Effect of sodium doping on graded Cu(In1−xGax)Se2 thin films prepared by chemical spray pyrolysis

In the present work we have studied the effect of Na on the properties of graded Cu(In_1−xGa_x)Se₂ (CIGS) layer. Graded CIGS structures were prepared by chemical spray pyrolysis at a substrate temperature of 350 °C on soda lime glass. Sodium chloride is used as a dopant along with metal (Cu/In/Ga) chlorides and n, n-dimethyl selenourea precursors. The addition of Na exhibited better crystallinity with chalcopyrite phase and an improvement in preferential orientation along the (112) plane. Energy dispersive analysis of X-rays (line/point mapping) revealed a graded nature of the film and percentage incorporation of Na (0.86 at%). Raman studies showed that the film without sodium doping consists of mixed phase of chalcopyrite and CuAu ordering. Influence of sodium showed a remarkable decrease in electrical resistivity (0.49–0.087 Ω cm) as well as an increase in carrier concentration (3.0×10¹⁸–2.5×10¹⁹ cm⁻³) compared to the un-doped films. As carrier concentration increased after sodium doping, the band gap shifted from 1.32 eV to 1.20 eV. Activation energies for un-doped and Na doped films from modified Arrhenius plot were calculated to be 0.49 eV and 0.20 eV, respectively. Extremely short carrier lifetimes in the CIGS thin films were measured by a novel, non-destructive, noncontact method (transmission modulated photoconductive decay). Minority carrier lifetimes of graded CIGS layers without and with external Na doping are found to be 3.0 and 5.6 ns, respectively.     

机载光电雷达它机试飞技术研究

机载光电雷达受平台及大气环境影响较大,而它机试飞能有效规避研制风险,是产品研制的必经阶段。本文介绍了机载光电雷达它机试飞试验系统组成、试验流程和数据处理等内容。经工程验证,实施过程满足任务需求,对其他光电系统的它机及本机试飞具有参考价值。     

Charge injection in metal/organic/metal structures with ZnO:Al/organic interface modified by Zn1−xMgxO:Al layer

Aluminum-doped zinc oxide (ZnO:Al, AZO) electrodes were covered with very thin (∼6 nm) Zn_1−xMg_xO:Al (AMZO) layers grown by atomic layer deposition. They were tested as hole blocking/electron injecting contacts to organic semiconductors. Depending on the ALD growth conditions, the magnesium content at the film surface varied from x = 0 to x = 0.6. Magnesium was present only at the ZnO:Al surface and subsurface regions and did not diffuse into deeper parts of the layer. The work function of the AZO/AMZO (x = 0.3) film was 3.4 eV (based on the ultraviolet photoelectron spectroscopy). To investigate carrier injection properties of such contacts, single layer organic structures with either pentacene or 2,4-bis[4-(N,N-diisobutylamino)-2,6-dihydroxyphenyl] squaraine layers were prepared. Deposition of the AMZO layers with x = 0.3 resulted in a decrease of the reverse currents by 1–2 orders of magnitude and an improvement of the diode rectification. The AMZO layer improved hole blocking/electron injecting properties of the AZO electrodes. The analysis of the current-voltage characteristics by a differential approach revealed a richer injection and recombination mechanisms in the structures containing the additional AMZO layer. Among those mechanisms, monomolecular, bimolecular and superhigh injection were identified.     

Definition and detection of data-based uniqueness in evaluating bilinear (two-way) chemical measurements

Multivariate curve resolution methods, frequently used in analyzing bilinear data sets, result in ambiguous decomposition in general. Implementing the adequate constraints may lead to reduce the so-called rotational ambiguity drastically, and in the most favorable cases to the unique solution. However, in some special cases, non-negativity constraint as minimal information of the system is a sufficient condition to resolve profiles uniquely. Although, several studies on exploring the uniqueness of the bilinear non-negatively constrained multivariate curve resolution methods have been made in the literature, it has still remained a mysterious question. In 1995, Manne published his profile-based theorems giving the necessary and sufficient conditions of the unique resolution. In this study, a new term, i.e., data-based uniqueness is defined and investigated in details, and a general procedure is suggested for detection of uniquely recovered profile(s) on the basis of data set structure in the abstract space. Close inspection of Borgen plots of these data sets leads to realize the comprehensive information of local rank, and these argumentations furnish a basis for data-based uniqueness theorem. The reported phenomenon and its exploration is a new stage (it can be said fundament) in understanding and describing the bilinear (matrix-type) chemical data in general.     

