靶面激光光斑尺寸原位测量的研究

提供了一种简便易行的靶面激光光斑尺寸原位测量的方法。从高斯光束的横向光强分布特性出发,建立了激光烧蚀斑半径与辐照激光能量、光斑尺寸、烧蚀阈值间的关系式,模拟分析发现辐照激光光斑尺寸对烧蚀斑半径随辐照能量变化曲线有较大影响。对于脉宽为2 ms,波长为1064 nm的激光,实验测量了不同能量激光辐照下相纸烧蚀斑半径,并用推导出的关系式拟合测量数据,获得了靶面处光斑尺寸和样品烧蚀阈值。同时,也测量了不同位置处的光斑尺寸和样品烧蚀阈值,对高斯光束束腰位置和样品烧蚀阈值的光斑尺寸效应进行了验证。研究结果表明该技术结果可靠,简单高效。该技术可以为高能激光与固体物质相互作用的基础研究和激光加工等应用领域中实现简单方便地测量靶面光斑尺寸提供帮助。     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

Microstructural stability and age-hardening behavior of Re-added dual two-phase Ni3Al and Ni3V intermetallic alloys

The effect of Re addition on the microstructure and hardening behaviour of the dual two-phase Ni₃Al (L1₂) and Ni₃V (D0₂₂) intermetallic alloy was investigated by scanning electron microscopy, transmission electron microscopy and Vickers hardness test. The two-phase eutectoid microstructure accompanying the Re-rich precipitates were observed in the channel region of the alloys in which Re substituted for Ni but not in those in which Re substituted for Al and V. The concomitant addition of Nb (or Ta) with Re more stabilized the two-phase eutectoid microstructure and consequently more induced the fine precipitates in the channel region. The annealing at temperatures below the eutectoid temperature was necessary to induce the fine precipitates in the channel region and thereby result in the precipitation hardening. The fine precipitation in the channel region and related hardening was attributed to the alloying feature so that Re is soluble in the A1 (fcc) phase at high temperatures and becomes less soluble in the two intermetallic phases decomposed from the A1 phase at low temperatures.     

Experimental and Theoretical Mechanistic Study on the Thermal Decomposition of 3,3-diphenyl-4-(trichloromethyl)-5-nitropyrazoline

The present paper is a continuation of comprehensive study regarding to synthesis and properties of pyrazoles and their derivatives. In its framework an experimental and theoretical studies of thermal decomposition of the 3,3-diphenyl-4-(trichloromethyl)-5-nitropyrazoline were performed. It was found, that the decompositions of the mentioned pyrazoline system in the solution and at the melted state proceed via completely different molecular mechanisms. These mechanisms have been explained in the framework of the Molecular Electron Density Theory (MEDT) with the computational level of B3LYP/6-31G(d). A Bonding Evolution Theory (BET) examination of dehydrochlorination of the 3,3-diphenyl-4-(trichloromethyl)-5-nitropyrazoline permits elucidation of the molecular mechanism. It was found, that on the contrary for most known HCl extrusion processes in solution, this reaction is realised via single-step mechanism.     

Theory of chemical bonds in metalloenzymes XXII: a concerted bond-switching mechanism for the oxygen–oxygen bond formation coupled with one electron transfer for water oxidation in the oxygen-evolving complex of photosystem II

