Microstructure of laser melted Al18B4O33w/2024Al composite

The microstructure of a laser treated Al₁₈B₄O₃₃w/2024Al composite has been investigated using transmission electron microscope (TEM), low-angle (glancing angle) X-ray diffraction (XRD) techniques. Various surface microstructures were observed in the laser treated composite. The Al₁₈B₄O₃₃ whisker on the surface of the composite was decomposed during laser surface melting, various decomposition products were studied in the laser treated composite. Eutectic phases and the precipitation in the matrix of the composite with laser-treated were observed. The main phases detected in the molten zone were aluminum and decomposition products Al₂O₃. The effect of laser treatment on the hardness of the composite was also examined. A surface hardness of 400 Hv was noted.     

Sol–gel preparation and properties of hydroxypropylcellulose–titania hybrid thin films

Hydroxypropylcellulose (HPC)–titania hybrid thin films were prepared by sol–gel method where titanium tetraisopropoxide Ti(OC₃H₇ ⁱ )₄ was hydrolyzed under acidic conditions in the presence of HPC, followed by dip-coating and drying at 120 °C for 24 h. The viscosity average molecular weight of HPC was 55,000–70,000 or 110,000–150,000, and the TiO₂/(HPC + TiO₂) mass ratio ranged from 0 to 1, which was calculated on the assumption that all Ti(OC₃H₇ ⁱ )₄ is converted into TiO₂. The films were 0.35–1.0 μm thick, transparent in visible region and opaque in ultraviolet (UV) region, where the optical absorption coefficient in UV region increased with increasing titania content. The refractive index increased with increasing titania content, ranging from 1.6 to 1.8 for the hybrid thin films. The pencil hardness increased from 6B to 5H, the durability in hot water significantly increased and the contact angle of water on films increased from 35° to 89° with increasing titania content. Crack-free films could be deposited on organic polymer substrates irrespective of titania or HPC contents, where cracking did not occur at higher HPC contents even when the substrate was bent.     

Determination of uncertainty for hardness measurement: proposal of the standard,available software

After the next revision of the ISO-standards for hardness testing (ISO 6506–6508) an estimation of the uncertainty (ISO/IEC 17025, ISO 5725) is mandatory. The two proposed approaches of part one (ISO 6506–6508) of the ISO Standards for hardness are exemplified. The calculation approach implemented in an Excel-based file, which is available via , is announced.Presented at the Metro Trade Workshop on Traceability and Measurement Uncertainty in Testing, 30–31 January 2003, Berlin, Germany     

Design and fabrication of multi-layers infrared antireflection coating consisting of ZnS and Ge on ZnS substrate

We have designed, fabricated and characterized a multi-layers antireflection coating on multispectral ZnS substrate, suitable for the infrared range of 8–12 μm. The 4-layers coating (Ge/ZnS/Ge/ZnS) with optimized thicknesses was fabricated by PVD technique and studied by FTIR, nanoindentation and AFM. From FTIR spectroscopy it was found that, in the wavelength range of 8–12 μm, the average transmittance of the double-side coated sample increases by about 26% and its maximum reaches about 98%. To improve the mechanical hardness, a bilayer of Y₂O₃/carbon was deposited on the coating. Nanoindentation test shows that the coating enhances the mechanical properties. The final coating have successfully passed durability and environmental tests.     

Synthesis and Polymerization of N-(L-Menthylcarboxylatomethyl)maleimide

A new type of optically active N-(L-menthylcarboxylatomethyl)maleimide (MGMI) was synthesized from maleic anhydride, glycine, and L-menthol. Radical homopolymerization of MGMI was performed at 50°C for 24 h to give optically active polymer having [α]_D = -57°. Radical copolymerizations of MGMI (M ₁) were performed with styrene (ST, M ₂), methyl methacrylate (MMA, M ₂) in benzene at 50°C. From the results, the monomer reactivity ratios (r ₁, r ₂) and the Alfrey-Price Q, e values were determined as follows: r ₁ = 0.16, r ₂ = 0.006 for the MGMI-ST system; r ₁ = 0.15, r ₂ = 1.65 for the MGMI-MMA system, and Q ₁ = 0.72, e ₁ = 1.59 calculated from the MGMI-MMA system. Anionic homopolymerizations of MGMI were also carried out. Chiroptical properties of the polymers were investigated.     

