A new rule of vibration sampling for predicting acoustical radiation from rectangular plates

Structural surface velocity distribution is often used to predict structural borne sound radiation. However the sampling interval of velocity should be chosen carefully to increase the prediction accuracy and to reduce the system cost. In this paper, several factors affecting the sampling interval are theoretically analyzed and discussed for a vibrating baffled rectangular plate. A new rule for the determination of the sampling interval is formulated. Using this rule, the results from both numerical simulations and experiments may be explained well.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

CPI趋势测定与分析

近期,居民消费价格指数(CPI)呈线性增长态势,形成通胀压力.经过建立数学模型测定,以及定性分析对定量分析结果的修正,可以预见,CPI增幅将会突破5%,且今后一段时期内,CPI仍会处在增幅5%以上的高位波动,通胀压力仍然存在,但CPI的上升空间有限.     

The benefit of practice for sound localization without sight

An experiment was designed to determine whether normally sighted human subjects would be able to adapt to the handicapping effects of sudden deprivation of visual cues on horizontal plane sound localization. Two groups of sighted normal-hearing young adults participated. One group was allowed the benefit of sight. The other group was blindfolded. Measurements of accuracy and the time to respond were made daily over the course of five consecutive days, in a semi-reverberant sound proof booth that modeled listening in a small office. Sound localization was assessed using an array of eight speakers that surrounded the subject in space. Each day, one block of 120 trials was presented for each of three stimuli, two one-third octave noise bands, centred at 0.5 and 4 kHz, and broadband noise, to assess the utilization of interaural temporal difference cues, interaural level difference cues and binaural and spectral cues in combination. Blindfolded subjects were relatively less accurate than sighted subjects. Both groups showed gains with practice, the blindfolded group to a greater degree, largely due to improvements in the use of spectral cues. The blindfolded group took longer to respond than the sighted group, but showed greater decrements in response time with practice.     

Research on sound radiation from body in free field

I.IntroductionWhenastructurcvibratcs,itsvibratingsurfacewillmakesurroundingmediummovetogethcrwithit.Ifthernotionissofastthatthcmediumroundthestructureproduccaloca1contractionandcxpansionandthcypropagatefaraway,thesoundradiationisformed.Itispossiblctodcscribeanalytica11ytheradiationfic1dofsimplyandregularlyshapcdsourcessuchaspointsoundsourccs,spherica1soundsourccsandinflnite1engthllnearsoundsourccs,butitisa1mostimpossib1ctosolvetheradiationfiledbyanyanalyt-ica1methodforsourcesofvcrycomplicateds…     

Simulation and fabrication of carbon nanotubes field emission pressure sensors

A novel field emission pressure sensor has been achieved utilizing carbon nanotubes (CNTs) as the electron source. The sensor consists of the anode sensing film fabricated by wet etching process and multi-wall carbon nanotubes (MWNTs) cathode in the micro-vacuum chamber. MWNTs on the silicon substrate were grown by thermal CVD. The prototype pressure sensor has a measured sensitivity of about 0.17-0.77 nA/Pa (101-550 KPa). The work shows the potential use of CNTs-based field-emitter in microsensors, such as accelerometers and tactile sensors.     

Acoustic characterization and prediction for fan-duct-plenum-room integrations

This paper investigates mutual influence of duct and room acoustics in the whole fan-duct-plenum-room integrations. Applying the parametric design language of finite element software ANSYS (APDL), dimensional and positional influence on system acoustics has been studied. Models with different room dimensions, duct lengths, duct cross-sections, duct locations, duct discharges and duct elbow were constructed, and their characteristics were compared qualitatively. Results show that small rooms, short ducts, large duct cross-sections and bell mouth duct discharges help to increase room sound pressure levels (SPLs); SPLs in ducts and plenums are sensitive to duct dimensions and duct discharge types but insensitive to duct locations and room dimensions; duct elbows have relatively indistinct acoustic influence in each component. Based on the calculation results, a semi-experimental method was proposed for simply and approximately evaluating indoor acoustic spectra of fan-duct-plenum-room integrations, then an example was used to demonstrate the prediction process. Finally, by adopting several ideal models, sound field constitutions, duct and room wall admittances and duct end reflection were explored quantitatively. This study may give a detailed understanding of fan-duct-plenum-room acoustics for researchers, also it might provide a new, simple and approximate prediction method for professionals to evaluate and improve fan-ducted acoustics.     

Experimental identification of physical parameters of fluid-filled pipes using acoustical signal processing

A method is formulated for the identification of an unknown physical parameter of a fluid-filled pipe using the measurement of sound speed in the pipe. The method uses a simple formula which provides the relationship between the sound speed and a few physical parameters of the pipe: thickness, diameter, wall material constants and fluid constants. Once the sound speed in the pipe is measured, the simple formula can be used to extract one of the unknown parameters providing the remaining ones are known.The sound speed in the pipe is measured using a 3-transducer array. In order to demonstrate the potential of the technique the results of several measurements obtained in a water-filled steel pipe are presented.The required accuracy of the measurement of sound speed and of the specification of known parameters is analysed. The accuracy depends on the unknown parameter which is to be identified. For example, if the pipe thickness is the unknown parameter, the other parameters have to be known within a very narrow margin of error. On the contrary, if the fluid properties have to be identified the needed accuracy of known parameters gets much lower.     

Improved convergence of a non-perturbative semi-classical pressure broadening model

It is shown that by including the second term of Magnus expansion, improved convergence can be achieved for the non-perturbative pressure broadening formalism proposed by Neilson and Gordon (J. Chem. Phys. 58 (1973) 4131). The present method was applied to the line broadening calculations of CO in a bath of Ar.     

The effect of construction material, contents and room geometry on the sound field in dwellings at low frequencies

An experimentally validated finite element method is used to model the sound level in rooms at low frequencies. It is demonstrated that the dimensions of rectangular rooms strongly influence the sound pressure level difference. Additional factors were investigated which are not normally considered in the frequency range where diffuse sound field conditions can be assumed. Three effects were investigated: room damping due to wall vibrations, furniture, the effect of small deviations from simple rectangular shapes. It is confirmed by field measurements that the vibrations of masonry walls and floors introduce less damping than surfaces of lightweight construction. Assigning to the FE model a damping equivalent to a surface absorption of 0.02 reproduces the effect of walls of heavyweight construction. Damping equivalent to a surface absorption of 0.15 reproduces the effects of plastered timber-frame walls, floors and ceilings. The work was briefly extended to a room pair built with heavyweight and lightweight material of construction. The modification of the shape of the room frequency response highlights well the effect of material of construction. In-situ and laboratory measurements show that furniture has little effect on steady-state room response below 100 Hz. Modelling a wall recess smaller than 0.5 m improved the agreement between prediction and measurements but the assumption of a simple rectangular room remains appropriate.