Facile fabrication of fast recyclable and multiple self‐healing epoxy materials through diels‐alder adduct cross‐linker

A reversibly cross‐linked epoxy resin with efficient reprocessing and intrinsic self‐healing was prepared from a diamine Diels‐Alder (DA) adduct cross‐linker and a commercial epoxy oligomer. The newly synthesized diamine cross‐linker, comprising a DA adduct of furan and maleimide moieties, can cure epoxy monomer/oligomer with thermal reversibility. The reversible transition between cross‐linked state and linear architecture endows the cured epoxy with rapid recyclability and repeated healability. The reversibly cross‐linked epoxy fundamentally behaves as typical thermosets at ambient conditions yet can be fast reprocessed at elevated temperature like thermoplastics. As a potential reversible adhesive, the epoxy polymer with adhesive strength values about 3 MPa showed full recovery after repeated fracture‐thermal healing processes. The methodology explored in this contribution provides new insights in modification of conventional engineering plastics as functional materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2094–2103     

SEPARATING SCN~- FROM DESULPHURIZATION WASTE SOLUTION OF COCKING PLANT BY D241 RESIN

1. INTRODUCTION In the process of coking plant, about 30%~35% sulfur is transformed to H2S and some other sulfide, which form impurity in coal gas together with NH3 and HCN. Only 0.1% H2S containing in air can lead to die, so it is very important to carry on desulphurization and decyanation with coal gas [1~3]. Currently desulphurization and decyanation craft technique have Dry Oxidation Technology, Wet Oxidation Technology and Liquid Absorption Technology [2] three main kinds. The…     

Proton conductivity of phosphoric acid derivative of fullerene

The proton conductive property of methano [60] fullerene diphosphoric acid has been investigated under various humidity conditions at the temperature range between 15 and 45 °C. It shows proton conductivity as high as 10⁻² S cm⁻¹ at 25 °C under relative humidity of 95%. Thermal analyses including TG–DTA and thermal desorption mass spectroscopy (TDS) confirm that the compound is thermally stable up to 200 °C. Proton conduction of the compound depends very much on humidity or water content. The logarithmic conductivity at 25 °C is increased linearly with increasing relative humidity. The activation energy (E_a) estimated from the slope of log(σT) vs. 1/T is decreased from 1.08 to 0.52 eV, as the relative humidity is increased from 40% to 75%. The humidity dependence of conductivity is discussed in the light of the observed hydration isotherm.     

离子交换富集-导数火焰原子吸收法测定自来水中Cu,Fe和Zn

本文研究了用 2 0 1× 7阳离子交换树脂对自来水中的微量元素进行交换富集 ,采用微量脉冲进样 导数火焰原子吸收法测定富集后溶液中的Cu ,Fe和Zn ,该方法灵敏度分别为 0 2 9,0 5 9和 0 0 6 μg·L- 1 ,精密度分别为 4 2 8% ,1 95 %和 2 2 8% ,检测限分别为 1 2 8,5 85和 0 6 8μg·L- 1 ,回收率分别为 91 13% ,10 1 34%和99 84 % ,本方法大大减少了需样量 ,简便快速 ,灵敏度高。     

Synthesis of bioactive indolocarbazoles: synthesis, nucleophilic ring-opening and chiral base desymmetrisation of a cyclic sulfate intermediate

A number of new functionalised bridged indolocarbazole systems have been prepared by ring-opening reactions of a key cyclic sulfate intermediate, prepared from the corresponding diol by the action of sulfuryl diimidazole and DBU. The same cyclic sulfate also undergoes an unprecedented asymmetric rearrangement to a chiral ketone, on treatment with a chiral lithium amide base.     

Free boundary viscous flows at micro and mesolevel during liquid composites moulding process

Numerical simulation aspects, related to low Reynolds number free boundary viscous flows at micro and mesolevel during the resin impregnation stage of the liquid composite moulding process (LCM), are presented in this article. A free boundary program (FBP), developed by the authors, is used to track the movement of the resin front accurately by accounting for the surface tension effects at the boundary. Issues related to the global and local mass conservation (GMC and LMC) are identified and discussed. Unsuitable conditions for LMC and consequently GMC are uncovered at low capillary numbers, and hence a strategy for the numerical simulation of such flows is suggested. FBP encompasses a set of subroutines that are linked to modules in ANSYS. FBP can capture the void formation dynamics based on the analysis developed. We present resin impregnation dynamics in two dimensions. Extension to three dimensions is a subject for further research. Several examples are shown and efficiency of different stabilization techniques are compared. Copyright © 2004 John Wiley & Sons, Ltd.     

UV‐ignited frontal polymerization of an epoxy resin

By combining frontal polymerization and radical‐induced cationic polymerization, it was possible to cure thick samples of an epoxy monomer bleached by UV light. The effect of the relative amounts of cationic photoinitiator and radical initiator was thoroughly investigated and was related to the front's velocity and its maximum temperature. The materials obtained were characterized by quantitative conversion also in the deeper layers, not reached by UV light. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2066–2072, 2004     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

New liquid‐crystalline poly(ester amide)s: The role of nitro groups in the phase behavior

New hydrogen‐bonded liquid‐crystalline poly(ester amide)s (PEA)s were obtained from 1,4‐terephthaloyl[bis‐(3‐nitro‐N‐anthranilic acid)] (5) or 1,4‐terephthaloyl[bis‐(N‐anthranilic acid)] (6), with or without nitro groups, respectively, through the separate condensation of each with hydroquinone or dihydroxynaphthalene. The dicarboxylic monomers were synthesized from 2‐aminobenzoic acid. The phase behavior of the monomers and polymers were studied with differential scanning calorimetry, polarized light microscopy, and wide‐angle X‐ray diffraction methods. Monomer 5, containing nitro groups, exhibited a smectic liquid‐crystalline phase, whereas the texture of monomer 6 without nitro groups appeared to be nematic. The PEAs containing nitro groups exhibited polymorphism (smectic and nematic), whereas those without nitro groups exhibited only one phase transition (a nematic threaded texture). The changes occurring in the phase behavior of the polymers were explained by the introduction of nitro groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1289–1298, 2004