Resistance reduction effect of potassium bismuth titanate doping in yttrium–manganese co-doped medium Curie temperature barium titanate lead free ceramics through improved synthesis process

Through improved synthesis process, resistance reduction effect of (K_0.5Bi_0.5)TiO₃ (KBT) doping in Y–Mn co-doped BaTiO₃ (BT) lead free ceramics was investigated. By different doping methods (doping K₂O, Bi₂O₃ and TiO₂ or synthesized KBT), medium Curie temperature (around 130 °C) lead free BT ceramics were obtained with ultra-low resistivity (13.84 Ωcm) with a temperature maintaining process at 700 °C. In this contribution, effect of sintering process and doping methods is discussed in detail.     

片式多层陶瓷微波谐振器

介绍了片式陶瓷微波谐振器的工艺过程、谐振器的结构以及结构对谐振器参数的影响,谐振器与外电路的耦合采用耦合间隙的方法与谐振单元在同一层内实现,这种新结构既可给制备工艺带来方便,又可减少工艺所带来的误差。用多层陶瓷工艺技术,用高介电常数、低温烧结微波陶瓷实现了中心频率为1GHz,有载品质因数大于80的试验双端口多层微波谐振器。微波谐振器体积小,整个谐振器的尺寸为7mm×2mm×1mm,适用于表面贴装技术。     

BaTiO_3系PTCR热敏电阻器用烧结助剂的研究

研究了烧结助剂的作用，实验结果表明：如只引入半导化元素，不引入烧结助剂，则室温电阻率ρ２５很大，甚至是绝缘体。由于烧结助剂的加入，既改善了ＰＴＣＲ热敏电阻陶瓷的烧结性，又改善了其ρ２５、耐电压Ｖｂ、ＰＴＣ效应等特性，从而使产品的各种特性易于重复。烧结助剂昔日多用ＡＳＴ，现在常用ＳｉＯ２，其加入量ｘ宜小于２％。ＳｉＯ２的纯度、杂质等化学特性，与粒子形状、粒度分布、晶系等物理特性，对ＰＴＣＲ热敏电阻器的电性能有很大的影响。据此提出了ＢａＴｉＯ３系ＰＴＣＲ热敏电阻器用ＳｉＯ２的技术标准。     

微球板电子倍增器基体制备技术研究

新型微球板电子倍增器和微通道板相比具有高增益、无离子反馈、制备简单、造价低廉等优点。介绍了微球板电子倍增器的工作原理、特点和广阔的应用前景。由于微球板基体的形成技术是微球板制备的关键技术，论文从理论上研究了微球板基体烧结过程中的烧结速率。并采用自行设计组分的高铅玻璃，用立式炉成珠设备进行了玻璃微珠的制备。探索了微球板制备过程中玻璃微珠的分级技术、微球板电子倍增器基体成型工艺和技术。制备出基本满足要求的微球板电子倍增器基体。给出了制造的样品和文献上样品结构的SEM对比照片，最后对实验过程中的一些现象进行了分析，并给出了实验的结论。     

Fabrication and properties of PLZT ceramics from spray-dried aqueous solution

PLZT ceramics with the composition of 9/62/38 (La/Zr/Ti) were fabricated from spraydried aqueous solution. Complete crystallization of the spray-dried powder is achieved after 1 hr calcination at 650‡ C as compared to 800‡ C, 1 hr for conventional mixedoxide method. Sintering environment plays an important role in the densification of PLZT ceramics. Densities of the atmosphere sintered samples are much higher than those of normal sintered ones. PLZT ceramics derived from spray-dried powders have properties comparable to those derived from sol-gel ones. The spray-dried method presents a less expensive and more effective approach in the synthesis of PLZT ceramics.     

ST－4型节能全自动辊道双推板窑

ＳＴ－４型全自动辊道双推板窑是为永磁铁氧体规模生产而研制的一种节能型空气烧结窑。它根据永磁铁氧体烧结的工艺要求，设计了合理的温区，使规模生产烧结成品率达９５％以上；采用辊道推板相结合的窑床形式与复合保温结构，达到了永磁铁氧体能耗１．２ｋｗｈ／ｋｇ；采用优化设计，使设备性能先进，稳定可靠。     

ZST微波陶瓷在介质振荡器上的应用研究

用传统固相法制备ZST(氧化锆-氧化锡-氧化钛)系微波陶瓷,研究了ZST系微波陶瓷的组成对介电性能的影响。通过X-射线衍射(XRD)和HP8714ET网络分析仪对其晶体结构和微波介电性能进行研究,实验结果表明:少量掺Bi2O3的ZST系陶瓷材料可把烧结温度降低至1 260℃,微波介电性能较好;掺入量大于2%(质量分数)时,ZST系微波陶瓷在晶界偏析形成了Bi2Ti2O7新相,微波性能下降。用微波介电性能较好的ZST系陶瓷制成的介质振荡器进行测试,其电性能满足设计要求。     

Nd掺杂的Bi4Ti3O12变温X射线衍射分析

利用变温X射线衍射技术，在预烧过程中分析了Nd掺杂Bi4Ti3O12后生成Bi3.15Nd0.85Ti3O12（BNT）相的形成过程以及微结构的变化．实验观察到以30℃／min的升温速率，BNT相在700℃时开始形成，其衍射峰强度随温度的继续升高而增强，衍射峰半高宽随烧结时间延长而减小．X射线衍射分析结果表明，在900℃恒温条件下，烧结约2h，可形成单一的BNT相．     

Modification of a three-way catalyst washcoat by aging: A study along the longitudinal axis

This work reports the research carried out by studying aliquots extracted at different axial coordinates from Three Way Catalyst (TWC) monoliths aged under real traffic conditions. Our study focused on the catalytic properties and on several chemical and physical effects caused in the Front and Rear monolith washcoat surfaces by vehicle aging after 60,000 km. Regarding the catalytic properties, all the used aliquots showed poorer activity than their corresponding fresh counterparts. The strongest deactivation was detected for NO and hydrocarbon conversion. CO conversion was less affected and the Rear monolith was as deactivated as the Front one. The characterisation techniques (TXRF, N₂ adsorption-desorption isotherms, XRD and H₂-TPR) detected - (i) the deposition of P, Zn and Pb; (ii) the formation of CePO₄ on account of the Ce from the washcoat; (iii) thermal sintering; (iv) inhibition of the reducibility of Ce oxides - as the main effects brought about by vehicle aging conditions. The deactivation observed at the beginning of the Front monolith was the result of a combination of the former effects. When moving downstream to higher axial coordinates, Pb accumulation and the loss of specific area appeared to be the only probable sources of deactivation.     

Y2O3薄膜处理对3Cr25Ni7N合金的抗高温氧化性能的影响

采用电沉积-热解法在3Cr25Ni7N合金表面制备了Y2O3薄膜,并研究了薄膜处理对合金在1000℃空气中的抗高温氧化性能的影响。氧化动力学曲线、SEM及XRD分析结果表明,Y2O3薄膜处理使合金表面氧化膜以尖晶石结构为主,氧化膜致密,有效地抑制了Cr2O3的挥发反应,且氧化膜与基体的附着性好,因此合金在高温下的抗氧化性能得到提高,这与氧化钇薄膜在较低温度下抗高温氧化性能提高的机制是不同的。在不同温度下,Y2O3薄膜处理均可以有效提高合金的抗高温氧化性能。