氧化锶催化性质：Ⅱ.SrO,MgO上异丙醇的分解反应

ＳｒＯ，ＭｓＯ对异丙醇的分解反应有各自的作用形式，因而产物分布也有明显差别．ＭｇＯ上异丙醇分解，在较低温度时，主要产物为丙酮和丙烯；随温度升高，生成丙烯的量增加，而丙酮的量减少，直至消失，在ＳｒＯ上，异丙醇在较高温度时反应，产物几乎为丙酮，丙烯的生成量极少。认为：产物中丙烯来源于异丙醇在催化剂表面强酸中心上的脱水；丙酮在ＭｇＯ上来源于强碱中心和酸中心协同作用异丙醇的脱氢，而在ＳｒＯ上则是ＳｒＯ表面极强的碱中心作用异丙醇而脱氢制得。     

Pt/HL和Pt/KL沸石在异丙醇分解反应中的不同催化行为

Ｐｔ／ＫＬ沸石在异丙醇分解反应中具有很高的脱氢活性,而Ｐｔ／ＨＬ沸石具有明显的缺电子性,在此反应中难以显示出脱氢活性,通过加氢作用,可使沸石的酸位免受积炭覆盖,从而可增强Ｐｔ／ＨＬ沸石的酸性催化作用。     

探针反应和FTIR法研究Pt与L型沸石的相互作用

探针反应和ＦＴＩＲ法研究Ｐｔ与Ｌ型沸石的相互作用董家禄,朱建华,须沁华,张婕,刘大壮（南京大学化学系,南京,２１０００８）（郑州工学院化工系,郑州,４５０００２）关键词Ｐｔ／Ｌ沸石,沸石催化剂,异丙醇分解反应,Ｐｔ－载体相互作用Ｐｔ的分散度和电子状态...     

以水滑石及类水滑石为前体的Mg/Al、Co/Al及Co/Mg/Al混合氧化物的合成、表征和异丙醇催化性能

以共沉淀法合成的水滑石(HT)和类水滑石(HTLc)为前体制备了镁铝、钴铝、钴镁铝混合氧化物，采用了BET、XRD、TG-DTA、TPR、FTIR和微量量热吸附及异丙醇催化反应进行了研究。结果表明：以HT和HTLc为前体制备的混合氧化物，其比表面积较大、并随着钴含量的增加而降低。在HT中引入Co²⁺离子后，由于Co²⁺离子的氧化还原属性，削弱了水滑石层对阴离子的键合能力，从而使其热分解温度及热稳定性降低，导至焙烧后生成的混合氧化物的比表面积比不含钴的2Mg/Al混合氧化物的低。在TPR过程中，镁铝混合氧化物不被还原，而含钴的混合氧化物的还原是经由Co³⁺ → Co²⁺ → Co⁰的过程。混合氧化物表面含有酸性位和碱性位，并随着钴含量的变化而得到调变。含钴氧化物样品的表面以L酸为主和含有很少量的B酸。异丙醇催化反应生成丙酮的选择性最高，表明样品表面的氧化还原位是主要的，随着钴的加入及含量的增大，异丙醇催化反应的转化率也是增大的。     

Flexible strain sensor with ridge-like microstructures for wearable applications

The flexible stretchable sensors have great potential for implementation in various applications, such as intelligent soft robots, health monitoring, and motion detection. However, most of the flexible stretchable sensors with microstructures and high sensitivities are fabricated by expensive templates and complex processes. In consideration of large-scale fabrication, a low cost and efficient way is in great demand. Herein, electroless plating on Nafion films with decent swelling ratios are proposed to fabricate stretchable sensors with wrinkle-structured electrodes. By adding isopropanol (IPA) to the electroless plating process, the H₂O-IPA sensor with larger swelling ratio shows deeper surface wrinkles, higher surface roughness, and better sensitivity to strain. At the same time, the H₂O-IPA sensor exhibit good durability (500 cycles). By mounting the sensor on the joint of human finger, the motion of the finger bending and even the bending degree can be accurately detected, indicating the potential use in the field of wearable devices and soft electronic skins.     

