Effect of sodium doping on graded Cu(In1−xGax)Se2 thin films prepared by chemical spray pyrolysis

In the present work we have studied the effect of Na on the properties of graded Cu(In_1−xGa_x)Se₂ (CIGS) layer. Graded CIGS structures were prepared by chemical spray pyrolysis at a substrate temperature of 350 °C on soda lime glass. Sodium chloride is used as a dopant along with metal (Cu/In/Ga) chlorides and n, n-dimethyl selenourea precursors. The addition of Na exhibited better crystallinity with chalcopyrite phase and an improvement in preferential orientation along the (112) plane. Energy dispersive analysis of X-rays (line/point mapping) revealed a graded nature of the film and percentage incorporation of Na (0.86 at%). Raman studies showed that the film without sodium doping consists of mixed phase of chalcopyrite and CuAu ordering. Influence of sodium showed a remarkable decrease in electrical resistivity (0.49–0.087 Ω cm) as well as an increase in carrier concentration (3.0×10¹⁸–2.5×10¹⁹ cm⁻³) compared to the un-doped films. As carrier concentration increased after sodium doping, the band gap shifted from 1.32 eV to 1.20 eV. Activation energies for un-doped and Na doped films from modified Arrhenius plot were calculated to be 0.49 eV and 0.20 eV, respectively. Extremely short carrier lifetimes in the CIGS thin films were measured by a novel, non-destructive, noncontact method (transmission modulated photoconductive decay). Minority carrier lifetimes of graded CIGS layers without and with external Na doping are found to be 3.0 and 5.6 ns, respectively.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

化学法改性煤沥青脱除苯并芘的研究

在管式反应器中采用苯甲酸、聚乙二醇、固体古马隆树脂（S）、液体古马隆树脂（L）为添加剂来降低煤沥青中有害物质苯并芘的含量，以期使得煤沥青可绿色化应用。采用紫外-可见分光光度计分析煤沥青中苯并芘含量。考察了反应温度、反应时间、添加剂添加量、催化剂等工艺条件对添加剂脱除煤沥青中苯并芘的影响。结果表明，不同工艺条件能降低煤沥青中苯并芘的含量。在优化条件下，不同添加剂对苯并芘脱除率由高到低依次为：液体古马隆树脂、聚乙二醇、苯甲酸和固体古马隆树脂。分析其反应机理，这与催化剂的酸性相关，发生亲电取代反应。结果表明，液体古马隆树脂（L）在催化剂存在下对煤沥青中苯并芘脱除率可达73.0%，显示了良好的应用前景。     

Thermally Crosslinkable and Chemically Modifiable Aromatic Polyesters Possessing Pendant Propargyloxy Groups

New aromatic (co)polyesters containing pendant propargyloxy groups were synthesized by phase transfer‐catalyzed interfacial polycondensation of 5‐(propargyloxy)isophthaloyl chloride (P‐IPC) and various compositions of P‐IPC and isophthaloyl chloride with bisphenol A. FTIR and NMR spectroscopic data, respectively, revealed successful incorporation of pendant propargyloxy groups into (co)polyesters and formation of (co)polyesters with desired compositions. (Co)polyesters exhibited good solubility in common organic solvents such as chloroform, dichloromethane, and tetrahydrofuran and could be cast into transparent, flexible, and tough films from chloroform solution. Inherent viscosities and number average molecular weights of (co)polyesters were in the range 0.77–1.33 dL/g and 43,600–118,000 g/mol, respectively, indicating the achievement of reasonably high‐molecular weights. The 10% weight loss temperatures of (co)polyesters were in the range 390–420 °C, demonstrating their good thermal stability. (Co)polyesters exhibited T_g in the range 146–170 °C and T_g values decreased with increase in mol % incorporation of P‐IPC. The study of non‐isothermal curing by DSC indicated thermal crosslinking of (co)polyesters via propargyloxy groups. The utility of pendant propargyloxy group was demonstrated by post‐modification of the selected copolyester with 1‐(4‐azidobutyl)pyrene, 9‐(azidomethyl)anthracene, and azido‐terminated poly(ethyleneglycol) monomethyl ether via copper(I)‐catalyzed Huisgen 1,3‐dipolar cycloaddition reaction. FTIR and ¹H NMR spectra confirmed that click reaction was quantitative. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 588–597     

Oxidative Epigallocatechin Gallate Coating on Polymeric Substrates for Bone Tissue Regeneration

Plant derived flavonoids have not been well explored in tissue engineering applications due to difficulties in efficient formulations with biomaterials for controlled presentation. Here, the authors report that surface coating of epigallocatechin gallate (EGCG) on polymeric substrates including poly (L‐lactic acid) (PLLA) nanofibers can be performed via oxidative polymerization of EGCG in the presence of cations, enabling regulation of biological functions of multiple cell types implicated in bone regeneration. EGCG coating on the PLLA nanofiber promotes osteogenic differentiation of adipose‐derived stem cells (ADSCs) and is potent to suppress adipogenesis of ADSCs while significantly reduces osteoclastic maturation of murine macrophages. Moreover, EGCG coating serves as a protective layer for ADSCs against oxidative stress caused by hydrogen peroxide. Finally, the in vivo implantation of EGCG‐coated nanofibers into a mouse calvarial defect model significantly promotes the bone regeneration (61.52 ± 28.10%) as compared to defect (17.48 ± 11.07%). Collectively, the results suggest that EGCG coating is a simple bioinspired surface modification of polymeric biomaterials and importantly can thus serve as a promising interface for tuning activities of multiple cell types associated with bone fracture healing.     

