医药洁净室的计算流体动力学模拟及实测对比

采用计算流体动力学(CFD)模拟,研究3个医药洁净室的气流流型及颗粒物浓度.采用标准k-ε双方程模型,通过模拟颗粒物在洁净室的分布,分析合理的污染物散发位置及散发比例.对比参考发尘量下的结果与实测数据的差异,根据实测数据确定污染散发量,通过试验不同的单位容积发尘量,计算对应的洁净度,得到与实测数据吻合最好的单位容积发尘量.在单位容积发尘量为1 000pc·(m3·min)-1计算条件下,各房间的模拟结果与实测数据数值比较吻合,且经CFD预测的3个房间的洁净度变化趋势与实测一致.     

Highly Luminescent Red Phosphorescent OLED with Interfacial Layers for Hole Transport and Electron Injection

Four kinds of red phosphorescent organic light-emitting devices were fabricated and compared to investigate the effect of interfacial layers for hole transport and electron injection. 1 nm-thick LiF in the device A and C and 1 nm-thick Cs₂CO₃ in the device B and D were deposited as an electron injection layer between the anode and the electron transport layer, and 5 nm-thick layer of dipyrazion[2,3-f:2′,2′-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile[HATCN] was inserted as a hole transport interfacial layer between the hole injection layer and the hole transport layer only in the device C and D. Under a luminance of 1000 cd/m², the power efficiencies were 7.6 lm/W and 8.5 lm/W in the device A and B, and 8.6 lm/W and 13.4 lm/W in the device C and D. The quantum efficiency of the device D was 15.8% under 1000 cd/m² which was somewhat lower than those of the device A and C, but a little higher than that of the device B. The luminance of the device D was much higher than those of the other devices at a given votage. The luminance of the device D at 7 V was 23,710 cd/m², which was 13.0, 3.4, and 4.0 times higher than those of the device A, B, and C at the same voltage, respectively.     

高静态动作压力下粉尘爆炸泄放标准的可靠性

粉尘爆炸泄放设计标准的可靠性对能否实现爆炸防护尤为关键.以中径70μm石松子粉尘为介质,采用20 L球形粉尘爆炸装置进行了4种泄放口径、静态动作压力在0.12~0.6 MPa的爆炸泄放实验,对比了实验值与NFPA 68和EN 14491计算值.结果表明,NFPA 68在预测高静态动作压力下的泄放面积时,随着泄放口径的增大,预测结果由保守变为危险,但预测结果精度较好且数值稳定;EN 14491在预测高静态动作压力下的泄放面积时非常保守,预测精度较差,数据不可靠.依据两种标准推荐的经验函数关系,分析了NFPA 68和EN 14491在预测高静态动作压力时产生这种差异的原因.     

Controlled synthesis of ZnO nanoparticles from a Zn(II) coordination polymer: Structural characterization,optical properties and photocatalytic activity

A zinc coordination polymer derived from pyridine-2,6-dicarboxylate (PDC), {[Zn₂(PDC)₂]}_n, was successfully prepared via conventional, sonication and microwave-irradiation methods. The composition and characteristics of the obtained coordination polymers (CPs) were investigated by elemental analysis, TGA/DTA, X-ray diffraction and spectroscopic techniques. The so obtained CPs were heat-treated in the air at 600 °C for 2 h to produce ZnO of nanosized particles (NPs). It is of interest to note that the synthesis approach of the precursor greatly affects both the nanoparticle size and the structure of the resulting ZnO NPs. Moreover, the smallest particle size was associated with the sample derived from the ultrasonically prepared precursor. TEM analysis revealed that all samples have sphere-like morphologies. Structural analysis of the prepared ZnO samples was conducted and compared using Rietveld analysis of their PXRD patterns. Optical band gap calculations based on analysis of the UV–vis spectra of ZnO samples using Tauc's power law were achieved. The highest band gap of 3.63 eV was observed for ZnO sample obtained from the ultrasonically prepared precursor. Furthermore, the photocatalytic activity of ZnO NPs for the removal of Eosin Y color was monitored. The highest removal efficiency was recorded for ZnO originated from the ultrasonically synthesized precursor. Enhancement of removal efficiency that reached 98% was attained in only a period of 8 min. Its recycling test showed that it can be reused without structural changes over four cycling experiments.     

泵站运行效率分析与节能措施

从泵站的电耗入手，讨论和分析了泵站机组实际运行工况与设计工况的偏离．并通过机组电耗和效率分析，提出了若干节能措施。     

提高风险投资过程中两级委托—代理效率的思考

本文从对风险投资者与风险投资商、风险投资商与风险企业之间的两层委托代理的简要分析入手 ,首先在诠释委托—代理效率内涵的基础上构建了分析委托—代理效率的一个理论框架 ,并应用此框架对如何提高上述两层委托—代理关系的效率问题进行了探讨     

科技论文中“关键词”的标引方法

从关键词在文献检索中的重要作用论述了科技论文的发表，必须重视关键词的标引．明确指出出版专业中关键词的概念，探讨了不同标引方法的利弊，介绍了关键词的标引方法．     

HIRFL–CSR加速器中束流与真空中剩余气体的碰撞损失

研究了重离子加速器中束流与真空中剩余气体的碰撞损失过程和碰撞截面,在依据大量实验数据的基础上,提出了一组计算离子一原子的电荷交换截面的经验公式.以兰州重离子加速器HDRFL及冷却储存环CSR为例,给出了依据碰撞截面的公式计算束流在加速器真空中的传输效率的方法,并计算了在不同真空度下HIRFL的ECR源轴向注入束运线、注入器SFC、前束运线、主加速器SSC和后束运线等不同加速阶段及CSR的传输效率,并提出合理的真空度要求.HIRFL的真空分布测量和束流的损失测量证明了该计算方法的可靠性.     

半导体激光器光束准直系统的功率耦合效率

在长距离无线光通信中，接收点光功率密度与光束发散角平方呈反比关系，为了获得小的发散角和大的功率耦合效率，要求准直系统有较大的数值孔径(NA)，但数值孔径过大会增加像差，因此合理设计功率耦合效率与准直系统的数值孔径就非常重要。该文对半导体激光器光束准直系统中功率耦合效率进行了研究，给出了半导体激光器光束功率耦合效率与k(孔径半径与孔径处等效光束半径之比)的关系表达式，并结合激光器光束准直系统，给出了半导体激光器光束功率耦合效率与准直系统数值孔径的关系表达式。该研究结论对于半导体激光器光束准直系统设计具有参考作用。     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.