MgO在NaY沸石上的分散及其催化性能

采用微波辐射方法将ＭｇＯ直接分解在ＮａＹ沸石上,从而获得强碱性活性位。ＭｇＯ／ＮａＹ具有耐水冲刷性,克服了通常负载型固体碱在水中易流失的弱点,并在２７３Ｋ的顺式－２－丁烯异构化反应中具有催化活性。     

SiO2-Al2O3玻纤载体负载CuO-CeO2对挥发性有机化合物催化燃烧性能研究

采用等体积共浸渍法制备了CuO-CeO₂整体式催化剂,评价了催化剂对乙酸乙酯、异丙醇及甲苯的催化燃烧性能。采用N₂吸附-脱附、X射线衍射（XRD）、氢气程序升温还原（H₂-TPR）、氨气程序升温脱附（NH₃-TPD）以及挥发性有机化合物脱附等手段对催化剂进行了表征。表征数据显示,氧化铜以高分散态均匀分散存在于载体表面,氧化铈则是小的纳米颗粒,氧化铈颗粒粒径随着Cu/Ce物质的量比的减小而增大。添加铈氧化物会显著增加总酸量,特别是路易斯酸酸位的量,同时增强了乙酸乙酯和异丙醇的吸附量,吸附量的增加提高了催化剂对乙酸乙酯和异丙醇的催化燃烧性能。从甲苯的催化燃烧实验可以看出,大量添加CeO₂稍微增加了甲苯的吸附容量,减弱了催化剂的还原性、降低了活性氧的含量,最终导致甲苯的低转化率。催化行为由氧化铜、氧化铈以及载体三者之间的共同作用决定,这三者的协同作用不仅影响着表面氧的活性同时影响着催化剂对甲苯的吸附能力。     

Polyamide-imide/polyetherimide dual-layer hollow fiber membranes for pervaporation dehydration of C1–C4 alcohols

To circumvent the common swelling and deteriorated performance of integral asymmetric hollow fiber membranes for pervaporation dehydration, we have developed novel polyamide-imide (PAI)/polyetherimide (PEI) hollow fiber membranes with synergized performance with the aid of dual-layer spinning technology. Dehydration of C1–C4 alcohols has been conducted and the orders of their fluxes and permeances have been analyzed. The hollow fibers spun at 2 cm air gap and annealed at 75 °C exhibit the highest pervaporation performance: separation factors for t-butanol/water and iso-butanol/water binary systems are greater than 50,000 with flux more than 700 g/m² h. A comparison with literature data shows that the newly developed membranes outperform most other polymeric membranes for the dehydration of IPA and butanols. The dual-layer hollow fiber membranes also exhibit good long-term stability up to 200 h. The superior performance can be attributed to (1) the balanced properties of PAI as the selective layer for dehydration pervaporation; (2) the low water uptake and less swelling characteristic of the PEI supporting layer; and (3) the desirable membrane morphology consisting of a fully porous inner layer, a porous interface, and an ultrathin dense-selective outer skin.     

锌硅钼钨多元取代多金属含氧簇合物的合成、表征及其催化异丙醇气相反应的活性

利用pH值的调变, 以H₄SiMo_12－nW_nO₄₀•(20～25)H₂O (n＝2, 4, 6, 8, 10)和Zn(NO₃)₂饱和溶液为原料制得一系列锌硅钼钨多元取代多金属含氧簇合物, 通过IR, XRD, XPS等方法对合成的催化剂的结构和性质进行了表征, 并利用吡啶吸附红外及氨程序升温脱附分别测定样品表面的酸种类和酸强度. 考察了催化剂对异丙醇气相反应的活性, 同时详细研究了异丙醇气相反应产物分布与催化剂组成之间的关系.