Enhancing the Water Stability of Al‐MIL‐101‐NH2 via Postsynthetic Modification

The resistance of metal–organic frameworks towards water is a very critical issue concerning their practical use. Recently, it was shown for microporous MOFs that the water stability could be increased by introducing hydrophobic pendant groups. Here, we demonstrate a remarkable stabilisation of the mesoporous MOF Al‐MIL‐101‐NH₂ by postsynthetic modification with phenyl isocyanate. In this process 86 % of the amino groups were converted into phenylurea units. As a consequence, the long‐term stability of Al‐MIL‐101‐URPh in liquid water could be extended beyond a week. In water saturated atmospheres Al‐MIL‐101‐URPh decomposed at least 12‐times slower than the unfunctionalised analogue. To study the underlying processes both materials were characterised by Ar, N₂ and H₂O sorption measurements, powder X‐ray diffraction, thermogravimetric and chemical analysis as well as solid‐state NMR and IR spectroscopy. Postsynthetic modification decreased the BET equivalent surface area from 3363 to 1555 m² g^?1 for Al‐MIL‐101‐URPh and reduced the mean diameters of the mesopores by 0.6 nm without degrading the structure significantly and reducing thermal stability. In spite of similar water uptake capacities, the relative humidity‐dependent uptake of Al‐MIL‐101‐URPh is slowed and occurs at higher relative humidity values. In combination with ¹H‐²⁷Al D ‐HMQC NMR spectroscopy experiments this favours a shielding mechanism of the Al clusters by the pendant phenyl groups and rules out pore blocking.     

Mg_(0.15)Zn_(0.85)O:Tb合金薄膜的阴极射线发光性质研究

采用溶胶凝胶方法成功地制备了掺杂稀土铽离子的 Zn O和 Mg0 .1 5Zn0 .85薄膜。通过对 X射线衍射结果的分析表明 ,稀土离子替代了 Zn2 +的格位 ,进入了半导体基质的晶格中。从阴极射线发光结果可以发现 ,在Mg0 .1 5Zn0 .85O基质中 ,可以观察到来源于稀土铽离子各能级的发射 ,而 Zn O:Tb的薄膜只能观察到较强的铽离子 5D4 — 7F5能级的跃迁。这可能是由于 Mg0 .1 5Zn0 .85O基质的能隙 (3 .65 e V)比 Zn O更宽 (3 .3 e V) ,其对铽离子的能量传递更有效的缘故。     

Facile modifications of a polyimide via chloromethylation. I. Novel synthesis of a new photosensitive polyimide

A soluble aromatic polyimide was chloromethylated via a reaction with chloromethyl methyl ether in the presence of tin(IV) chloride to produce a new starting material for the modification of aromatic polyimides. The chemical structure of the resulting polymer was confirmed by ¹H NMR and Fourier transform infrared spectroscopy. The maximum number of chloromethyl groups per repeat unit was 1.81. The chloromethylated polyimide was stable up to 250 °C and soluble in both chloroform and tetrahydrofuran. So that its utilization for further modification could be demonstrated, cinnamic acid was reacted with the formed polyimide, and it produced a new photosensitive polyimide with a cinnamoyl side chain. The photosensitivity of the resulting polyimide was investigated with ultraviolet spectroscopic methods. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 22–29, 2003     

Photochemical attachment of polymers on planar surfaces with a covalently anchored monolayer of a novel naphthyl ketone photochemical radical generator

A monolayer of covalently anchored, novel, binaphthyl ketone is used as a surface‐confined photochemical radical generator (PRG) for anchoring a variety of polymers to silicon surfaces. The precursor PRG is synthesized by the application of a facile and novel method for the oxidation of sterically hindered benzylic hydrocarbons to carbonyl compounds. Oxidation was carried out with a stoichiometric amount of potassium peroxydisulfate, in the presence of a catalytic amount of copper sulfate in an acetonitrile/water mixture. The PRG synthesized is characterized by ¹H NMR, UV, and Fourier transform infrared (FTIR). The covalently attached monolayers are characterized by X‐ray photoelectron spectroscopy, ellipsometry, and water contact angle measurements. The method developed is applicable to the preparation of a monolayer of a variety of polymers on a wide range of substrates carrying surface hydroxyl groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5413–5423, 2004