On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

产品原理方案的功能设计法──“管接头标记自动压印机”的原理方案设计

本文通过“管接头标记自动压印机”原理方案的构思过程，说明产品原理方案设计的功能论方法的一般原理和特点及其应用。     

SSIMS analysis of organics, polymer blends and interfaces

This paper gives a critical review on the applications of ToF SIMS in the areas of polymer additive characterization and in the study of polymer blends and interfaces. Polymer additives can readily be identified by ToF SIMS using their parent molecular ions or characteristic fragments. This analytical capability has been successfully applied to monitor the migration or segregation of additives during polymer processing. ToF SIMS is an ideal analytical tool for the study of polymer blends and interfaces because it is able to provide information on both surface composition and morphology. In combination with other analytical techniques such as AFM and XPS, ToF SIMS chemical imaging capability has opened up new horizons in the investigation of complex polymer blend systems. Finally the main advantages and limitations of ToF SIMS in these application areas are also discussed.     

Structural and optical characterization of the propolis films

We have performed structural and optical characterizations of the propolis (an organic entity of biological nature) films grown on various non-organic substrates. The films were grown from a propolis melt or a propolis alcohol solution. The crystal structure has been observed in the films precipitated from the solution onto substrates such as an amorphous glass and sapphire or semiconductor indium monoselenide. For any growth method, the propolis film is a semiconductor with the bandgap of 3.07 eV at 300 K that is confirmed by a maximum in photoluminescence spectra at 2.86 eV. We argue that propolis films might be used in various optoelectronic device applications.     

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius~2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm~3, space group P12_1/al.     

Morphology-dependent photoluminescence property of red-emitting LnOCl:Eu (Ln=La and Gd)

Three different synthetic methods, the liquid phase process in HCl solution, the solvothermal reaction, and the surfactant-assisted solvothermal reaction, were explored to selectively control the particle shape and to enhance the luminescence intensity of the PbFCl-type red-emitting oxychloride phosphors LnOCl:Eu (Ln=La and Gd). The solvothermal pressure facilitated the low-temperature crystallization of the rod-shape particles for both Ln=La and Gd. It is noted that LaOCl:Eu nanorods show highly porous particle surface and quite low photoemission intensity. In contrast, the solvothermal synthesis could highly enhance the red-emission of GdOCl:Eu with no porous surface so as to be comparable to that of commercial Y₂O₃:Eu phosphor. An addition of surfactant material during solvothermal reaction yielded a rhomboidal-shape phosphor particles with no porous surface for both Ln=La and Gd. Interestingly, the elimination of surface porosity by using a surfactant significantly increased the emission intensity of LaOCl:Eu. It is proposed that the application of solvothermal technique for the synthesis of the PbFCl-type oxychloride phosphors is very effective to selectively control the particle shape and consequently to enhance the photoemission intensity if we use an appropriate surfactant material.     

胆甾液晶／聚合物多组分体系的结构与性能研究（Ⅲ）──ChN／poly（MMA－CO－BMA）混合体系的形态结构

应用Ｘ射线衍射、偏光显微镜及电子显微镜研究了胆甾液晶与甲基丙烯酸甲酯（ＭＭＡ）─甲基丙烯酸丁酯（ＢＭＡ）无规共聚物共混体系的形态结构。研究了体系的结晶态及液晶态的行为和共聚物含量及组成对光学织构的影响。     

Morphological effect on spectral property of poly(9,9-dihexylfluorene-alt-2,5-dihexyloxybenzene) films

In this study the optical property and film morphology of a conjugated polymer, poly(9,9-dihexylfluorene-alt-2,5-dihexyloxybenzene) (PF6OC6), are investigated. It is found that the intensity of the 0-1 emission relative to the 0-0 emission in the PL spectra and the full width at the half-maximum (fwhm) of PL spectra of the PF6OC6 films decrease firstly and then increase with increasing the annealing temperature. The polymer films also exhibit different morphological features after annealing at different temperatures. The optical and morphological results suggest that the vibronic structure of PF6OC6 is closely related to the film morphology, and its formation is enhanced in the amorphous (or less ordered) films and inhibited in the ordered films.     

Organic–inorganic nanocomposites prepared from fluoro-aramid and silica

Fluoro-aramid-based sol/gel-derived nanocomposites were synthesized by condensing a mixture of 4,4′-(hexafluoro-isopropylidene)dianiline and 1,3-phenylenediamine with terephthaloylchloride (TPC) in dimethylacetamide. TPC was added in slight excess to produce amide chains with carbonyl chloride end groups and then replaced with alkoxy groups using aminophenyltrimethoxysilane to develop bonding with the silica network. Mechanical, dynamic mechanical thermal, water absorption and morphological measurements were carried out on the thin hybrid films. Increase in the tensile strength and modulus was observed as compared to pristine polyamide. The thermal decomposition temperature was found in the range of 400–500 °C. The water absorption was found to be reduced with higher silica content. The glass transition temperature and the storage moduli increased with increasing silica concentration. The maximum increase in the T _g value (345 °C) was observed with 20 wt% silica. Scanning electron microscopy revealed the uniform distribution of silica in the matrix with an average particle size ranging from 8 to 50 nm.     

聚甲醛自然老化的SEM研究

对户外曝晒3～36个月的聚甲醛(POM)老化形态进行了研究,讨论了老化层厚度,裂纹宽度、裂纹深度及断口形态与老化时间的关系。结果表明:POM的老化导致了材料内部结构由韧性变成脆性而几乎完全丧失物理机械性能。