Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

从PZT体系看无铅压电陶瓷的可能应用

总结了主要以(Bi0.5Na0.5)TiO3和NaNbO3为基的无铅压电陶瓷的性能，以Pb(Ti，Zr)TiO3基二元系、三元系压电陶瓷的性能与应用为参考，分析了无铅压电陶瓷可能的器件应用。此外，还对拓宽无铅压电陶瓷应用需要改进的性能提出了建议。     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

Interfacial reactions in In-Sn/Ni couples and phase equilibria of the In-Sn-Ni system

The In-Sn-Ni alloys of various compositions were prepared and annealed at 160°C and 240°C. No ternary compounds were found; however, most of the binary compounds had extensive ternary solubility. There was a continuous solid solution between the Ni₃Sn phase and Ni₃In phase. The Sn-In/Ni couples, made of Sn-In alloys with various compositions, were reacted at 160°C and 240°C and formed only one compound for all the Sn-In alloys/Ni couples reacted up to 8 h. At 240°C, Ni₂₈In₇₂ phase formed in the couples made with pure indium, In-10at.%Sn and In-11at.%Sn alloys, while Ni₃Sn₄ phase formed in the couples made of alloys with compositions varied from pure Sn to In-12at.%Sn. At 160°C, except in the In/Ni couple, Ni₃Sn₄ formed by interfacial reaction.     

Non-isothermal short-range-order kinetics of binary alloys as influenced by solute-vacancy complexes

A model describing the roles of bound and unbound vacancies is proposed in order to predict defect decay and short-range-order kinetics of quenched binary alloys during linear heating experiments. This is an alternative treatment of a previous approach. The model has been applied to the differential scanning calorimetry (DSC) curves of Cu-5 at.% Zn quenched from different temperatures. An expression to calculate the activation energy for migration of solute-vacancy complexes was also developed which make use of DSC trace data. A value of 89.12±0.32 kJ mol^-1 was obtained for the above alloy. The relative contribution of bound and unbound vacancies to partition of effective activation energy corresponding to the ordering process as influenced by quenching temperature was also assessed. This revised version was published online in July 2006 with corrections to the Cover Date.     

快冷Fe_(71)Al_(29)合金中的两个内耗峰

用一个计算机控制的倒扭摆研究了快冷Fe71 Al2 9合金中的两个内耗峰 .在快冷的Fe71 Al2 9样品中分别在 180℃(P1 ) ,340℃ (P2 )和 5 10℃ (P3)出现了内耗峰 ,而在慢冷的Fe71 Al2 9样品中只发现了P3峰 .快冷样品中的P1 和P2峰在从 6 5 0℃冷却下来的测量过程中或在 35 0℃经过较长时间的时效后消失 ,其峰高随时效时间的增加而下降 ,直至消失 .P1 和P2 峰都有弛豫特征 ,它们的激活能分别为 :H1 =1.0 3± 0 .0 8eV(P1 峰 ) ;H2 =1.6 4± 0 .0 5eV(P2 峰 ) .P1 峰被认为是无序合金中Al原子在四面体点阵内的最近邻运动所引起 ,P2 峰则是无序合金中Al原子在四面体点阵内的次近邻运动所引起     

印制板液态感光阻焊油墨的工艺控制

本文介绍印制板液态感光阻焊油墨的工艺流程、工艺控制，并对生产中较常出现的几种质量问题进行讨论，进而提出解决措施。     

Al—Si—Mn—Fe合金中相组成的电子衍射鉴定

本文利用选区电子衍射,并结合X射线衍射对六种不同成份的急冷合金及其退火后的相组成进行了鉴定,得到了它们的相组成。     

Mossbauer investigations of corrosion environment influence on Fe valence states in oxide films of zirconium alloys

Mössbauer investigations about iron atom redistribution in oxide films of zirconium alloys subjected to corrosion at 500°C in pure oxygen and water pair have been analysed. The alloys were also subjected to autoclave conditions at a pressure of 10.0 MPa and autoclave conditions at 350°C and at a pressure of 16.8 MPa, using distilled water and water with additives of lithium and fluorine. It is shown that, depending on the corrosion environment, various compounds of iron, such as α-Fe₂O₃, Fe₃O₄, and FeO, as solid solutions of iron in ZrO₂ are formed in oxide films.