapor, which preferentially solvates aEPR and draws it to the surface. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 421–432, 2004     

Structure,morphology, and crystallization process of isotactic polypropylene/hydrogenated hydrocarbon resin blends

The structure, morphology, and isothermal and nonisothermal crystallization of isotactic polypropylene/low‐molecular‐mass hydrocarbon resin blends (iPP/HR) (up to 20% in weight of HR) have been studied, using optical and electron microscopy, wide‐ and small‐angle X‐ray and differential scanning calorimetry. New structures and morphologies can be activated, using appropriate preparation and crystallization conditions and blend composition. For every composition and crystallization condition, iPP crystallizes in α‐form, with a spherulitic morphology. The size of iPP spherulites increases with resin content, whereas the long period decreases. In the range of crystallization temperatures investigated, HR modifies the birefringence of iPP spherulites, favoring the formation of radial lamellae and changing the ratio between tangential and radial lamellae. Spherulitic radial growth rates, overall crystallization rates, and melting temperatures are strongly affected by resin, monotonically decreasing with resin content. This confirms miscibility in the melt between the two components of the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3368–3379, 2004     

High power CW solid-state multilaser system

A laser system containing four CW Nd:YAG double-rod lasers, transforming optics and a fibre with input-output optics has been designed and investigated. It is shown that reduction of the beam parameter product of the non-Gaussian beams in the image space of the lens has made it possible to collect the emission of four lasers to the same fibre. Independent laser operation has provided the output power control in the range of 10–900 W with a stable light spot size on the input end of the fibre.     

罗丹明B光纤酸度传感器的研究

本文采用静电吸附方法将罗丹明B固定在Nafion膜上,制成光纤酸度传感器,具有响应迅速,稳定性良好,干扰少的优点,可用于2～8M硫酸和盐酸的连续监测。     

An optical fibre pH sensor based on dye doped mesostructured silica

This paper describes the synthesis and optical pH sensing properties of a pH indicator dye activated mesostructured silica coated optical fibre. The pH-sensitive dye bromothymol blue was incorporated into the mesostructure sol precursor and thin films/coatings were used for pH-sensing applications without prior removal of the surfactant. The pH sensitivity range and operating wavelength were analysed by absorption measurements on layer dip-coated on glass slides. The pH sensing properties of coated optical fibre were tested by evanescent wave method. Experiments were carried out by using a series of solutions of known pH. No leaching was observed (except at very high pH) and an excellent reversibility was obtained between pH=2 and 5.     

Low noise double pass L-band erbium-doped fiber amplifier

A new double pass long wavelength band erbium-doped fiber amplifier with enhanced noise figure characteristics is demonstrated. The noise figure is improved by about 2.6 dB with the incorporation of broadband conventional-band fiber Bragg grating (FBG) in between the two segments of erbium-doped fiber. By incorporating both the pre-amplifier and the FBG, the noise figure is further improved, which varies from 4.0 to 5.0 dB in the flat gain region from 1570 to 1600 nm. The gain varies from 32.0 to 33.4 dB within this region. The new amplifier with high gain and low noise figure can be useful as an inline amplifier in a wavelength division multiplexing transmission system.