Statistical Piezotronic Effect in Nanocrystal Bulk by Anisotropic Geometry Control

Utilizing inner-crystal piezoelectric polarization charges to control carrier transport across a metal-semiconductor or semiconductor–semiconductor interface, piezotronic effect has great potential applications in smart micro/nano-electromechanical system (MEMS/NEMS), human-machine interfacing, and nanorobotics. However, current research on piezotronics has mainly focused on systems with only one or rather limited interfaces. Here, the statistical piezotronic effect is reported in ZnO bulk composited of nanoplatelets, of which the strain/stress-induced piezo-potential at the crystals’ interfaces can effectively gate the electrical transport of ZnO bulk. It is a statistical phenomenon of piezotronic modification of large numbers of interfaces, and the crystal orientation of inner ZnO nanoplatelets strongly influence the transport property of ZnO bulk. With optimum preferred orientation of ZnO nanoplatelets, the bulk exhibits an increased conductivity with decreasing stress at a high pressure range of 200–400 MPa, which has not been observed previously in bulk. A maximum sensitivity of 1.149 µS m⁻¹ MPa⁻¹ and a corresponding gauge factor of 467–589 have been achieved. As a statistical phenomenon of many piezotronic interfaces modulation, the proposed statistical piezotronic effect extends the connotation of piezotronics and promotes its practical applications in intelligent sensing.     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

铝薄膜CMP影响因素分析

提出了在碱性抛光液中铝薄膜化学机械抛光的机理模型,对抛光液的pH值、磨料、氧化剂浓度对过程参数的影响做了一些试验分析。试验结果表面粗糙度的铝薄膜所需的最优化CMP过程参数:硅溶胶粒径为15～20nm,pH值为10.8～11.2,氧化剂浓度为2.5%～3%。     

Characterization and optimization of copper chemical mechanical planarization

The feature scale planarization of the copper chemical mechanical planarization (CMP) process has been characterized for two copper processes using Hitachi 430-TU/Hitachi T605 and Cabot 5001/Arch Cu10K consumables. The first process is an example of an abrasive-free polish with a high-selectivity barrier slurry, while the second is an example of a conventional abrasive slurry with a low-selectivity barrier slurry. Copper fill planarization has been characterized for structures with conformal deposition as well as with bumps resulting from bottom-up fill. Dishing and erosion were characterized for several structures after clearing. The abrasive-free polish resulted in low sensitivity to overpolish and low saturation levels for dishing and erosion. Consequently, this demonstrated superior performance when compared to the International Technology Roadmap for Semiconductors (ITRS) 2000 roadmap targets for planarization. While the conventional slurry could achieve the 0.13-μm technology node requirements, the abrasive-free polish met the planarization requirements beyond the 0.10-μm technology node.     

93W合金有关力学参量的综合选评

 对93W合金材料进行了超声测量实验，并结合原有的超声测量结果进行了分析比较，提出了可以直接用冲击波速度关系式的三个系数c₀ 、λ和λ′来对钨合金的有关力学参量，如G₀、K₀、G₀′、K₀′等进行综合选评的方法。得到了一组对93W合金较为合理的力学参量推荐值。     

复合体系方法测量液体力学谱

本文介绍了采用复合体系，测量得到凝聚态物质从固态到液态连续变化力学谱的一种新的实验方法。以簧振动为例，给出了解析的计算公式，以及应用条件。通过进一步综合分析，得到具有更广应用范围的近似公式，可以近似应用于其他不同的振动模式，如低频扭摆。应用新的测量方法，给出了典型小分子玻璃材料甘油和碳酸丙稀从玻璃态到液态的力学谱，观察到甘油和碳酸丙稀玻璃化转变、碳酸丙稀的再结晶、熔化和挥发的过程；测量得到挥发过程中水的质量随时间精确变化的曲线。最后，本文给出了新方法的一些应用展望。     

NiTi形状记忆薄膜的显微结构和力学性能

NiTi形状记忆合金薄膜具有形状记忆效应，极有希望用于制造高技术领域微电子机械系统中的微型激发器。NiTi形状记忆合金薄膜在制备和使用过程中需要高品质（衬）底材。本文利用高分辨电子显微学和高分辨分析电子显微学详细研究了硅底材NiTi形状记忆合金薄膜的NiTi／Si和NiTi／SiO2微结构体系，包括薄膜精细结构和界面反应。也研究了其显微结构和力学性能的关系。特别给出了NiTi形状记忆合金薄膜产生疲劳过程的微观过程的起因，通过高达十万个使用热循环前后样品显微结构变化的比较，发现纳米尺度上的TiNi3新相的形成导致疲劳过程的发生。如何抑制TiNi3新相形成的研究正在进行之中，这将为进一步提高NiTi形状记忆合金的使用寿命指出方向。     

Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

用于机械振动实时监测的光纤光栅有源传感装置

把一对中心反射波长分别为1562.11nm和1562.71nm的光纤光栅粘贴在均质、等厚、等腰三角形悬臂梁上下表面作为环形腔光纤激光器端镜，当机械振动激励自由端时，通过观测激光输出脉冲，地施加于自由端的机械振动的频率进行了实时监测；观察两光栅波长漂移量差值的变化，可在0～6.1mm的范围内判断所测振动的振幅。低于100Hz时，实验结果与实际值基本吻合。     

Effect of short glass fiber on structure and viscoelastic behavior of olefinic polymers synthesized with metallocene catalyst

Several composites were prepared on the basis of an ethylene homopolymer and different copolymers of ethylene and 1‐hexene, synthesized with a metallocene catalyst, as matrices and a content of a 5 wt % of short glass fiber. The effect of the fiber incorporation on the structure and mechanical and viscoelastic behaviors was analyzed for the different samples. The glass fibers induced a slightly higher crystallinity, and the crystallite morphology significantly changed (long spacings and crystal orientation). The incorporation of fibers did not reinforce the different matrices under study at this low content; consequently, the mechanical parameters, such as Young's modulus, yielding stress, and microhardness, were lower in the composites as compared with those values found in the neat polyolefins. The location and apparent activation energies of distinct relaxation processes are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1244–1255, 2003