Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

高温作用后砂岩物理力学性质阈值温度的确定——基于机器学习算法

通过采用机器学习算法，提出了高温作用后砂岩物理力学性质变化的阈值温度的确定方法。基于Python语言，利用K-Means、SVM算法，实现了对样本数据的分类和聚类，确定了阈值温度区间，验证了二分类法的合理性和准确性.结果表明，砂岩样本的阈值温度区间为400~600 ℃，阈值温度上下砂岩的物理力学性质存在显著差异，体现为阈值温度区间以下的岩样物理力学性质较为分散，而阈值温度区间以上的岩样物理力学性质较为集中.     

感应熔敷WC/Ni基复合涂层的组织和性能

采用高频感应熔敷技术，以Ni60A自熔合金粉末、微纳米碳化钨粉末为原料，在16Mn钢表面制备出以微纳米WC颗粒为增强相的Ni基金属陶瓷涂层，并测试了涂层的显微硬度。利用磨擦磨损试验机，以45#钢为对磨偶件，评价了涂层的滑动干磨擦性能。实验结果表明：涂层的硬度为890～910,磨擦系数为0．3-0．4，耐磨性比16Mn钢提高4倍以上。     

电磁场中带电粒子束运动的力学模拟

研究以不同初速度进入互相垂直的匀强磁场和均强电场中的带电粒子束的运动情形，并同相似的力学运动相比拟，建立了直观的力学模型。     

医用降温仪的设计与试验研究

介绍应用机械制冷方法设计医用降温仪的过程，并对所研制的降温仪进行试验和分析研究。     

93W合金有关力学参量的综合选评

 对93W合金材料进行了超声测量实验，并结合原有的超声测量结果进行了分析比较，提出了可以直接用冲击波速度关系式的三个系数c₀ 、λ和λ′来对钨合金的有关力学参量，如G₀、K₀、G₀′、K₀′等进行综合选评的方法。得到了一组对93W合金较为合理的力学参量推荐值。     

钢纤维混凝土桥面铺装试验研究与工程应用

针对桥面铺装层的受力状况和破坏原因 ,重点对钢纤维砼材料进行了抗弯强度试验和耐磨损试验 ,并进行了钢纤维砼弯曲性能分析 ,闸述了钢纤维砼的耐磨机理 ;结合 130 76m2 的实际工程应用 ,进行了钢纤维砼桥面铺装施工技术总结 ,分析了采用钢纤维砼作为桥面铺装层所带来的效益 ,可供类似工程参考应用     

复合体系方法测量液体力学谱

本文介绍了采用复合体系，测量得到凝聚态物质从固态到液态连续变化力学谱的一种新的实验方法。以簧振动为例，给出了解析的计算公式，以及应用条件。通过进一步综合分析，得到具有更广应用范围的近似公式，可以近似应用于其他不同的振动模式，如低频扭摆。应用新的测量方法，给出了典型小分子玻璃材料甘油和碳酸丙稀从玻璃态到液态的力学谱，观察到甘油和碳酸丙稀玻璃化转变、碳酸丙稀的再结晶、熔化和挥发的过程；测量得到挥发过程中水的质量随时间精确变化的曲线。最后，本文给出了新方法的一些应用展望。     

Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.