超高功率超短脉冲发展的现状及相关科学问题

超高功率超短脉冲激光系统在其聚焦焦点附近可以实现高达1022-24 W/cm2的峰值功率输出,为强场物理实验研究,以及实验室内模拟极端环境下的天体物理条件提供了直接的实现方案.自从国际上首次提出了建造EW激光的概念,即输出总功率达到1018 W的大型激光系统后,国际上很多国家都在设计和建造大规模的超高功率超短脉冲激光系统.本文简要介绍了国际上这种规模激光系统的发展状况,并结合国内超高功率高能超短脉冲激光的发展,对超高功率超短脉冲激光系统发展中相关技术问题进行阐述.     

Yield enhancement of elliptical high harmonics driven by bicircular laser pulses

We theoretically investigate the yield enhancement of elliptical high harmonics in the interaction of molecules with bicircular laser pulses by solving the time-dependent Schrödinger equation. It is shown that by adjusting the relative intensity ratio of the two bicircular field components in specific ranges the yield of the molecular high harmonics for the plateau and cutoff regions can be respectively enhanced. To analyze this enhancement phenomenon, we calculate the weights of the electron classical trajectories. Additionally, we also study the ellipticity distribution of harmonics for different intensity ratios. We find that these enhanced harmonics are elliptically polarized, which we mainly attribute to the recombination dipole moment of the major weighted trajectories. These enhanced elliptical extreme ultraviolet and soft x-ray radiations may serve as essential tools for exploring the ultrafast dynamics in magnetic materials and chiral media.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

感应熔敷WC/Ni基复合涂层的组织和性能

采用高频感应熔敷技术，以Ni60A自熔合金粉末、微纳米碳化钨粉末为原料，在16Mn钢表面制备出以微纳米WC颗粒为增强相的Ni基金属陶瓷涂层，并测试了涂层的显微硬度。利用磨擦磨损试验机，以45#钢为对磨偶件，评价了涂层的滑动干磨擦性能。实验结果表明：涂层的硬度为890～910,磨擦系数为0．3-0．4，耐磨性比16Mn钢提高4倍以上。     

Analysis on X-Ray Laser Generation with EM-Wave Wiggler

The possibility of realizing SASE Free Election Laser in x-ray waveband with EM-wave wiggler is studied in this paper. SASE effect including saturation length, saturation power and nonlinear process is explored through a 3-D simulation code. A utilization of seed light from laser plasma x-ray is also analyzed, which demonstrates the feature of shortening the interaction length for saturation. The results show that sizeable output power of x-ray laser would be generated with a middle energy electron beam.     

Micromachining of circular ring microstructure by femtosecond laser pulses

In this paper, integration of interference phenomenon into femtosecond laser micromachining was reported as the femtosecond laser pulses were reshaped spatially to perform ablation. The generation of circular interference pattern was demonstrated by overlapping infrared femtosecond laser pulses. The interference pattern was subsequently focused on a copper substrate to ablate microstructures of concentric circular rings. The present technique is expected to open up new applications in the areas of rapid fabrication of micro-Fresnel lenses, hybrid microlenses and lens arrays.     

双掺(Tm3+,Tb3+)LiYF4激光器1.5 μm波长激光阈值分析

由速率方程推出了双掺（Tm^3 ,Tb^3 ）离子准四能级系统的激光阈值解析式，讨论了Tm^3 和Tb^3 离子之间的相互作用。分析了1.5μm波长附近的激光阈值和Tm^3 、Tb^3 离子的掺杂原子数分数及晶体长度的关系。结果表明，对于对应Tm^3 离子^3H4→^3F4跃迁的约1.5μm波长的激光，激活离子Tm^3 的掺杂原子数分数过大时，交叉弛豫作用将使系统阈值迅速增加。Tb^3 离子的加入，一方面能抽空激光下能级，起到降低阈值的作用；另一方面亦减少了激光上能级的寿命，使阈值升高。故Tb^3 离子有最佳掺杂原子数分数。对于Tm原子数分数为y=0.01的Tm:LiYF4晶体，Tb^3 离子的最佳掺杂原子数分数为0.002左右，同时表明，激光阈值与晶体长度有关。最佳晶体长度与Tm^3 、Tb^3 离子的掺杂原子数分数以及晶体的衍射损耗和吸收损耗有关。     

环状连续强激光下光学薄膜的瞬温和热畸变

详细研究了非冷却光学薄膜元件在环形激光光束辐照下的瞬态温度分布和随后的热畸变，并且用泰曼干涉仪实际测量了连续波氧碘激光辐照各种非冷却光学元件的热畸变量并与理论计算相比较，分析结果表明理论和实验相一致。     

检测陀螺仪转子安装精度的一种新方法

陀螺仪转子的安装精度对其运行的稳定性和精确性有很大的影响。由于要求的安装误差很好，因此，对其误差的测量要求准则。其测量误差应经安装误差小1／10以及上，一般的检测方法很难达到要求，为此介绍了一种新型的光电检测方法，该方法利用狭缝的光学傅立叶变换提取陀螺仪转子的误差信息，采用计算机进行信息处理，从而完成陀螺仪转子的自动检测和分类，该方法也可用于其他一些精密年的自动检测处理。