Hyperparameter on-line learning of stochastic resonance based threshold networks

Aiming at training the feed-forward threshold neural network consisting of nondifferentiable activation functions, the approach of noise injection forms a stochastic resonance based threshold network that can be optimized by various gradient-based optimizers. The introduction of injected noise extends the noise level into the parameter space of the designed threshold network, but leads to a highly non-convex optimization landscape of the loss function. Thus, the hyperparameter on-line learning procedure with respective to network weights and noise levels becomes of challenge. It is shown that the Adam optimizer, as an adaptive variant of stochastic gradient descent, manifests its superior learning ability in training the stochastic resonance based threshold network effectively. Experimental results demonstrate the significant improvement of performance of the designed threshold network trained by the Adam optimizer for function approximation and image classification.     

Optimization of Transducer Location for Novel Non-Intrusive Methodologies of Diagnosis in Diesel Engines

The health monitoring has been studied to ensure integrity of design of engine structure by detection, quantification, and prediction of damages. Early detection of faults may allow the downtime of maintenance to be rescheduled, thus preventing sudden shutdown of machines. In cylinder pressure developed, vibrations and noise emissions data provide a rich source of information about condition of engines. Monitoring of vibrations and noise emissions are novel non-intrusive methodologies for which positioning of various transducers are important issue. The presented work shows applicability of these diagnosis methodologies adopted in case of diesel engines. The effects of changing various fuel injection parameters was analyzed. Scope of using non-intrusive technique has been analyzed by changing locations of microphone. Novelty of this worklies in exploring signal processing methods for various locations around the engine test set up. Various frequency ranges of contributing noise and vibration sources were identified. Time-Frequency analysis showed the onset of various cyclic. Based on the identification of various frequency bands, it is possible to device suitable filters in order to extract more information.     

2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

Assessment of Noise Exposure of Sawmill Workers in Southwest,Nigeria

Economic wood processing employs the use of industrial machines for cutting, shaping, milling, and sawing timber, thereby leading to the generation of high levels of noise. Published data from empirical studies have categorized noise as an environmental hazard of global significance. Furthermore, noise exposure limits for different industries and all the industrial machines available has not been formally established as it presently exists in developed nations around the world. Therefore, this study assessed the daily exposure of sawmills workers to noise in Southwestern Nigeria. Reconnaissance surveys were first carried out in Osun, Oyo, Ondo, Ekiti, Lagos, and Ogun States to select sawmills that were fully operational and fit for the study. Two fully functional sawmills in two cities of each State were eventually selected for data collection, making a total of 24 sawmills, while the Circular Machines (CM), Planer Machines (PM), and Band-saw Machines (BM) were the machines in each sawmill considered. Two machines each of CM, PM, and BM were considered in each sawmill, making a total of forty-eight (48) machines each of CM, PM, and BM. Sound data were collected between 7 am and 7 pm each day for six days (between Monday and Saturday) using Extech 407732 sound level meter and all stabilized measurements were taken three times at different intervals. The data collected were in three different periods: Machine No-work Period (NP_m), Machine Idle Period (IP_m), and Machine Working Period (WP_m). A two–way Analysis of Variance (ANOVA) was carried out at P < 0.05 to determine whether there is a significant difference in the sound level average before and after the break, for both the idle and working periods of the three machines considered. This was also done to determine whether there is a significant difference between the sound level average of the results collected during idle and working periods of the three machines. Noise Pollution Levels (L_np) ranged from 83.20 dB (PM) to 107.65 (BM) and 93.42 (CM and PM) – 116.00 (BM) respectively, while IP_m also gave the least noise pollution level of 95.79 dB and WP_m gave the highest level of 102.88 dB. The results revealed that all the machines’ L_np values in the working period are more than the 90 dB acceptable limit the recommendation value of 90 dB while 89.6% of CMs, 75% of PMs, and 89.6% of BM had their L_np above 90 dB in the idle period respectively. The minimum and the maximum noise dose levels for IP_m, WP_m and overall are 0.09 (BM) and 2.37 (CM), 0.50 (CM), and 4.77 (PM) and 0.69 (BM) and 6.64 (PM) respectively. The study found out that the fundamental contributing factors to the high noise levels in sawmills are poor machine maintenance, use of old and obsolete machines, poor housekeeping strategy, limited space, workers’ negligence, lack of PPE, and lack of occupational safety training. The study recommends that proper workplace practices such as use of personal protective equipment, new and modern machines, training, and occupational safety programmes be implemented in the considered sawmills.     

Full counting statistics of transport electrons through a two-level quantum dot with spin–orbit coupling

We study the full counting statistics of transport electrons through a semiconductor two-level quantum dot with Rashba spin–orbit (SO) coupling, which acts as a nonabelian gauge field and thus induces the electron transition between two levels along with the spin flip. By means of the quantum master equation approach, shot noise and skewness are obtained at finite temperature with two-body Coulomb interaction. We particularly demonstrate the crucial effect of SO coupling on the super-Poissonian fluctuation of transport electrons, in terms of which the SO coupling can be probed by the zero-frequency cumulants. While the charge currents are not sensitive to the SO coupling.     

Liquid Marble Patchwork on Super-Repellent Surface

Liquid marble (LM) is a droplet that is wrapped by hydrophobic solid particles, which behave as a non-wetting soft solid. Based on these properties, LM can be applied in fluidics and soft device applications. A wide variety of functional particles have been synthesized to form functional LMs. However, the formation of multifunctional LMs by integrating several types of functional particles is challenging. Here, a general strategy for the flexible patterning of functional particles on droplet surfaces in a patchwork-like design is reported. It is shown that LMs can switch their macroscopic behavior between a stable and active state on super-repellent surfaces in situ by jamming/unjamming the surface particles. Active LMs hydrostatically coalesce to form a self-sorted particle pattern on the droplet surface. With the support of LM handling robotics, on-demand cyclic activation–manipulation–coalescence–stabilization protocols by LMs with different sizes and particle types result in the reliable design of multi-faced LMs. Based on this concept, a single bi-functional LM is designed from two mono-functional LMs as an advanced droplet carrier.     

一款紧凑增强型可变阻抗电磁带隙结构

基于传统AI-EBG结构,提出了一种小尺寸的增强型电磁带隙结构,实现了从0.5~9.4 GHz的宽频带-40 dB噪声抑制深度,且下截止频率减少到数百MHz,可有效抑制多层PCB板间地弹噪声。文中同时研究了EBG结构在高速电路应用时的信号完整性问题,使用差分信号方案可改善信号完整性。     

面源红外诱饵对抗红外制导导弹干扰策略研究

面源红外诱饵使用的过程中,合理有效的干扰策略是干扰红外制导导弹的关键,针对这一问题,通过理论分析与仿真模拟相结合得到面源红外诱饵对抗红外制导导弹的干扰策略。首先以红外成像制导导弹为例,介绍红外制导导弹的仿真模型,然后将攻击过程分为锁定前与锁定后,以命中率为评价指标,得到两个阶段下的最佳干扰策略,包括诱饵的最佳释放时机、释放间隔以及载机应采取的机动动作等。     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.     

磁场天线的扭转振动及运动感应噪声研究

拖曳天线的运动感应电磁噪声对其收信深度及接收性能占据主导作用,其中横向振动与纵向振动是主要的,同时扭转振动也不可忽略.建立了磁场天线的扭转振动模型,得到了流体圆周切变力作用下磁场天线的扭转振动响应,分析了扭转振动感应电磁噪声的产生机理,给出了计算公式及仿真结果.研究结果为水下电磁噪声的深入研究提供了理论基础.