Hyperparameter on-line learning of stochastic resonance based threshold networks

Aiming at training the feed-forward threshold neural network consisting of nondifferentiable activation functions, the approach of noise injection forms a stochastic resonance based threshold network that can be optimized by various gradient-based optimizers. The introduction of injected noise extends the noise level into the parameter space of the designed threshold network, but leads to a highly non-convex optimization landscape of the loss function. Thus, the hyperparameter on-line learning procedure with respective to network weights and noise levels becomes of challenge. It is shown that the Adam optimizer, as an adaptive variant of stochastic gradient descent, manifests its superior learning ability in training the stochastic resonance based threshold network effectively. Experimental results demonstrate the significant improvement of performance of the designed threshold network trained by the Adam optimizer for function approximation and image classification.     

复合跟踪微分器在电容式位移传感器中的应用

针对从含噪原始信号中提取位置以及速度信息,经典跟踪微分器存在不能很好兼顾相位滞后和噪声放大问题、参数多,调试复杂等不足.在跟踪微分器等效线性分析基础上,提出复合形式跟踪微分器,用于电容式位移传感器位置信号跟踪以及速度信号估计,通过MATLAB\SIMULINK仿真以及实验平台测试,结果表明:在跟踪频率1 Hz、幅值1含噪声正弦信号中,复合跟踪微分器能光滑逼近原始位置信号,且能有效进行速度估计,相较于经典跟踪微分器,复合跟踪微分器跟踪相位滞后小0.03 rad,能更好兼顾跟踪信号相位滞后及速度信号噪声放大.     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

导航系统视觉快速跟踪方法

提出了一种图象搜索的方法 ,适用于变化的环境 ,通过灰度值偏移校正二维阈值化和噪声滤波的方法能有效排除由于光源所引起的各种干扰 .本方法处理速度快 ,满足自引导车实时跟踪和导航的需要     

惯性导航系统水平阻尼网络的自适应控制

当海况变化较大时，惯性导航系统(INS)的误差振荡幅度较大．为了减小系统误差的振荡幅度，提出了一种新的设计思想，采用自适应控制方法，根据实际的海况变化情况，实时校正阻尼参数，使由舰船的机动性造成的系统误差最小．结果表明，与传统方法相比，水平误差角振荡幅度减小了约50％，速度误差振荡幅度减小了约30％．经度、纬度和航向误差振荡幅度也有明显改善；水平阻尼网络的自适应控制有效地改善了INS的动态性能．     

运用量子约束动力学对具有耗散的量子位的追踪控制

在有限温度环境内，量子约束动力学及其追踪控制可使退相干系统的相干性稳定一段时间.约束方程产生的控制场能够按量子比特的动力学状态进行控制(量子动力学轨道的反馈控制)；依靠量子比特的这种反馈效应，可使量子位稳定在设定的时间内.同时，在量子位的稳定方面，温度扮演一种消极的角色. 关键词： 量子约束动力学 耗散量子位的控制 追踪控制 量子比特的反馈效应     

用自适应脉冲微扰引导混沌系统到周期解

用自适应脉冲微扰方法控制的系统的某个系统变量作为驱动,设计了一种自适应控制器方法对两个或多个响应混沌系统进行脉冲微扰,引导这些系统从混沌运动到低周期运动,实现同时控制多个混沌系统到不同的周期态. 当选择相同的自适应控制器输入变量实施脉冲微扰时,还可控制两个或多个混沌系统达到不同的周期态同步. 通过对R?ssler混沌系统的仿真研究证实了方法的有效性. 关键词： 混沌控制 系统参量 自适应控制器 脉冲微扰 周期态同步     

Simulation of viscous water column collapse using adapting hierarchical grids

An adaptive hierarchical grid‐based method for predicting complex free surface flows is used to simulate collapse of a water column. Adapting quadtree grids are combined with a high‐resolution interface‐capturing approach and pressure‐based coupling of the Navier–Stokes equations. The Navier–Stokes flow solution scheme is verified for simulation of flow in a lid‐driven cavity at Re=1000. Two approaches to the coupling of the Navier–Stokes equations are investigated as are alternative face velocity and hanging node interpolations. Collapse of a water column as well as collapse of a water column and its subsequent interaction with an obstacle are simulated. The calculations are made on uniform and adapting quadtree grids, and the accuracy of the quadtree calculations is shown to be the same as those made on the equivalent uniform grids. Results are in excellent agreement with experimental and other numerical data. A sharp interface is maintained at the free surface. The new adapting quadtree‐based method achieves a considerable saving in the size of the computational grid and CPU time in comparison with calculations made on equivalent uniform grids. Copyright © 2005 John Wiley & Sons, Ltd.