铁路曲线状态下横向力的研究

阐述了横向力计算的必要性,介绍了铁路曲线状态下横向力的计算方法,通过计算得出了横向力与车重、超高、速度、曲线半径的关系, 并提出了减小横向力的主要措施.     

利用振幅调制器进行光电负反馈抑制激光强度噪声

采用振幅调制器作为抑制激光强度噪声的元件，首先对光电负反馈回路进行了简要的理论分析，然后利用该光电负反馈进行抑制激光二极管抽运全固化单频环形Nd:YVO4红外激光器强度噪声的实验。结果表明，在0－1MHz的低频段，强度噪声大幅度降低，最大降低约15dB。     

用能量法求多自由度振动系统的角频率

利用简谐振动能量方程，通过分析振幅矢量的关系，用能量法求多自由度振动系统的角频率或简正振动频率。     

Naphthyl azomesogens with lateral chloro groups

A homologous series of azomesogens, 2″-[4-(4′-n-alkoxybenzoyloxy)-2-chlorophenylazo] naphthalenes, with lateral chloro groups was synthesised. All the homologues synthesized exhibit enantiotropic nematic mesophase. The mesomorphic properties of the present series are compared with other structurally related series to evaluate the effect of lateral chloro group and its position on mesomorphism This paper was presented at the 10th National Conference on Liquid Crystals held at Bangalore, India during 9–11 October 2003.     

水平均匀大气中多束光在接收面上的相关性及其对光强起伏的影响

在科尔莫戈罗夫理论的基础上，推广了光束在接收面上相关函数的物理含义。分析了多光束在接收面上的相关性。并在此基础上形成多光束光强起伏方差的解析表达式。分析结果表明，随着信道间距的增加，信道相关性下降。到达接收面的光强起伏方差降低；当信道完全重合，即相关系数变为1时，叠加后的光强起伏方差没有明显降低。与单光束时没有区别；在允许范围内增加光束数目可降低光强起伏。     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Measurements of Time-Varying Characteristics of Optical Signals and Inhomogeneities of Tested Substances with Additional Phase Modulation

The problem of investigation of the amplitude and phase structure of a time-varying probing optical signal and the structure of time-varying inhomogeneities of a substance tested by this signal is considered. The analysis is concerned, in particular, with determination of the structure of signals and processes with resolution in the pico- and femtosecond range. The scheme used for the analysis is based on registration of four spatially separated spectra of the studied radiation. The spectra are formed in a four-channel scheme with a twin-wave Michelson interferometer and a spectral device. Modulators based on electrooptical crystals (perovskites) are placed in the channels. The sum spectra are formed: without modulators, with the effect of either of the modulators, and with both of them affecting the radiation. The effect of the studied substance implies either modulating the radiation (in this case it is described by multiplication) or redistributing the radiation (then it is described by convolution).     

Measurements of Optical Signals and Their Spectra in the Femtosecond Range with Additional Phase Modulation

A solution to the phase problem in optics is considered within the context of the analysis of signals changing in time and of the effect of an object under investigation on the probing radiation. The solution is based on the use of a twin-wave interferometer with phase modulation in one of the channels and a spectrometer. The analysis is concerned, in particular, with signals and processes of ultrashort duration. To shift the frequency in the interferometer channel, an electrooptical crystal of ferroelectric perovskite is used as the modulator. Errors of amplitude and phase structures determined are analyzed.     

提高微波功率源性能的一种新型控制系统

本控制系统用于抑制大功率速调管输出微波功率宏脉冲平顶波纹,改善电子直线加速器输出束流的品质.控制方法采用微分线性逼近和矩阵算法对系统的输入和输出进行分析,求出代表系统响应的传输矩阵,从而将复杂的激励一响应计算转化为简单的代数运算.实验结果显示出宏脉冲平项波纹得到了有效抑制,说明采用自适应前馈控制来获得平坦的宏脉冲平顶是切实可行的.     

Analysis method of the effect of fabrication errors on a planar waveguide demultiplexer

The impact of fabrication errors on a planar waveguide demultiplexer is analyzed based on an analytical method. The explicit expression of the transfer function taking into account phase and amplitude errors is presented in order to analyze the loss and crosstalk of the demultiplexer caused by fabrication errors. A basic requirement for the demultiplexer with a certain crosstalk criterion can be easily obtained. Using an etched diffraction grating demultiplexer as an example, it is shown that the analytical results have a good agreement with results from a numerical method.