定向棱镜腔平顶高斯激光束特性的研究

在XeCl准分子激光器中,采用定向棱镜作为端反射镜与平面输出镜构成激光器谐振腔,获得了近场能量分布均匀、远场能量分布高度集中的相干平顶高斯激光束输出,并具有腔镜高抗失调能力,改善了激光束质量。     

热致型胆甾酯液晶的相变研究

使用偏光显微镜观察胆甾烯壬酸酯液晶的相变，发现在不同的温度变化条件下液晶相变过程是不同的．本文讨论了其变化规律．     

Mesoscopic details of crack tip deformation field by application of differential interference contrast method

An experimental method is developed to examine the near tip deformation at the mesoscopic scale level. The differential interference contrast (DIC) method is used by application of the Nomarski prism in polarized microscope for measuring the out of surface deformation. The method is very sensitive to small height changes detected by different interference color. Discussed are results for the crack tip deformation field.     

薄膜偏振分光镜的研究

概述薄膜偏振分光镜的研究现状及其主要特点，重点分析薄膜偏振分光镜的设计原理,并利用等效折射率的方法计算中心波长的反射率．     

空气隙间隔格兰型棱镜偏光器透射光强扰动的温度效应

线偏振光正入射的情况下，空气隙间隔格兰型棱镜的透射光强随旋转角出现周期性增强的扰 动.扰动的出现影响了透射偏振光的质量.研究表明，透射光强对入射角有着敏感的依赖关系 .实验中空气隙间隔格兰型棱镜的振动引起入射角在棱镜的结构角附近作微小变化，从而导 致了透射光强的扰动.讨论了温度的变化对扰动大小的影响.给出了减小扰动的有效方法. 关键词： 偏光棱镜 热光效应 干涉 扰动     

90°分束偏光镜光强分束比研究

给出了90°分束偏光镜的e,o光光强分束比的计算公式,以及光强分束比随光波长的变化曲线;在6328Å测得的光强分束比与计算值是一致的。     

界面反射偏振象差分析

在光学没计中,一般认为在同一光波面上,光束具有相同的振幅和偏振状态。事实上,光束经过许多光学元件后,偏振状态会发生变化,特别是入射角和光程的不同,会导致出射光波面上偏振分布不再均匀,形成偏振象差。本文主要就轴上物点发出的光束经过界面反射后的偏振象差方面进行了分析。     

Polarization transforming properties of Dove prisms

We analyze the polarization changes introduced by a rotated Dove prism on the linearly polarized light, using the Jones calculus and the exact ray trace analysis. The state of polarization changes from the linear to a mildly elliptical one when a plane wave front passes through a rotated Dove prism: its semi-major axis is nearly parallel to the input plane of polarization, for any angle of prism rotation. The interferogram contrast remains high for all shearing angles in spite of polarization changes when the Dove prism is incorporated into a rotational shearing interferometer. These results are confirmed experimentally.     

改进型迈克耳孙干涉仪

采用分光梭镜代替迈克耳孙干涉仪中的分束镜和补偿板，不仅消除了杂散光斑，且简化了仪器的结构．     

锥体棱镜的加工

本文简单地叙述了锥体棱镜两种加工工艺。重点介绍直接成型法加工中对角度误差~1″的控制。并提出了角度超差零件返修时的光胶方法。