ABSTRACT

QM(UB3LYP)/MM(AMBER) calculations were performed for the locations of the transition structure (TS) of the oxygen–oxygen (O–O) bond formation in the S₄ state of the oxygen-evolving complex (OEC) of photosystem II (PSII). The natural orbital (NO) analysis of the broken-symmetry (BS) solutions was also performed to elucidate the nature of the chemical bonds at TS on the basis of several chemical indices defined by the occupation numbers of NO. The computational results revealed a concerted bond switching (CBS) mechanism for the oxygen–oxygen bond formation coupled with the one-electron transfer (OET) for water oxidation in OEC of PSII. The orbital interaction between the σ-HOMO of the Mn(IV)₄–O₍₅₎ bond and the π*-LUMO of the Mn(V)₁=O₍₆₎ bond plays an important role for the concerted O–O bond formation for water oxidation in the CaMn₄O₆ cluster of OEC of PSII. One electron transfer (OET) from the π-HOMO of the Mn(V)₁=O₍₆₎ bond to the σ*-LUMO of the Mn(IV)₄–O₍₅₎ bond occurs for the formation of electron transfer diradical, where the generated anion radical [Mn(IV)₄–O₍₅₎]^-? part is relaxed to the ?Mn(III)₄?…?O₍₅₎^- structure and the cation radical [O₍₆₎=Mn(V)₁]⁺ ? part is relaxed to the ⁺O₍₆₎–Mn(IV)₁? structure because of the charge-spin separation for the electron-and hole-doped Mn–oxo bonds. Therefore, the local spins are responsible for the one-electron reductions of Mn(IV)₄->Mn(III)₄ and Mn(V)₁->Mn(IV)₁. On the other hand, the O₍₅₎^- and O₍₆₎⁺ sites generated undergo the O–O bond formation in the CaMn₄O₆ cluster. The Ca(II) ion in the cubane- skeleton of the CaMn₄O₆ cluster assists the above orbital interactions by the lowering of the orbital energy levels of π*-LUMO of Mn(V)₁=O₍₆₎ and σ*-LUMO of Mn(IV)₄–O₍₅₎, indicating an important role of its Lewis acidity. Present CBS mechanism for the O–O bond formation coupled with one electron reductions of the high-valent Mn ions is different from the conventional radical coupling (RC) and acid-base (AB) mechanisms for water oxidation in artificial and native photosynthesis systems. The proton-coupled electron transfer (PC-OET) mechanism for the O–O bond formation is also touched in relation to the CBS-OET mechanism.     

Preparation and Characterization of Activated Carbon from Microwave and Conventional Heated Almond Shells Using Phosphoric Acid Activation

Activated carbon production from almond shells using phosphoric acid activation agent was achieved by applying both conventional heating and microwave heating in succession. The morphology and surface properties of activated carbon were studied using thermogravimetric and differential gravimetric analysis, Fourier-transform infrared spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller analysis. A surface area of 1128 m²/g was achieved by optimizing the microwave power (500?W), microwave application time (15?minutes), conventional heating time (45?minutes), conventional heating temperature (500?°C), and the phosphoric acid:sample ratio (0.7:1). An adsorption capacity of methylene blue of 148?mg/g and an iodine value of 791?mg/g was obtained for the prepared activated carbon.     

原位液相透射电子显微镜及其在 纳米粒子表征方面的应用

近年来,基于透射电子显微技术、微纳加工技术和薄膜制造技术的发展,原位液相透射电子显微技术产生,为构建多种纳米级分辨率尺度下的微实验平台,发展新型纳米表征技术和众多领域的相关研究提供了途径.本文首先介绍了应用于原位液相透射电子显微技术的液体腔设计要求,然后介绍了液体腔的发展和典型的制备工艺,最后综述了近年来液体腔透射电子显微镜在纳米粒子成核和生长方面的应用研究,并探讨了该技术前沿发展面临的机遇和挑战.本文将为提高我国先进纳米表征技术和原子精准构筑技术提供相关讨论和支持.     

ZnO基薄膜晶体管的研究

ZnO是一种宽带隙的光电半导体材料,能应用于很多领域,如可用在压敏变阻器、声表面波器件、气敏元件、紫外光探测等。ZnO也可以作为有源层应用于薄膜晶体管(TFT)中。ZnO基薄膜晶体管具有以下突出优势:对于可见光部分平均具有80%以上的透射率,迁移率可以高达36cm2/V·s,开/关电流比大于106,可在较低温度(甚至室温)下制备。基于这些优点,ZnOTFT具有取代有源矩阵液晶显示器中常规a-SiTFT的趋势。同时对ZnOTFT的研究也推动了透明电子学的发展。本文阐述了ZnOTFT优越的电学性能,指出了其目前尚存在的不足,并对其发展前景进行了展望。     

扭臂式静电微驱动器的pulli-n现象分析

从扭臂式微驱动器模型出发,分析了器件在静电驱动条件下pulli-n现象的产生条件,并给出公式化结果。讨论了器件的几何结构参数对于pulli-n现象的影响,并对具体结构的器件给出了pulli-n角度和pulli-n电压等方面的分析结果。对于特定的扭臂结构,pulli-n角度为悬臂梁最大扭转角度的44.04%,且与扭臂的结构参数无关。     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。