多级孔板提高井筒气体携液能力实验研究

气井生产时，井底积液会影响气井产量，甚至导致气井停产。加入泡沫剂、更换小直径油管或氮气举升等措施排出井底积液是保证气井生产的重要手段，但造成液体回流的井筒结构并没有变化。改变适合于单相流体的均一井筒结构，降低气液两相流中液体在井筒的回流，提高气体携液能力，形成适用于气液两相流的井筒结构，可以改善气井生产。实验设计了安装于管筒内的类似于倒置漏斗形的多级孔板装置，以井底气体为动能，借助“爬楼梯”原理，利用孔板减少或阻止液体回流，使液体通过多级孔板逐级上升；实验利用气体压缩机提供气源，测试了不同气体流速下，加入孔板对于气体和泡沫携液能力的影响。实验表明，在管筒内加入液体回流限制装置，大幅度地提高了管筒的气体携液能力和排液效果，减少了管筒液体回流量，降低了气体排液和泡沫排液的气体流速临界值。多级孔板可用于气井增产，能够提高气体携液能力，提高泡沫携液效果，降低泡沫剂的使用量和井底残液，但在实际生产中气体流量和装置的匹配性，还有待于在现场试验中进一步验证和优化。     

“二三结合”开发模式渗流特征研究

L油田B区块开展"二三结合"实验区,"二三结合"开发模式渗流特征对区块的合理高效开发具有重要意义。为了明确其渗流特征,利用油藏数值模拟软件Eclipse建立代表意义的油藏数值模型,研究区块"二三结合"开发模式下原射孔层和补孔层的渗流特征,分析了"二三结合"开发模式下,不同开发阶段综合含水率、采出程度、井底压力、地层压力及含水饱和度的变化特征。研究表明,"二三结合"开发模式先通过水驱开发挖潜原射孔层剩余油,提高厚油层顶部剩余油的采出程度,再通过聚合物驱进一步提高开发效果,通过水驱与聚驱的综合作用,最终得到较好的开发效果。     

Polarized Spacetime Foam

An approximate model of a spacetime foam is presented. It is supposed that in the spacetime foam each quantum handle is like to an electric dipole and therefore the spacetime foam is similar to a dielectric. If we neglect of linear sizes of the quantum handle then it can be described with an operator containing a Grassman number and either a scalar or a spinor field. For both fields the Lagrangian is presented. For the scalar field it is the dilaton gravity + electrodynamics and the dilaton field is a dielectric permeability. The spherically symmetric solution in this case give us the screening of a bare electric charge surrounded by a polarized spacetime foam and the energy of the electric field becomes finite one. In the case of the spinor field the spherically symmetric solution give us a ball of the polarized spacetime foam filled with the confined electric field. It is shown that the full energy of the electric field in the ball can be very big.     

The Modeling of Velocity Enhancement in Polymer Flooding

In single-phase polymer flooding experiments it has repeatedly been observed that the average velocity of the polymer molecules is higher than the average velocity of the water molecules. This effect is incorporated in many conventional Enhanced Oil Recovery (EOR) simulators by the introduction of a constant velocity enhancement factor. In this paper we show that, in absence of dispersion, a constant enhancement factor in the mathematical model for two-phase polymer flow (Buckley--Leverett displacement) leads to ill-posedness of the model equations. We propose a saturation dependent enhancement factor, derived from a model based on percolation concepts, for which this problem does not occur.     

液态泡沫结构及其稳定性

液态泡沫由大量气泡密集堆积在少量的表面活性剂溶液中形成，是具有高度自组织结构的典型的软物质．文章从泡沫物理学角度简要介绍了液态泡沫的结构特征和稳定性方面的研究．     

泡沫的持液量研究

泡沫的持液量（ｈ，ｍｇ／ｃｍ３）是泡沫的基本特性之一．本文对形成泡沫的起泡剂浓度、增粘剂浓度、气体流量和温度等因素对Ｈ的影响及变化规律作了研究，并对Ｈ与泡沫表观粘度和泡沫半衰期的相互关系作了描述，对泡沫的实际应用具有一定的指导意义．     

泡沫铅对VRLA电池负极活性物质结构及性能影响

0引言随着36V/42V汽车电源系统的提出,新一轮汽车用电池的竞争不断加剧。从目前情况看,铅酸电池由于具有成本低廉,使用可靠,原材料来源丰富,铅回收率可高达98%等优点,因此成为电动车电源最实际的选择之一[1]。但作为电动车用电池,需要克服其比能量低、充电接受能力差和负极硫酸盐化等缺点。为此各国科学家开展了大量的研究工作。最近报道用铸造多孔体作为敞口铅酸电池的集流体,它的比表面积为14cm2·cm-3,正极活性物质利用率上升到50%,远高于传统的铸造板栅[2]。在铅酸电池集流体研究领域里另一个重大进步,就是以R V C(R etic-ulated V i…     

Dynamic Interfacial Tension Behavior of Water/Oil Systems Containing In situ-Formed Surfactants

Time-dependent interfacial tension (IFT) has been investigated for an interfacially reactive immiscible system composed of model-acidified oil and alkaline water. The acidified oil was composed of either lauric acid or linoleic acid dissolved in n-dodecane. Drop volume tensiometry was employed to measure the interfacial tension between the two phases. In the case of lauric acid, the IFT value was found to decrease sharply with increasing alkali concentration, even at low drop formation times. In the case of linoleic acid, the IFT decrease with the drop formation time was more gradual, especially at low alkali concentration. The rate of formation of the interfacial area was also found to be dependent on alkali concentration.     

表面膨胀粘度的测定研究

用不同浓度的NaCl和表面活性剂直链的十二烷基苯磺酸钠(LAS)、稳定剂聚丙烯酰胺和水所组成的泡沫体系为研究对象,通过表面压松弛的方法,利用计算机数据拟合,得到了计算表面膨胀粘度的方法。     

Preconcentration and separation of iron, zinc, cadmium and mercury, from waste water using Nile blue a grafted polyurethane foam

The present work describes a novel method for the incorporation of Nile blue A into polyurethane foam matrix. This foam material was found to be very suitable for the extraction of metal ions from aqueous solutions. The characterization of Nile blue A grafted foam and the effect of halide concentration, pH, shaking time, extraction isotherm and capacity have been investigated. This foam material was found to be suitable for the separation and preconcentration of iron (III), zinc (II), cadmium (II) and mercury (II) from waste water. The extraction was accomplished in (15-20) minutes. Iron was separated from acid medium (2-4 M HCl), zinc from (3-5 M HCl), cadmium from (4-6 M HCl) as thiocyanate complexes and mercury was separated from (1-2 M HCl) as chloride.