螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

A unified theory for brittle and ductile shear mode fracture

A unified theory captures both brittle and ductile fracture. The fracture toughness is proportional to the applied stress squared and the length of the crack. For purely brittle solids, this criterion is equivalent to Griffith's theory. In other cases, it provides a theoretical basis for the Irwin-Orowan formula. For purely ductile solids, the theory makes direct contact with the Bilby-Cottrell-Swinden model. The toughness is highest in ductile materials because the shielding dislocations in the plastic zone provide additional resistance to crack growth. This resistance is the force opposing dislocation motion, and the Peach-Koehler force overcomes it. A dislocation-free zone separates the plastic zone from and the tip of the crack. The dislocation-free zone is finite because molecular forces responsible for the cohesion of the surfaces near the crack tip are not negligible. At the point of crack growth, the length of the dislocation-free zone is constant and the shielding dislocations advance in concert. As in Griffith's theory, the crack is in unstable equilibrium. The theory shows that a dimensionless variable controls the elastoplastic behaviour. A relationship for the size of the dislocation-free zone is derived in terms of the macroscopic and microscopic parameters that govern the fracture.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

ZnO nanowire lines and bundles: Template-deformation-guided alignment for patterned field-electron emitters

One-dimensional ZnO materials have been promising for field-emission (FE) application, but how to facially control the alignment of ZnO emitters is still a great challenge especially for patterned display application. Here, we report the fabrication of novel ZnO nanowire (NW) line and bundle arrays for patterned field-electron emitters. The effects of PS template size and heating time on the resulted ZnO nanoarrays were systematically studied. The deformation degree of PS templates was controlled and hence utilized to adjust the alignment of electrochemically deposited ZnO arrays. It was found that the length of NW lines and the density of NW bundles can effectively tuned by the PS template heating time. The optimal FE performance with turn-on electric field as low as of 4.4 V μm⁻¹ and the field-enhancement factor as high as of 1450 were achieved through decreasing the screening effect among the patterned field-electron emitters.     

基于热中子探测评价裂缝的示踪剂特性研究

针对裂缝热中子示踪探测方法,从中子双组扩散理论入手结合蒙特卡洛数值模拟方法,分析压裂前后地层热中子分布影响因素,并模拟不同类型示踪剂及含量的热中子裂缝响应规律,筛选最佳示踪剂并给出其在支撑剂中含量的上、下限。结果表明:压裂前后热中子计数变化量主要受裂缝宽度和标记支撑剂中示踪剂含量的影响;钆对裂缝宽度变化反应最灵敏,钆元素是作为标记支撑剂的最佳示踪元素;随支撑剂中Gd 2O 3含量的增加,热中子计数率降低,热中子计数变化量D增加;示踪剂中氧化钆的上、下限值随裂缝宽度呈指数降低,且当裂缝宽度为1.0 cm时,Gd 2O 3的质量分数上限为0.68%,下限为0.03%。     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

塔东热液地质作用机制及对储层的改造意义

塔东地区断裂发育，早期发育的断裂与晚期断裂之间存在相互改造、叠加、复合的过程，深大断裂沟通多套地层，断裂活动期形成的挤压破碎带和断裂裂缝带作为岩浆热液上升通道，为热液溶蚀作用改造储层提供了有利条件，因此，识别出热液期次对塔东白云岩储层成因机制具有重要意义。通过对钻井岩芯、岩屑及岩石薄片、铸体薄片观察鉴定分析，在区内下古生界碳酸盐岩中识别和发现了钠长石化作用和自生羽毛状伊利石沉淀，也是塔里木盆地内的首次发现，并通过对包裹体均一温度，碳氧同位素等地化特征研究，揭示其成岩流体源于岩浆热液，丰富了区内热液作用的矿物学标志，进一步识别出区内存在3期热液作用，通过对3期热液作用的机制及其储渗空间意义的研究，总结出第I期热液作用对于储层形成意义不大，第Ⅱ期热液作用主要发育在局限的沉积环境，第Ⅲ期热液溶蚀形成溶蚀缝孔洞，与天然气运移聚集匹配良好，构成了区内天然气聚集成藏的主要储渗空间。     

借助Matlab遗传算法反演火山区压力源参数

首先分析了Mogi模型的经典最小二乘反演由于出现矩阵奇异或接近奇异而发散的局限性,决定采用具有全局高效搜索性和优化计算时不需要求导的遗传算法来反演火山区压力源参数。反演程序调用Matlab7.0 Release14工具箱中的选择、交叉和变异等相关程序。最后应用该程序和长白山天池火山区水准和GPS观测资料联合反演火山区压力源参数,经过比较遗传算法和阻尼最小二乘方法的反演结果,可看出2种方法结果近似,可见此方法方便快捷地实现了目标函数的最小化。     

双奇核136La的集体带结构

通过重离子核反应与在束γ谱的实验技术, 对A=130缺中子核区的双奇核¹³⁶La的高自旋态进行了研究, 所用核反应为¹³⁰Te(¹¹B,5n). 实验结果扩展了¹³⁶La的能级纲图, 包括3个集体转动带, 最高自旋态达20h. 对于\uppi h_{11/2}\otimes \upnu h_{11/2}$~带, 观测到了旋称反转与集体回弯现象. 通过系统学比较, 对旋称反转特性进行了讨论. 由推转壳模型的计算指出, 此集体回弯是由一对中子的角动量顺排引起的. 另外两个集体带为具有~$\gamma\approx -60^\circ$~的扁椭形变带, 其可能的组态为: $\uppi h_{11/2}\otimes \upnu g_{7/2}h_{11/2}^2$~与~$\uppi g_{7/2}\otimes\upnu g_{7/2}^2 d_{5/2} h_{11/2}^2$.