Polymer 4D printing: Advanced shape-change and beyond

4D printing is an exciting branch of additive manufacturing. It relies on established 3D printing techniques to fabricate objects in much the same way. However, structures which fall into the 4D printed category have the ability to change with time, hence the “extra dimension.” The common perception of 4D printed objects is that of macroscopic single-material structures limited to point-to-point shape change only, in response to either heat or water. However, in the area of polymer 4D printing, recent advancements challenge this understanding. A host of new polymeric materials have been designed which display a variety of wonderful effects brought about by unconventional stimuli, and advanced additive manufacturing techniques have been developed to accommodate them. As a result, the horizons of polymer 4D printing have been broadened beyond what was initially thought possible. In this review, we showcase the many studies which evolve the very definition of polymer 4D printing, and reveal emerging areas of research integral to its advancement.     

Calcium-based coordination polymers from a solvothermal synthesis of HKUST-1 in 3D printed autoclaves

A mixed-metal 1D coordination polymer [CaCu(HBTC)₂(H2O)₈]_n (where H₃BTC – benzene-1,3,5-tric arboxylic acid) was obtained in a solvothermal synthesis of a well-known copper-containing metal–organic framework [Cu₃(BTC)₂(H₂O)₃]_n (HKUST-1) in autoclaves 3D-printed from commercial polypropylene. This material was a source of calcium ions, apparently, leaking from a colorant (calcium carbonate) promoted by glacial acetic acid as a modulator used to produce large single crystals of HKUST-1. This finding was confirmed by elemental analysis and a model experiment that resulted in a new calcium-based 1D coordination polymer [Ca(H₂BTC)₂(H₂O)₅]_n under the same solvothermal conditions with no copper or calcium salts put into a 3D-printed autoclave.     

三维打印器件后处理液研究

分析了不同的填充强化剂(后处理A液)、不同的后处理B液基料、后处理B液中水性环氧乳液的掺量及后处理液浸泡时间对石膏基打印器件耐水性、抗压强度、尺寸偏差、表面微观结构的影响.结果表明:经纳米硅超硬固化剂处理后的打印器件抗压强度大幅提高,纳米硅超硬固化剂最适宜作为后处理A液;水性聚氨酯乳液PU-202B最适宜作为后处理B液的基料;后处理B液中加入水性环氧乳液,处理后打印器件的抗压强度增加、吸水率降低,但水性环氧乳液含量增加到一定程度后会出现尺寸偏差;后处理A、B液最佳浸泡时间分别为130 s和35 s;先浸泡后处理A液、后浸泡后处理B液的打印器件具有抗压强度高、吸水率小、表面较光滑、不脱粉等优良性能.     

浅谈网络环境下印刷型文献的主体地位

章分析了印刷献在规模数量、学术价值、检索利用等方面的优势，阐述了印刷型献在网络环境下图书馆馆藏中的主体地位。     

代数方法在C语言图形打印问题中的应用

介绍了C语言程序设计中的难点问题——图形打印问题的解决方案，详细论述了如何利用代数方法来解决这一双重循环问题的具体措施。     

Fabrication of patterned gold electrodes with spin-coated-and-fired Au(1 1 1) film by the soft lithography

We prepared high quality Au(1 1 1) film on Si wafer through the spin coating and thermal decomposition of a gold ink, spin-coated-and-fired (SCAF) Au film. The X-ray measurements, XRD and pole-figure analysis, showed that the SCAF Au film has a (1 1 1) out-of-plane orientation with a random in-plane orientation. In order to confirm the chemical activity of the SCAF Au film, we demonstrate the formation of patterned structures with the film by using soft lithography technique. The chemical activities of this physically stable SCAF Au film to the alkanethiols were at least equivalent those of physically deposited the Au films. The possibility of the mass production of micro patterned structure with the SCAF Au film was also demonstrated over the wide region on Si wafer by the microcontact lithography. These suggest that the Au film will help the easy fabrication of various nanosized devices on Si wafer and other substrates.     

AgCl膜光催化降解色素的研究

利用AgCl膜在不同波长光照条件下对水溶液中的5种有机色素进行催化降解实验．实验结果表明，30min内，5种色素(质量浓度为20mg/L)均得到迅速光解，且在太阳光光照条件下AgCl膜具有非常高的光催化性能．并进一步研究了成膜原料液的浓度对光解率的影响、溶液初始质量浓度与光解速率的关系及悬浮态AgCl的光催化对比实验．     

磷酸锌制备实验的改进探索

采用微波加热法和普通加热法制备磷酸锌,微波法具有更快速方便等特点.     

Microstructure array on Si and SiOx generated by micro-contact printing, wet chemical etching and reactive ion etching

A method, combining micro-contact printing (μCP), wet chemical etching and reactive ion etching (RIE), is reported to fabricate microstructures on Si and SiOx. Positive and negative structures were generated based on different stamps used for μCP. The reproducibility of the obtained microstructures shows the methodology reported herein could be useful in Micro-Electro-Mechanical Systems (MEMS), optical and biological sensing applications.