Fabrication of high-performance nickel/graphene oxide composite coatings using ultrasonic-assisted electrodeposition

Ultrasonic-assisted electrodeposition was used to fabricate the nickel/graphene oxide composite coatings with high hardness, low friction coefficient, and high wear resistance. In the present study, the effects of ultrasonic power and concentration of graphene oxide on the mechanical and tribological properties of the electrodeposited nickel/graphene oxide composite coatings were systematically studied. X-ray diffraction (XRD) analyses showed that the crystallite size of the nickel decreased with an increase of ultrasonic power (0–50 W, 40 KHz, square wave) and concentration of graphene oxide (0.1–0.4 g/L). Morphologies of the surface and cross-section of the composite coatings observed by Scanning Electron Microscopy (SEM) confirmed the existence of graphene oxide particles in the nickel matrix. The results from microhardness measurement demonstrated that the hardness was increased by 1.8 times using 50 W ultrasonic-assisted electrodeposition with the fixed concentration of graphene oxide (0.1 g/L), compared to the pure nickel coating. The hardness was increased by 4.4 times for the 0.4 g/L graphene oxide with the optimized ultrasonic power of 50 W in comparison to the pure nickel coating. Meanwhile, the friction coefficient decreased gradually with an increase in ultrasonic power and concentration of graphene oxide, respectively, where the effect of the concentration of graphene oxide played a more important role.     

Surface modification of pure titanium by pulsed electron beam

The microstructure, hardness and corrosion resistance of commercially pure Ti treated by low energy high current pulsed electron beam (LEHCPEB) have been investigated. The thin near-surface melted layer rapidly solidified into β and subsequently transformed into ultrafine α′ martensite. This has led to a drastic improvement of the corrosion properties and a significant increase (more than 60%) in hardness of the top surface.     

具有失稳分解强化的Hall-Petch关系

对Cu30Ni25Fe合金,采用变形和热处理的方法获得了不同的晶粒度和失稳分解组织,研究了失稳分解相界对HallPetch关系的影响·结果表明,合金发生失稳分解后,其硬度和晶粒直径的关系仍符合HallPetch关系式·在各种晶粒度下失稳分解后的硬度均大于固溶态,但当分解后的两相尺寸与晶粒尺寸相比约小两个数量级时,失稳分解的相界强化作用消失·失稳分解组织的细晶硬化系数KHV值明显低于固溶态,且随失稳分解强化作用的增大而降低,这反映了失稳分解后合金的强度对晶粒大小的敏感程度降低·     

镍磷合金镀层的强化性能与机制

本文借助于DSC热扫描仪、电子显微镜和硬度计等仪器,研究了化学沉积镍磷合金镀层的强化性能和机制。试验结果表明,随着镀层的磷含量增加,镀层硬度上升,然后下降;在热处理过程中,镀层的硬度变化经历了一个最大值过程,最高硬度出现在400℃。低磷镀层表现为沉淀强化过程,高磷镀层产生分散强化作用。     

Intrinsic mechanical properties of ultra-thin amorphous carbon layers

In this work, we extracted the film's hardness (H_F) of ultra-thin diamond-like carbon layers by simultaneously taking into account the tip blunting and the substrate effect. As compared to previous approaches, which did not consider tip blunting, this resulted in marked differences (30-100%) for the H_F value of the thinner carbon coatings. We find that the nature of the substrate influences this intrinsic film parameter and hence the growth mechanisms. Moreover, the H_F values generally increase with film thickness. The 10 nm and 50 nm thick hydrogenated amorphous carbon (a-C:H) films deposited onto Si have H_F values of, respectively, ∼26 GPa and ∼31 GPa whereas the 10 nm and 50 nm thick tetrahedral amorphous carbon (t-aC) films deposited onto Si have H_F values of, respectively, ∼29 GPa and ∼38 GPa. Both the a-C:H and t-aC materials also show higher density and refractive index values for the thicker coatings, as measured, respectively by X-ray reflectometry and optical profilometry analysis. However, the Raman analysis of the a-C:H samples show bonding characteristics which are independent of the film thickness. This indicates that in these ultra-thin hydrogenated carbon films, the arrangement of sp² clusters does not relate directly to the hardness of the film.