Numerical study on thermal performance of TiO2, Fe3O4 and NiCr/engine oil in an inclined wavy pip

The essential intention of the existing article is to illustrate the effect of wall properties on flow and thermal behavior, through a sinusoidal inclined wavy pipe. To succeed this phenomena we assume a sinusoidal pipe consist of wavy surface, whose walls traveling down to its borders and located at an inclined position, moreover titanium dioxide (TiO₂), ferrosoferric oxide (Fe₃O₄) and nichrome (80% Ni and 20% Cr) are considered as nano-particles and unused engine oil is assumed as a base fluid. The arising mathematical equations for thermal and flow ratio with wall slip impact are solved by mathematica. Also, evaluate graphically the thermal and flow behavior of nanofluids for multi values of solid volume fractions (η), rigidity parameter (M₁), stiffness parameter (M₂), viscous damping parameter (M₃), Grashof number (G_r), slip parameter (β) and heat generation parameter (H) also discuss the streamlines for different values of solid volume fraction.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Can a Procedure for the Growth of Single-layer Graphene on Copper be used in Different Chemical Vapor Deposition Reactors?

In the last decade, catalytic chemical vapor deposition (CVD) has been intensively explored for the growth of single-layer graphene (SLG). Despite the scattering of guidelines and procedures, variables such as the surface texture/chemistry of catalyst metal foils, carbon feedstock, and growth process parameters have been well-scrutinized. Still, questions remain on how best to standardize the growth procedure. The possible correlation of procedures between different CVD setups is an example. Here, two thermal CVD reactors were explored to grow graphene on Cu foil. The design of these setups was entirely distinct, one being a “showerhead” cold-wall type, whereas the other represented the popular “tubular” hot-wall type. Upon standardizing the Cu foil surface, it was possible to develop a procedure for cm²-scale SLG growth that differed only by the carrier gas flow rate used in the two reactors.     

Morphologically controlled synthesis of 1-dimensional selenium dioxide and study of its application as catalyst for diesel fuel additive

In this research work, selenium dioxide (SeO₂) nanorods have been prepared by a solvothermal method in which a strong reducing agent (NaBH₄) was used to reduce precursor salt into SeO₂ nanorods. X-ray diffraction (XRD) technique was applied to observe the crystal structure which confirmed its tetragonal geometry. Moreover, morphology and particle size were studied by scanning electron microscopy (SEM). SEM fully described the 1-dimensional morphology of SeO₂ nanorods which then arranged themselves to create a 3-dimensional flower-like structure with an average particle size of 50 nm. Also, the catalytic activity of SeO₂ nanorods as diesel-additive was studied by defining different parameters such as fire and flash points, calorific value, cloud and pour points, specific gravity, and kinematic viscosity. Subsequently, SeO₂ nanorods proved to be an excellent diesel additive due to higher total heat content and lower value of kinematic viscosity which enhances the better performance of the diesel engine.     

110kv及其以下的油浸电力变压器的优化设计

变压器的优化设计是变压器设计的核心,根据变压器自身的特征,通常采用遗传算法进行优化。本系统通过采用改进GA的父代参与竞争的最优保存遗传算法进行优化,得到了几乎必然收敛的优化效果。     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

用带时序子模块的系统动力学模型预测Brent原油价格

提出在系统动力学模型中加入时序自回归AR(p)子模块，并且自动确定每个AR(p)子模块的阶数p。带时序子模块的系统动力学模型既体现了因素问的横向因果关系，又体现了每个因素的纵向关系。建立欧佩克(OPEC)石油产量、世界GDP、煤炭产量与价格、天然气、需求量、供求差额、消费系数、非欧佩克石油产量、非欧佩克供求差额，石油库存和OPEC组织的期望油价共十一个因素影响下的Brent原油价格预测模型，模型的预测结果表明：在系统动力学模型中加入时序自回归AR(p)子模块的方法是可行的、有效的，并且能提高模型的预测精度。     

重油催化装置反应系统的技术改造

为了减少炼油厂高低并列式两段再生重油催化裂化装置频繁停工 ,降低干气产率 ,提高加工能力和掺渣能力 ,兰州石化公司炼油厂对该装置进行了技术改造 ,同时多产了液态烃和柴油 .新鲜原料和回炼油改由 BWJ型高效雾化进料喷嘴注入 ,沉降器由原来的三叶快分换为全封闭直联快速分离系统 ,在原来采用急冷油作终止剂的基础上 ,新增急冷水 .通过改造 ,有效地降低了干气产率 ,减少了结焦 ,增加了轻质油收率 ,提高了装置的加工能力、掺渣能力及柴汽比 ,较好地实现了预期目标     

志丹活性白土对食用油的脱色研究

以志丹白土为原料，经酸活化所得活性白土应用于食用油的脱色，详细研究了脱色工艺条件，并与浙江等地的活性白土产品的脱色效果进行比较，结果表明：志舟活化白土具有较好的脱色性能。     

GaN氢化物气相外延生长系统的设计与制作

根据GaN氢化物气相外延生长(HVPE)的原理,设计制作了双温区卧式HVPE系统．根据实际生长中出现的问题和CaN样品的测试情况,对系统进行了逐步的调试和改进．