Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

聚偏氟乙烯共混体系的压电性及其分子运动——Ⅱ.PVDF与 P(VDF-HFE)以及PVDF与P(VDF-TFE)的共混体系

本文研究了 PVDF-P(VDF-HFE)以及 PVDF-P(VDF-TFE)共混体系的压电、介电、力学松弛谱。其松弛转变过程基本与 PVDF 的相似。α,β,γ压电松弛峰分别位于40～120℃,-40℃,-85℃附近。实验结果表明后一体系的压电性大于前一体系的。同时,PVDF-P(VDF-TFE)的压电性也大于PVDF-PMMA 共混体系的。选择第二组分时,以介电常数高,模量小而本身又具有压电性的,更有助于共混薄膜压电性的提高。在同样的极化条件下,经拉伸的 P(VDF-TFE)薄膜,其压电性大于未经拉伸的薄膜,这表明分子的取向对薄膜的压电性也有影响。TSC 表明,42℃的松弛峰与晶区表面捕获的空间电荷有关,对压电性也有一定的贡献。     

PVDF应力传感器的设计、标定及其在混凝土冲击试验中的应用

利用分离式霍普金森杆(SHPB)试验技术对PVDF应力传感器进行了压电系数的动态标定,标定值为27.21 PC/N.在落锤冲击试验机上完成了预埋PVDF应力传感器的混凝土圆柱体试件的轴向冲击试验,并利用PVDF应力传感器信号和试件轴向压缩曲线得到了混凝土在冲击加载条件下的动态应力应变曲线.由于混凝土试件在冲击加载过程中应力分布不均匀,预埋在试件中心的PVDF应力传感器测试的应力结果比用锤头冲击力计算出来的试件平均应力稍大.     

利用PVDF设计两维简支结构声辐射模态传感器

PVDF(polyvinylidenefluoride聚偏氟乙烯 )是一种新型的压电高分子材料 ,它不仅密度低 ,而且具有较强的压电性 ,机械性、可塑性好等特点 用特定形状的PVDF薄膜作为误差传感器 ,将它贴在结构体表面上时 ,对系统产生很小的影响 笔者在声辐射模态理论以及两维分布式压电传感器方程的基础上 ,利用PVDF独特的积分特性 ,以简支矩形板为例 ,设计了PVDF压电薄膜传感器用于测量简支板第一、二阶声辐射模态伴随系数 并在理论上进行数值分析比较可知 ,这种特定形状的PVDF薄膜作为误差传感器是可行的     

振动板声辐射模态伴随系数的测量

以工程常见四端位移为零的振动板为例,提出一种新的压电式传感器的设计方法测量第一阶声辐射模态伴随系数．利用特定形状的PYDF（Polyvinylidene fluoride聚偏氟乙烯）薄膜作为误差传感器,使PVDF输出信号为所需要的第一阶声辐射模态伴随系数．结果表明PVDF传感器不仅适用四边简支,四边固定以及介于两者之间的边界条件板结构,而且所设计的PVDF形状作为误差传感器对振动结构表面振速分布变化十分敏感．试验数据表明利用PVDF传感器测量振动结构第一阶声辐射模态伴随系数是可行的。     

Thermal properties and structure of electrospun blends of PVDF with a fluorinated copolymer

We report the structure and thermal properties of blends comprising poly(vinylidene fluoride) (PVDF) and a random fluorinated copolymer (FCP) of poly(methyl methacrylate)‐random‐1H,1H,2H,2H‐perfluorodecyl methacrylate, promising membrane materials for oil–water separation. The roles of processing method and copolymer content on structure and properties were studied for fibrous membranes and films with varying compositions. Bead‐free, nonwoven fibrous membranes were obtained by electrospinning. Fiber diameters ranged from 0.4 to 1.9 μm, and thinner fibers were obtained for PVDF content >80%. As copolymer content increased, degree of crystallinity and onset of degradation for each blend decreased. Processing conditions have a greater impact on the crystallographic phase of PVDF than copolymer content. Fibers have polar beta phase; solution‐cast films contain gamma and beta phase; and melt crystallized films form alpha phase. Kwei's model was used to model the glass transition temperatures of the blends. Addition of FCP increases hydrophobicity of the electrospun membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 312–322     

Predicting Polymorphism of Electrospun Polyvinylidene Fluoride Membranes by Their Morphologies

Although electrospinning of polyvinylidene fluoride (PVDF) has been studied for more than 10 years, the crystalline phase differentiation of the electrospun mats is still normally through the combination of different characterization techniques, and the relationship between polymorphism and morphology of the fibers in electrospun PVDF membranes has never been reported. Here, we show their close relationships by conducting room-temperature electrospinning experiments on various polymer/solvent systems. The electrospun membranes full of bead-free fibers have a very high fraction of β-phase, F(β), over 90%, and high orientation, whereas the membranes comprising beads and/or a large number of beaded fibers most often result in a low fraction of β-phase (F(β) normally below 50%) and low orientation. On the other hand, electrospun membranes consisting of both bead-free fibers and a very limited number of beaded fibers showed a medium high fraction of β-phase, F(β) more than 70% but less than 90%. These findings suggest the feasibility of intuitively predicting the crystalline phase of electrospun PVDF membranes directly by their morphologies, which is obviously simple, inexpensive and convenient for future investigations.     

Synergic effect in electrical conductivity using a combination of two fillers in PVDF hybrids composites

The objective of this work was to prepare novel conductive blends of poly(vinylidene fluoride) (PVDF) with polypyrrole (PPy) and to compare their performance with PVDF/multiwall carbon nanotube (MWCNT) composites and novel PVDF/PPy/MWCNT hybrid systems. All the compositions were prepared by melt mixing using a miniature mixer. The mixtures were characterized by Fourier transformed infrared (FTIR), wide angle X-ray diffraction (WAXD), thermogravimetric analyses (TGA), scanning and transmission electron microscopy (SEM and TEM, respectively) and volume electrical resistivity. For the binary PVDF/PPy and PVDF/MWCNT systems, percolation thresholds of 10 and 0.3 wt%, respectively, were found. In the hybrid systems, however, the percolation threshold for each filler was lower than in the binary systems, but the electrical conductivities were always much higher at all concentrations than the conductivities of the binary systems. Therefore, the addition of both fillers had a synergistic effect on the hybrid system conductivity, which was attributed to its morphology: the PPy increased the homogeneity of the MWCNT distribution and decreased the available free volume for the MWCNT; as a result the MWCNT rolled around the PPy particles bridging them through the PVDF matrix, increasing the quantum tunneling effect and thus, the electrical conductivity of the system.     

Broadband dielectric characterization of piezoelectric poly(vinylidene fluoride)thin films between 278 K and 308 K

This work describes the dielectric properties of piezoelectric poly(vinylidene fluoride) (PVDF) thin films in the frequency and temperature ranges relevant for usual applications. We measured the isothermal dielectric relaxation spectra of commercial piezoelectric PVDF thin films between 10 Hz to 10 MHz, at several temperatures from 278 K to 308 K. Measurements were made for samples in mechanically free and clamped conditions, in the direction of the poling field (perpendicular to the film). We found that the imaginary part of the dielectric relaxation spectra of free and clamped PVDF samples is dominated by a peak, above 100 kHz, that can be characterized by a Havriliak-Negami function. The characteristic time follows an Arrhenius dependence on temperature. Moreover, the spectra of the free PVDF samples show two additional peaks at low frequencies which are associated with mechanical relaxation processes. Our results are important for the characterization of piezoelectric PVDF, particularly after the stretching and poling processes in thin films, and for the design and characterization of a broad range of ultrasonic transducers.