Fully solution-processed and multilayer blue organic light-emitting diodes based on efficient small molecule emissive layer and intergrated interlayer optimization

Efficient and fully solution-processed blue organic light-emitting diodes (OLEDs) based on fluorescent small-molecule and methanol/water soluble conjugated polymer as electron-injection material are reported. The emitting layer is 3,6-bis(9,9,9′,9′-tetrakis (6-(9H-carbazol-9-yl)hexyl)-9H,9′H-[2,2′-bifluoren]-7-yl)dib-nzo[b, d]thiophene 5, 5-dioxide (OCSoC) with a blue-fluorescent small-molecule, and a methanol/water soluble polymer poly[(9,9-bis(30-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl-fluorene)] (PFN) acted as electron-injection layer (EIL). All the organic layers are spin-coated from solution. The multilayer device structure with emitting layer/electron-injection layer is achieved by solution-processed method without the dissolution problem between layers. The performances of the devices show that the maximum luminous efficiency of the multilayer device is increased about 43%, compared to the single-layer device. PFN acting as the EIL material plays a key role in the improvement of the device performance when used in solution-processed small-molecule OLEDs.     

Enhancing signal-to-noise ratio and resolution in low-field NMR relaxation measurements using post-acquisition digital filters

The traditional way to enhance signal-to-noise ratio (SNR) of nuclear magnetic resonance (NMR) signals is to increase the number of scans. However, this procedure increases the measuring time that can be prohibitive for some applications. Therefore, we have tested the use of several post-acquisition digital filters to enhance SNR up to one order of magnitude in time domain NMR (TD-NMR) relaxation measurements. The procedures were studied using continuous wave free precession (CWFP-T₁) signals, acquired with very low flip angles that contain six times more noise than the Carr–Purcell–Meiboom–Gill (CPMG) signal of the same sample and experimental time. Linear (LI) and logarithmic (LO) data compression, low-pass infinity impulse response (LP), Savitzky–Golay (SG), and wavelet transform (WA) post-acquisition filters enhanced the SNR of the CWFP-T₁ signals by at least six times. The best filters were LO, SG, and WA that have high enhancement in SNR without significant distortions in the ILT relaxation distribution data. Therefore, it was demonstrated that these post-acquisition digital filters could be a useful way to denoise CWFP-T₁, as well as CPMG noisy signals, and consequently reducing the experimental time. It was also demonstrated that filtered CWFP-T₁ method has the potential to be a rapid and nondestructive method to measure fat content in beef and certainly in other meat samples.     

The visible and ultraviolet organic light-emitting diodes with germanium dioxide as facile solution-processed anode buffer layer

Germanium dioxide (GeO₂) aqueous solutions are facilely prepared and the corresponding anode buffer layers (ABLs) with solution process are demonstrated. Atomic force microscopy, X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy measurements show that solution-processed GeO₂ behaves superior film morphology and enhanced work function. Using GeO₂ as ABL of organic light-emitting diodes (OLEDs), the visible device with tris(8-hydroxy-quinolinato)aluminium as emitter gives maximum luminous efficiency of 6.5 cd/A and power efficiency of 3.5 lm/W, the ultraviolet device with 3-(4-biphenyl)-4-phenyl-5-tert-butylphenyl-1,2,4-triazole as emitter exhibits short-wavelength emission with peak of 376 nm, full-width at half-maximum of 42 nm, maximum radiance of 3.36 mW/cm² and external quantum efficiency of 1.5%. The performances are almost comparable to the counterparts with poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) as ABL. The current, impedance, phase and capacitance as a function of voltage characteristics elucidate that the GeO₂ ABL formed from appropriate concentration of GeO₂ aqueous solution favors hole injection enhancement and accordingly promoting device performance.     

焦炉上升管内壁结焦炭层的光谱学分析及结焦机理研究

以焦炉上升管内壁结焦炭层块为研究对象，采用X射线荧光光谱仪（XRF）、X射线衍射仪（XRD）、傅里叶红外光谱仪（FTIR）和激光共聚焦拉曼光谱仪（Raman）对结焦炭层的元素组成，以及各结焦炭层的矿物组成、组成结构和分子结构进行测试。分析从结焦炭层块外表面向内表面过渡的各结焦炭层的差异性，揭示焦炉上升管内壁结焦机理。结果表明焦炉上升管内粉尘中Fe，S和Cr极易催化荒煤气中蒽、萘等稠环芳烃化合物成炭，在焦炉上升管内壁形成炭颗粒沉积，为焦油凝结挂壁提供载体，在荒煤气温度降至结焦温度时易结焦积碳。结焦炭层均含有芳香层结构，随着结焦炭层从外表面向内表面过渡，各结焦炭层的面层间距(d₀₀₂)逐渐降低、层片直径(L_a)先降低后增加、层片堆砌高度(Lc)和芳香层数(N)先稳定后增加。结焦炭层石墨化过程是由结焦炭层内表面向外表面进行，主要包括其片层外缘的羧基和部分C-O结构的降解剥离，从而形成高度规整的共轭结构。结焦炭层块中C元素是以结晶碳与无定型碳的混合物形式存在。以上研究为解决焦炉上升管内壁结焦及腐蚀问题，提高换热器换热效率，有效回收焦炉荒煤气显热，降低焦化企业能耗提供实验基础和理论依据。     

