Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

用毛细管测量纯水表面张力系数的误差讨论

通过用毛细管测量纯水表面张力系数实验，得到管内径d与接触角θ的相对误差之间的关系曲线，由此说明实验测得的表面张力系数α和理论公式相比呈现一定的偏差，并简单地讨论了实验的理想状态与实际情况的差别．     

Cold compaction of ceramic powder: Computational analysis of the effect of pressing method and die shape

This paper deals with a computational analysis of the influence of the pressing method and part geometry on the final density distribution in the cold compaction process of ceramic alumina powders. The analysis is based on the explicit finite-element model proposed and validated in a previous study. The mechanical behavior of the processing material is described using a multisurface elastoplastic model, the modified Drucker-Prager/Cap model Published in Prikladnaya Mekhanika, Vol. 43, No. 10, pp. 129–134, October 2007.     

玻璃器皿压机转位机构凸轮——槽轮机构的研究

论述了一种拨销回转半径可变的凸轮——槽轮机构。叙述了玻璃器皿压机转位机构的运动要求。研究了用这种机构驱动工作台间歇转动的设计方法。     

内源全息术的原理和数学描述

以往的全息术在对原子成像时,在相干光源、探测器空间分辨和信号强度三个方面遇到了难以克服的困难. 阐述了内源全息术克服这些困难的原理,研究了内源全息术的记录和再现全过程,推导出内源球面全息图的再现公式,并在散射因子球对称近似和能量无关近似下,推导出以δ函数表示原子全息再现像的解析表达式. 关键词： 内源全息术 同步辐射 晶体结构 傅里叶变换     

全剪结构阴角细部施工技术总结

针对混凝土阴角质量问题,提出了改进和加强全现浇剪力墙结构各种阴角细部质量的措施,从而保证了混凝土阴角质量达到普通抹灰质量标准。     

X-射线荧光光谱法测定钛铁中的硅、锰、磷、铝

介绍用X-射线荧光光谱仪测定钛铁中Si、Mn、P、Al含量的方法,通过试验确定了合适的研磨时间、压力和保压时间,用压片法制样,建立了各元素的工作曲线,各元素的测定范围分别为Si3.00%～6.00%,Mn1.00%～3.00%,P0.030%～0.070%,Al5.00%～9.00%。通过强度测量得到测定Si、Mn、P、Al的相对标准偏差分别为0.074%、0.308%、0.383%、0.040%,精密度满足测试要求。将该方法测定结果与化学法比对,准确度满足国家标准方法分析误差的要求。     

回流充气法处理中,高量含铁地下水的研究

本文介绍一种深井回流充气工艺,它兼具充氧和除铁综合性能的新型工艺形式,能改善含铁地下水的过滤性能.在此基础上提出了深井回流充气稳定期的概念,建立了深井回流充气系统中氧量的平衡关系.通过正交试验,提出了处理中、高量含铁地下水的推荐工艺流程和工艺参数.采用χ—射线衍射方法测试了井内铁泥和成熟滤料表面滤膜的成分和形态,分析了"充气"和"过滤》两过程中的除铁机理.     

Bi系高温超导带材冷压工艺优化试验

采用套管法（ＰＥＴ）制备Ｂｉ系高温超导带材,进行了冷压工艺的优化研究。试验结果表明,Ｂｉ系带材所能承受的压力有一个限值,若超过这个限值后,密度虽可提高,但晶粒破碎严重Ｊｃ值反而降低,带材优化的冷压工艺参数是８３８℃／６０ｈ＋冷压＋８３８℃／６０ｈ。第１次压力为２ＧＰａ,第２次２．５ＧＰａ;冷压压下速率为１．５×１０＾－４ｍｍ／ｓ。同时研究还表明冷压的主要作用是提高带材的致密度和晶粒取向度,最终改善