基于新型光纤的传输技术探讨

随着互联网的高速发展，引发了网络流量、电信骨干网流量急速增长，使得网络容量的提升迫在眉睫。目前，100G 系统已经商用，超100G系统能够更有效地解决流量和网络带宽持续增长带来的压力，本文主要介绍新型单模光纤的特性以及探讨基于新型单模光纤的传输技术。     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Voltage reference architectures for low-supply-voltage low-power applications

This paper presents a voltage reference generator architecture and two different realizations of it that have been fabricated within a standard 0.18 μm CMOS technology. The architecture takes the advantage of utilizing a sampled-data amplifier (SDA) to optimize the power consumption. The circuits achieve output voltages on the order of 190 mV with temperature coefficients of 43 ppm/°C and 52.5 ppm/°C over the temperature range of 0 to 120°C without any trimming with a 0.8 V single supply. The power consumptions of the circuits are less then 500 nW while occupying an area of 0.2 mm² and 0.08 mm², respectively.     

氮化硅/石墨激光合金化涂层的组织结构与性能研究

为获得金属表面特别是高副接触金属表面含自润滑特性且具有高硬度耐磨特性的功能材料 ,研究了 45 # 钢表面激光合金化氮化硅 /石墨复合涂层的工艺方法、组织特征、界面形态及其形成机制 ,利用光学显微镜、扫描电镜和X射线能谱对所形成合金化层的元素分布和含量进行了分析 ,并对试样硬度进行了测定。结果表明 ,合金化层中元素Fe ,Co ,Si,C分布均匀 ;C含量达到了 15 6 9%,大部分以石墨的形式存在 ,具有一定的自润滑性能 ;但在形成合金化层的温度条件下 ,氮化硅分解严重 ;合金化层硬度提高的主要原因是Si Fe ,Co Fe固溶体的强化作用及高碳马氏体的生成和高硬度碳化物的存在。     

微流控分析芯片制作中的低温键合技术

微流控分析芯片制作方法的研究是微流控分析的基础。制作性能良好的微流控分析芯片时,基片与盖片的键合技术十分重要。本文针对近年来发展迅速的低温键合技术,对各种方法进行了评价,并对其发展前景进行了展望。     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

Spray Freeze-drying – The Process of Choice for Low Water Soluble Drugs?

Most of the novel highly potent drugs, developed on the basis of modern molecular medicine, taking into account cell surface recognition techniques, show poor water solubility. A chemical modification of the drug substance enhancing the solubility often decreases the pharmacological activity. Thus, as an alternative an increase of the solubility can be obtained by the reduction of the size of the drug particles. Unfortunately, it is often difficult to obtain micro or nanosized drug particles by classical or more advanced crystallization using supercritical gases or by milling techniques. In addition, nanosized particles are often not physically stable and need to be stabilized in an appropriate matrix. Thus, it may be of interest to manufacture directly nanosized drug particles stabilized in an inert hydrophilic matrix, i.e. nanostructured and nanocomposite systems. Solid solutions and solid dispersions represent nanostructured and nanocomposite systems. In this context, the use of the vacuum-fluidized-bed technique for the spray-drying of a low water soluble drug cosolubilized with a hydrophilic excipient in a polar organic solvent is discussed. In order to avoid the use of organic solvents, a special spray-freeze-drying technique working at atmospheric pressure is presented. This process is very suitable for temperature and otherwise sensitive drugs such as pharmaproteins.     

32位MIPS微处理器中乘法器的设计和实现

在Booth算法的基础上,结合MIPS 4KC微处理器中的流水线结构和乘法器的工作过程,提出了一种改进的Booth乘法器的设计方法,并采用全制定方法实现,用这种方法实现的乘法器单元具有面积小、单元电路可重复性好、版图设计工作量小、功耗低等特点.     

BEPCII直线加速器相控系统设计研究

为了补偿由于各种因素引起的微波相位漂移,BEPCII直线加速器需要建立微波相位反馈控制系统.能量最大法将用来确定每台功率源的最佳相位.沿直线加速器速调管长廊铺设相位稳定同轴线提供相位参考.现在已经完成了关键部件,如PAD单元、IfA 单元的开发.搭建了相控最小系统对系统进行了验证.     

Robust Speed Control of a Low Damped Electromechanical System Based on CRONE Control: Application to a Four Mass Experimental Test Bench

Robust speed control of a low damped electromechanical system with backlash is studied, controlled load angular speed being not measured. The proposed control strategy combines a Luenberger observer (load angular speed and load torque disturbance estimations) and a robust CRONE controller. The observer provides estimation of the load angular speed and of the disturbance torque applied on the load. Through the computation of only three independent parameters (as many as a PID controller), the CRONE controller permits to ensure the robust speed control of the load in spite of plant parametric variations and speed observation errors. The proposed control strategy is applied to a four mass experimental test bench.