Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.     

ICP-AES测定钛基复合材料中镍、钕和铁的研究

采用ICP－AES法对钛基复合材料中的合金元素镍、钕、铁的测定进行了研究，着重进行了基体元素及待测元素镍、钕、铁之间干扰试验及各元素在测定浓度范围内的线性相关性试验，进行了酸度试验，测定了钛基复合材料中3种元素的含量，得到了较好的精密度和准确度。方法简便、可靠，获得满意的分析结果。     

TiO2对合成渣中Fe2O3还原发泡过程的影响

研究了不同条件下TiO2和Fe2O3在合成渣中被碳还原时的发泡过程．计算了该发泡过程的发泡系数、消泡系数、平均发泡寿命、发泡强度和消泡过程开始的时间．用熔渣发泡参数定量地讨论了温度、TiO2加入量和初渣中TiC的含量对熔渣发泡过程的影响，发现当初渣中TiC的含量和TiO2加入量较多时，在发泡时会产生二次发泡现象．     

New double negative and positive temperature coefficients of conductive EPDM rubber TiC ceramic composites

In this paper, we have successfully prepared ethylene-propylene-diene monomer (EPDM)/TiC composites as thermistors, with new double negative and positive temperature coefficients of conductivity (NTCC/PTCC). EPDM composites loaded with 50 phr HAF carbon black and different concentrations of TiC were prepared. This study focuses on the effect of TiC content on the vulcanization process, the network structure and the electrical and thermal properties of EPDM/TiC composites. The effect of TiC on the network structure was evaluated e.g. the curing process, the characteristic time constant during vulcanization, the volume fraction of rubber, gel fraction, interparticle distance between conductive particles, the extent of TiC reinforcement in the rubber matrix and molecular weight between cross-linking through experimental and affine-phantom models. The effects of TiC content on the percolation theory, electrical conductivity, conducting mechanism of conductivity, conducting hysteresis and I-V characteristics were also studied, as well as its TiC on the (NTCC/PTCC), thermoelectric power, dielectric constant and thermal conductivity. Stability and reproducibility of the thermal cycles for heating element applications was tested. Specific heat and the amount of heat transfer by radiation and convection as a function of TiC content was calculated using both the calorimetric technique and a theoretical model. It was proved that TiC improves the network structure, electrical and thermal properties of EPDM composites for practical applications.     

ZTA—SiCw—TiC复相陶瓷材料强韧化机理研究

四方氧化锆相变增韧、碳化硅晶须补强、碳化钛粒子弥散强化，同时引入一个新的陶瓷基复合材料系统中产生了叠加的强韧化效果。热压ＺＴＡ－ＳｉＣｗ－ＴｉＣ复相陶瓷材料与Ａｌ２Ｏ３－ＳｉＣｗ－ＴｉＣ相比具有更高的综合机械性能。碳化钛在基体中形成连续的骨架阻碍晶粒的长大，随着碳化钛含量的增加，基体的硬度明显增加。主要强韧化机理有相变增韧、晶须拔出、载荷转移、裂纹偏转等。基体的主要断裂方式为穿晶解理断裂。     

温度对喷射成形7075+TiC铝合金触变成形的影响

采用Gleeble-1500热模拟机,对原位反应喷射成形7075 TiC铝合金进行半固态压缩变形,通过扫描电镜观察其变形后纵横截面的组织,用Imagetool软件及平均截线法统计晶粒尺寸.研究表明,晶粒尺寸随着变形温度的升高而增大,对应580～620℃的变形温度,晶粒尺寸分布范围为10～21 μm;当变形温度为610℃,变形速率为1 s-1时,合金表现出良好的半固态触变成形性能.     

原位颗粒含量对半固态7075铝合金组织的影响

制备具有不同原位TiC颗粒含量的喷射沉积7075铝合金,在610℃和620℃进行二次加热并保温30min,淬火固定半固态组织.采用扫描电镜观察其组织,利用平均截线法统计其晶粒尺寸,分析不同颗粒含量对喷射沉积7075铝合金半固态组织的影响规律.结果表明:当TiC颗粒含量达到2.91%(体积分数)时已经产生良好的钉扎效果,使得合金基本保持喷射沉积组织特征,能够满足后续的半固态成形工艺要求;TiC颗粒含量超过2.91%后,晶粒尺寸会进一步减小,但晶界上的颗粒明显增多并呈网状分布;TiC颗粒含量小于2.91%时,局部区域发生晶粒的异常长大现象,使合金组织的均匀化程度下降.     

