CO2跨临界循环系统润滑油分析

为保证CO2跨临界循环系统的稳定运行，选择与之相适应的润滑油，在分析摩擦润滑特性的基础上，采用实验数据对比的方法，对POE、PAG、PAO和烷基芳香烃4类合成润滑油在CO2跨临界循环系统中的混合性、流动性、可溶性、黏度、长期稳定性及润滑性等性能进行了分析，结果表明POE类润滑油是CO2跨临界循环系统的一种相对较好的选择。     

复合体系方法测量液体力学谱

本文介绍了采用复合体系，测量得到凝聚态物质从固态到液态连续变化力学谱的一种新的实验方法。以簧振动为例，给出了解析的计算公式，以及应用条件。通过进一步综合分析，得到具有更广应用范围的近似公式，可以近似应用于其他不同的振动模式，如低频扭摆。应用新的测量方法，给出了典型小分子玻璃材料甘油和碳酸丙稀从玻璃态到液态的力学谱，观察到甘油和碳酸丙稀玻璃化转变、碳酸丙稀的再结晶、熔化和挥发的过程；测量得到挥发过程中水的质量随时间精确变化的曲线。最后，本文给出了新方法的一些应用展望。     

Nano-tribological study on a super-hydrophobic film formed on rough aluminium substrates

A novel super-hydrophobic stearic acid (STA) film with a water contact angle of 166^o was prepared by chemical adsorption on aluminum wafer coated with polyethyleneimine (PEI) film. The micro-tribological behavior of the super-hydrophobic STA monolayer was compared with that of the polished and PEI-coated Al surfaces. The effect of relative humidity on the adhesion and friction was investigated as well. It was found that the STA monolayer showed decreased friction, while the adhesive force was greatly decreased by increasing the surface roughness of the Al wafer to reduce the contact area between the atomic force microscope (AFM) tip and the sample surface to be tested. Thus the friction and adhesion of the Al wafer was effectively decreased by generating the STA monolayer, which indicated that it could be feasible and rational to prepare a surface with good adhesion resistance and lubricity by properly controlling the surface morphology and the chemical composition. Both the adhesion and friction decreased as the relative humidity was lowered from 65% to 10%, though the decrease extent became insignificant for the STA monolayer. The project supported by the National Natural Science Foundation of China (50375151, 50323007, 10225209) and the Chinese Academy of Sciences (KJCX-SW-L2)     

路径对摩擦力做功的影响

本文通过讨论两种临界情况下摩擦力所做的功的变化情况，进一步阐明非保守力做的功与路径有关．     

Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

快冷Fe_(71)Al_(29)合金中的两个内耗峰

用一个计算机控制的倒扭摆研究了快冷Fe71 Al2 9合金中的两个内耗峰 .在快冷的Fe71 Al2 9样品中分别在 180℃(P1 ) ,340℃ (P2 )和 5 10℃ (P3)出现了内耗峰 ,而在慢冷的Fe71 Al2 9样品中只发现了P3峰 .快冷样品中的P1 和P2峰在从 6 5 0℃冷却下来的测量过程中或在 35 0℃经过较长时间的时效后消失 ,其峰高随时效时间的增加而下降 ,直至消失 .P1 和P2 峰都有弛豫特征 ,它们的激活能分别为 :H1 =1.0 3± 0 .0 8eV(P1 峰 ) ;H2 =1.6 4± 0 .0 5eV(P2 峰 ) .P1 峰被认为是无序合金中Al原子在四面体点阵内的最近邻运动所引起 ,P2 峰则是无序合金中Al原子在四面体点阵内的次近邻运动所引起     

Sufficient conditions of non‐uniqueness for the Coulomb friction problem

We consider the Signorini problem with Coulomb friction in elasticity. Sufficient conditions of non‐uniqueness are obtained for the continuous model. These conditions are linked to the existence of real eigenvalues of an operator in a Hilbert space. We prove that, under appropriate conditions, real eigenvalues exist for a non‐local Coulomb friction model. Finite element approximation of the eigenvalue problem is considered and numerical experiments are performed. Copyright © 2003 John Wiley & Sons, Ltd.     

对摩擦力作功与摩擦生热的量度的认识

本文通过对摩擦力作功与不擦生热的讨论，给出摩擦生热的量度方法．     

筒型基础系缆平台沉／拔过程侧摩阻力原型测试

介绍了1999年首次安装在渤海锦州9－3地区多筒基础平台安装施工过程中的侧摩阻力原型测试研究，描述了简型基础上沉和上拔过程中筒壁侧摩阻力的测试系统和测试方法，给出了主要测试结果并与现行规范进行了对比分析，这项成果对筒型基础平台的设计和施工具有直接的参考意义。     

Φ12LMQ型钢筋冷拉机原理及主要参数选择

介绍了一种新型钢筋冷拉机的工作原理和主要参数：变形速度Ｖ△Ｌ、单位时间伸长率ε、送进速度Ｖ２、冷拉速度Ｖ１及其之间的关系．这种冷拉机具有生产率高、冷拉质量稳定等特点．