Skyrmion transport driven by pure voltage generated strain gradient

The magnetic skyrmion transport driven by pure voltage-induced strain gradient is proposed and studied via micromagnetic simulation. Through combining the skyrmion with multiferroic heterojunction, a voltage-induced uniaxial strain gradient is adjusted to move skyrmions. In the system, a pair of short-circuited trapezoidal top electrodes can generate the symmetric strain. Due to the symmetry of strain, the magnetic skyrmion can be driven with a linear motion in the middle of the nanostrip without deviation. We calculate the strain distribution generated by the trapezoidal top electrodes pair, and further investigate the influence of the strain intensity as well as the strain gradient on the skyrmion velocity. Our findings provide a stable and low-energy regulation method for skyrmion transport.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

Norbornene derivatives from a metal‐free,strain‐promoted cycloaddition reaction: New building blocks for ring‐opening metathesis polymerization reactions

The preparation of new ring opening metathesis polymerization (ROMP) monomers using a 1,3‐dipolar cycloaddition between aryl azides and norbornadiene is described. Various norbornenetriazolines, obtained through a solvent‐and catalyst‐free reaction, can subsequently be incorporated into polymer backbones through ROMP reactions. Furthermore, thermal decomposition of the triazoline moiety can allow for further polymer functionalization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2357–2362     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

矩形型钢弯曲回弹曲率半径r值的确定

文章在分析矩形型钢弯曲变形过程及应力与应变等方面的关系的基础上，推导出工件曲率半径与工件回弹后曲率半径之间的关系，从而确定了凸模半径。     

用增量有限元法计算金属流动

利用增量有限元理论 ,对金属材料的变形过程进行模拟。为了模拟工程中塑性变形较大的构件的变形规律 ,在每个加载步迭代完成后自动实现坐标更新。     

Comparison of growth stress measurements with modelling in thin iron oxide films

High temperature oxidation of metals leads to residual stresses both in the metal and in the growing oxide. In this work, the evolution of this residual stresses is theoretically predicted in the growing oxide layers. The origin of these stresses is based on a microstructural model. Using experimental results providing from the oxidation kinetics, and an analysis proposed to describe the growth strain occurring in the thin layers, a set of equations is established allowing determining the stresses evolution with oxidation time. Then, the model is compared with experimental results obtained on both α-Fe and phosphated α-Fe, oxidised at different temperatures. Numerical data are extracted from experiments either with an asymptotic formulation or with an inverse method. These two methods give good agreement with experiments and allow extracting the model parameters.     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

注浆覆岩离层力学机理及其离层发育分类研究

依据覆岩离层生成的力学机理,结合煤层开采程度的不同,将可注浆层位的离层划分为三类.以岩石的应变为指标,确立了覆岩离层可注浆层位岩梁的断裂步距表达式,理论上证明了划分注浆层位的合理性.根据岩石的全应力应变试验,结合现场实际观测数据,对以应变为指标的岩梁断裂步距表达式做了初步验证.结果表明:可注浆层位的分类和断裂步距表达式的确定对注浆减沉工程具有指导意义.