三维大孔/介孔碳-碳化钛复合材料用于无枝晶锂金属负极

金属锂具有超高的理论容量(3860 mAh·g^-1)和低氧化还原电位(-3.04 V vs.标准氢电极),是极具吸引力的下一代高能量密度电池的负极材料。然而,循环过程中的体积膨胀、锂枝晶生长和“死锂”等问题严重的限制了其实际应用。合理设计三维骨架调控金属锂的成核行为是抑制锂枝晶生长的有效策略。本文中,我们发展了一种“软硬双模板”的方法合成了兼具大孔和介孔的三维碳-碳化钛(Three-dimensional macro-/mesoporous C-TiC,表示为3DMM-C-TiC)复合材料。多级孔道为金属锂的沉积提供了足够的空间,缓冲充放电中巨大的体积变化。此外,TiC的引入显著增强多孔骨架的导电性,改善锂金属的成核行为,促进金属锂的均匀成核和沉积,抑制锂枝晶生长。3DMM-C-TiC||Li电池测试表明,在循环300圈以后,库伦效率仍保持在98%以上。此外,所得材料与LiFePO₄ (LFP)组成的全电池也表现出优异的倍率和循环性能。本工作为无枝晶锂金属负极的设计提供了新的思路。     

In-Situ Synthesis and Characterization of Nanocomposites in the Si-Ti-N and Si-Ti-C Systems

The pyrolysis (1000 °C) of a liquid poly(vinylmethyl-co-methyl)silazane modified by tetrakis(dimethylamido)titanium in flowing ammonia, nitrogen and argon followed by the annealing (1000–1800 °C) of as-pyrolyzed ceramic powders have been investigated in detail. We first provide a comprehensive mechanistic study of the polymer-to-ceramic conversion based on TG experiments coupled with in-situ mass spectrometry and ex-situ solid-state NMR and FTIR spectroscopies of both the chemically modified polymer and the pyrolysis intermediates. The pyrolysis leads to X-ray amorphous materials with chemical bonding and ceramic yields controlled by the nature of the atmosphere. Then, the structural evolution of the amorphous network of ammonia-, nitrogen- and argon-treated ceramics has been studied above 1000 °C under nitrogen and argon by X-ray diffraction and electron microscopy. HRTEM images coupled with XRD confirm the formation of nanocomposites after annealing at 1400 °C. Their unique nanostructural feature appears to be the result of both the molecular origin of the materials and the nature of the atmosphere used during pyrolysis. Samples are composed of an amorphous Si-based ceramic matrix in which TiN_xC_y nanocrystals (x + y = 1) are homogeneously formed “in situ” in the matrix during the process and evolve toward fully crystallized compounds as TiN/Si₃N₄, TiN_xC_y (x + y = 1)/SiC and TiC/SiC nanocomposites after annealing to 1800 °C as a function of the atmosphere.     

石墨基体等离子喷涂TiC涂层耐烧蚀性能研究

采用等离子喷涂方法在石墨基体上制备出较为致密的Mo黏结层和TiC耐烧蚀涂层,利用SEM,XRD表征氧乙炔烧蚀试验前后涂层的表面形貌与相结构.结果表明:随着烧蚀距离减小,涂层质量烧蚀率呈现先增加后减小的趋势,最终趋于稳定;随着烧蚀时间增大,致密化区域快速增大,涂层质量烧蚀率略有增加.烧蚀过程中涂层经历了点状熔融、线形连接、网状连接和完全致密4个过程.TiC涂层在高温燃流作用下氧化生成TiO2并熔融,在燃流冲刷和表面张力作用下发生黏性流动,形成TiO2致密层,从而减小了机械剥落,降低了涂层质量烧蚀率.