靶面激光光斑尺寸原位测量的研究

提供了一种简便易行的靶面激光光斑尺寸原位测量的方法。从高斯光束的横向光强分布特性出发,建立了激光烧蚀斑半径与辐照激光能量、光斑尺寸、烧蚀阈值间的关系式,模拟分析发现辐照激光光斑尺寸对烧蚀斑半径随辐照能量变化曲线有较大影响。对于脉宽为2 ms,波长为1064 nm的激光,实验测量了不同能量激光辐照下相纸烧蚀斑半径,并用推导出的关系式拟合测量数据,获得了靶面处光斑尺寸和样品烧蚀阈值。同时,也测量了不同位置处的光斑尺寸和样品烧蚀阈值,对高斯光束束腰位置和样品烧蚀阈值的光斑尺寸效应进行了验证。研究结果表明该技术结果可靠,简单高效。该技术可以为高能激光与固体物质相互作用的基础研究和激光加工等应用领域中实现简单方便地测量靶面光斑尺寸提供帮助。     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Enhancement of optical and electrical properties of SILAR deposited ZnO thin films through fluorine doping and vacuum annealing for photovoltaic applications

Undoped and fluorine doped ZnO thin films were deposited onto glass substrates using successive ionic layer adsorption and reaction (SILAR) technique and then annealed at 350 °C in vacuum ambience. The F doping level was varied from 0 to 15 at% in steps of 5 at%. The XRD analysis showed that all the films are polycrystalline with hexagonal wurtzite structure and preferentially oriented along the (002) plane. Crystallite sizes were found to increase when 5 at% of F is doped and then decreased with further doping. It was seen from the SEM images that the doping causes remarkable changes in the surface morphology and the annealing treatment results in well-defined grains with an improvement in the grain size irrespective of doping level. All the films exhibit good transparency (>70%) after vacuum annealing. Electrical resistivity of the film was found to be minimum (1.32×10⁻³ Ω cm) when the fluorine doping level was 5 at%.     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

RF磁控溅射制备钛酸锶钡BST纳米薄膜

钛酸锶钡(BST)薄膜作为一种高K介质材料在微电子和微机电系统等领域具有广阔的应用前景,人们已对BST薄膜的制备工艺技术和介电性能进行了大量的研究。BST纳米薄膜的制备工艺直接影响和决定着薄膜的介电性能(介电常数、漏电流密度、介电强度等)。对RF磁控反应溅射制备BST纳米薄膜的工艺技术进行了综述。从溅射靶的制备、溅射工艺参数的优化、热处理、薄膜组分的控制,及制备工艺对介电性能的影响等方面,对现有研究成果进行了较全面的总结。     

A Bluetooth Based Sensor Network for Civil Infrastructure Health Monitoring

Communicating with sensors has long been limited either to wired connections or to proprietary wireless communication protocols. Using a ubiquitous and inexpensive wireless communication technology to create Sensor Area Networks (SANs) will accelerate the extensive deployment of sensor technology. Bluetooth, an emerging, worldwide standard for inexpensive, local wireless communication is a viable choice for SANs because of its inherent support for some of the important requirements – low power, small form factor, low cost and sufficient communication range. In this paper we outline an approach, centered on the Bluetooth technology, to support a sensor network composed of fixed wireless sensors for health monitoring of highways, bridges and other civil infrastructures. We present a topology formation scheme that not only takes into account the traffic generated by different sensors but also the associated link strengths, buffer capacities and energy availability. The algorithm makes no particular assumptions as to the placement of nodes, and not all nodes need to be in radio proximity of each other. The output is a tree shaped scatternet rooted at the sensor hub (data logger) that is balanced in terms of traffic carried on each of the links. We also analyze the scheduling, routing and healing aspects of the resulting sensor-net topology.     

Quantum states in fabricating poly-Si films

The quantum states are presented in these processions of fabricating poly-Si films. Amorphous silicon films prepared by PECVD has been crystallized by conventional furnace annealing (FA) and rapid thermal annealing (RTA), respectively. It is found that the thin films grain size present quantum states with the increasing of the gas flow ratios of SiH₄, H₂ mixture, substrate temperatures, frequency power, annealing temperature and time.     

Stochastic techniques for global optimization: A survey of recent advances

In this paper stochastic algorithms for global optimization are reviewed. After a brief introduction on random-search techniques, a more detailed analysis is carried out on the application of simulated annealing to continuous global optimization. The aim of such an analysis is mainly that of presenting recent papers on the subject, which have received only scarce attention in the most recent published surveys. Finally a very brief presentation of clustering techniques is given.     

Simulated annealing with noisy or imprecise energy measurements

The annealing algorithm (Ref. 1) is modified to allow for noisy or imprecise measurements of the energy cost function. This is important when the energy cannot be measured exactly or when it is computationally expensive to do so. Under suitable conditions on the noise/imprecision, it is shown that the modified algorithm exhibits the same convergence in probability to the globally minimum energy states as the annealing algorithm (Ref. 2). Since the annealing algorithm will typically enter and exit the minimum energy states infinitely often with probability one, the minimum energy state visited by the annealing algorithm is usually tracked. The effect of using noisy or imprecise energy measurements on tracking the minimum energy state visited by the modified algorithms is examined.The research reported here has been supported under Contracts AFOSR-85-0227, DAAG-29-84-K-0005, and DAAL-03-86-K-0171 and a Purdue Research Initiation Grant.     

a-C:F薄膜的热稳定性与光学带隙的关联

以CF4和C6H6的混合气体作为气源,在微波电子回旋共振化学气相沉积(ECRCVD)装置中制备了氟化非晶碳薄膜(aC:F),并在N2气氛中作了退火处理以考察其热稳定性.通过傅里叶变换红外吸收谱和紫外可见光谱获得了薄膜中CC双键的相对含量和光学带隙,发现膜中CC键含量与光学带隙之间存在着密切的关联,在高微波功率下沉积的氟化非晶碳膜具有低的光学带隙和较好的热稳定性. 关键词： 氟化非晶碳膜 光学带隙 退火温度 热稳定性