Skyrmion transport driven by pure voltage generated strain gradient

The magnetic skyrmion transport driven by pure voltage-induced strain gradient is proposed and studied via micromagnetic simulation. Through combining the skyrmion with multiferroic heterojunction, a voltage-induced uniaxial strain gradient is adjusted to move skyrmions. In the system, a pair of short-circuited trapezoidal top electrodes can generate the symmetric strain. Due to the symmetry of strain, the magnetic skyrmion can be driven with a linear motion in the middle of the nanostrip without deviation. We calculate the strain distribution generated by the trapezoidal top electrodes pair, and further investigate the influence of the strain intensity as well as the strain gradient on the skyrmion velocity. Our findings provide a stable and low-energy regulation method for skyrmion transport.     

基于回转输运试验的煤散料离散元接触参数修正

为获取精确的刮板输送机离散元模拟结果，基于回转输运试验，通过响应面法对煤料的接触参数进行修正.采用Plackett-Burman试验考察接触参数对受力及堆积角的影响，发现煤-钢静摩擦系数、煤-煤摩擦系数具有显著正效应.根据爬坡试验结果，以受力及堆积角为响应值规划Box-Behnken试验，建立受力、堆积角与显著项间的二次回归多项式，以实测数据为目标值求得最佳参数:煤-钢静摩擦系数为0.401，煤-煤静摩擦系数为0.333，煤-煤滚动摩擦系数为0.041.通过不同输运条件下的回转试验验证了参数的准确性，为刮板输送机的离散元研究提供参考.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

Norbornene derivatives from a metal‐free,strain‐promoted cycloaddition reaction: New building blocks for ring‐opening metathesis polymerization reactions

The preparation of new ring opening metathesis polymerization (ROMP) monomers using a 1,3‐dipolar cycloaddition between aryl azides and norbornadiene is described. Various norbornenetriazolines, obtained through a solvent‐and catalyst‐free reaction, can subsequently be incorporated into polymer backbones through ROMP reactions. Furthermore, thermal decomposition of the triazoline moiety can allow for further polymer functionalization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2357–2362     

矩形型钢弯曲回弹曲率半径r值的确定

文章在分析矩形型钢弯曲变形过程及应力与应变等方面的关系的基础上，推导出工件曲率半径与工件回弹后曲率半径之间的关系，从而确定了凸模半径。     

A possible counterexample to well posedness of entropy solutions and to Godunov scheme convergence

A particular case of initial data for the two-dimensional Euler equations is studied numerically. The results show that the Godunov method does not always converge to the physical solution, at least not on feasible grids. Moreover, they suggest that entropy solutions (in the weak entropy inequality sense) are not well posed.

     

Comparison of growth stress measurements with modelling in thin iron oxide films

High temperature oxidation of metals leads to residual stresses both in the metal and in the growing oxide. In this work, the evolution of this residual stresses is theoretically predicted in the growing oxide layers. The origin of these stresses is based on a microstructural model. Using experimental results providing from the oxidation kinetics, and an analysis proposed to describe the growth strain occurring in the thin layers, a set of equations is established allowing determining the stresses evolution with oxidation time. Then, the model is compared with experimental results obtained on both α-Fe and phosphated α-Fe, oxidised at different temperatures. Numerical data are extracted from experiments either with an asymptotic formulation or with an inverse method. These two methods give good agreement with experiments and allow extracting the model parameters.     

注浆覆岩离层力学机理及其离层发育分类研究

依据覆岩离层生成的力学机理,结合煤层开采程度的不同,将可注浆层位的离层划分为三类.以岩石的应变为指标,确立了覆岩离层可注浆层位岩梁的断裂步距表达式,理论上证明了划分注浆层位的合理性.根据岩石的全应力应变试验,结合现场实际观测数据,对以应变为指标的岩梁断裂步距表达式做了初步验证.结果表明:可注浆层位的分类和断裂步距表达式的确定对注浆减沉工程具有指导意义.