Effective Location Based Services with Dynamic Data Management in Mobile Environments

With the proliferation of mobile computing technologies, location based services have been identified as one of the most promising target application. We classify mobile information service domains based on feature characteristics of the information sources and different patterns of mobile information access. By carefully examining the service requirements, we identify the dynamic data management problem that must be addressed for effective location based services in mobile environments. We then devise a general architecture and cost model for servicing both location independent and location dependent data. Based on the architecture and cost model, we propose a set of dynamic data management strategies that employs judicious caching, proactive server pushing and neighborhood replication to reduce service cost and improve response time under changing user mobility and access patterns. Detail behavior analysis helps us in precisely capturing when and how to apply these strategies. Simulation results suggest that different strategies are effective for different types of data in response to different patterns of movement and information access. Shiow-yang Wu is an associate professor of the Department of Computer Science and Information Engineering at National Dong Hwa University, Hualien, Taiwan, R.O.C. He received the BS and MS degrees in computer engineering from National Chiao Tung University, Hsinchu, Taiwan, ROC, and the PhD degree in computer science from the University of Texas at Austin in 1984, 1986, and 1995, respectively. His research interests include data/knowledge bases, mobile computing, distributed processing, intelligence information systems, and electronic commerce. Kun-Ta Wu was born in Taipei, Taiwan, R.O.C., in 1976. He received the B.S. degree in computer science from Soochow University, Taipei, Taiwan, R.O.C., in 1999 and the M.S. degree in computer science and information engineering from National Dong Hwa University, Hualien, Taiwan, R.O.C., in 2001. Currently, he is an Assistant Researcher in the Domestic Division at Science and Technology Information Center, National Science Council, R.O.C., as a member of Information Gathering and Analysis Group of National Information and Communication Security Taskforce. His research interests include mobile computing, wireless network and information security.     

Uplink Scheduling in CDMA Packet-Data Systems

Uplink scheduling in wireless systems is gaining importance due to arising uplink intensive data services (ftp, image uploads etc.), which could be hampered by the currently in-built asymmetry in favor of the downlink. In this work, we propose and study algorithms for efficient uplink packet-data scheduling in a CDMA cell. The algorithms attempt to maximize system throughput under transmit power limitations on the mobiles assuming instantaneous knowledge of user queues and channels. However no channel statistics or traffic characterization is necessary. Apart from increasing throughput, the algorithms also improve fairness of service among users, hence reducing chances of buffer overflows for poorly located users. The major observation arising from our analysis is that it is advantageous on the uplink to schedule “strong” users one-at-a-time, and “weak” users in larger groups. This contrasts with the downlink where one-at-a-time transmission for all users has shown to be the preferred mode in much previous work. Based on the optimal schedules, we propose less complex and more practical approximate methods, both of which offer significant performance improvement compared to one-at-a-time transmission, and the widely acclaimed Proportional Fair (PF) algorithm, in simulations. When queue content cannot be fed back, we propose a simple modification of PF, Uplink PF (UPF), that offers similar improvement. Hereafter, we refer to users with low recieved power at the base even when transmitting at peak transmit power as “weak” users, and the strongly recieved users at the base as “strong” users. Krishnan Kumaran is currently a member of the Complex Systems Modeling section in the Corporate Strategic Research of ExxonMobil Corp., Clinton, NJ. Formerly, he was a Member of Technical Staff in the Mathematics of Networks and Systems Research Department at Bell Labs in Murray Hill, NJ, where his research interests were in modeling, analysis and simulation of design, resource management and scheduling issues in telecommunication networks. Lijun Qian is an assistant professor in the Department of Electrical Engineering at Prairie View A&M University. He received his B.S. from Tsinghua University in Beijing, M.S. from Technion-Israel Institute of Technology, and Ph.D. from WINLAB, Rutgers University, all in electrical engineering. Before joining PVAMU, he was a researcher at Networks and Systems Research Department of Bell Labs in Murray Hill, NJ. His major research interests are in wireless communications and networking technologies, especially in radio resource management, protocol design, TCP/RLP optimization and MPLS traffic engineering.