Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

等离子体刻蚀工艺控制模型分析

讨论了主因素分析法以及神经网络法在等离子体刻蚀工艺中的应用.结果表明主元素分析法可以实现对数据的压缩,而神经网络算法则显示出比传统的统计过程控制算法更好的准确性.     

Imprint lithography of pyramidal photonic pillars using hydrazine etching

An inexpensive method to produce a pyramidal-type 2D photonic structures in the silicon substrate was proposed. The method is based on the combination of imprint lithography and wet Si1 0 0 etching in water solution of hydrazine, which etches 1 1 1 faces much more slowly than others. Thermally grown SiO₂ mask for the hydrazine etching was used, because single Al mask cannot be well bonded to the substrate and tends to peel during the etching. It was revealed that transmittance in the infrared spectrum region of the patterned silicon decreases by about five times compared with that of flat silicon substrate and this decrease is almost independent of the angle of the incident beam. In the infrared region, decrease of transmittance of the patterned samples is directly proportional to the wave number. The shape of formed pyramids has strong influence on the transmittance. Decrease of the transmittance is much more rapid and larger in the case of sharpless pillars.     

Strain hardening of polycarbonate in the glassy state: Influence of temperature and molecular weight

This study is concerned with the temperature and molecular weight dependence of the strain-hardening behavior of polycarbonate. It is shown that the strain-hardening modulus reduces with increasing temperature and decreasing molecular weight. This result is interpreted in terms of temperature accelerated relaxation of the entanglement network. Moreover, it is shown that frozen-in orientations, induced by homogeneous deformations above the glass transition temperature, lead to anisotropic yield behavior that can be fully rationalized (and modelled) in terms of a superimposed stress contribution of the prestrained network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2041–2049, 2004     

Artificial boundary conditions for Petrovsky systems of second order in exterior domains and in other domains of conical type

The approximation of solutions to boundary value problems on unbounded domains by those on bounded domains is one of the main applications for artificial boundary conditions. Based on asymptotic analysis, here a new method is presented to construct local artificial boundary conditions for a very general class of elliptic problems where the main asymptotic term is not known explicitly. Existence and uniqueness of approximating solutions are proved together with asymptotically precise error estimates. One class of important examples includes boundary value problems for anisotropic elasticity and piezoelectricity. Copyright © 2004 John Wiley & Sons, Ltd.     

Inductively coupled plasma etching of InGaP, AllnP, and AlGaP in Cl2 and BCl3 chemistries

Dry etching of InGaP, AlInP, and AlGaP in inductively coupled plasmas (ICP) is reported as a function of plasma chemistry (BCl₃ or Cl₂, with additives of Ar, N₂, or H₂), source power, radio frequency chuck power, and pressure. Smooth anisotropic pattern transfer at peak etch rates of 1000–2000Å·min^?1 is obtained at low DC self-biases (?100V dc) and pressures (2 mTorr). The etch mechanism is characterized by a trade-off between supplying sufficient active chloride species to the surface to produce a strong chemical enhancement of the etch rate, and the efficient removal of the chlorinated etch products before a thick selvedge layer is formed. Cl₂ produces smooth surfaces over a wider range of conditions than does BCl₃.     

低压铝箔交流腐蚀研究

在３０Ｈｚ频率下，通过铝箔在ＨＣｌ＋Ｈ２ＳＯ４＋ＨＮＯ３＋Ｈ３ＰＯ４体系中的交流腐蚀，研究腐蚀液组成中腐蚀主体及缓蚀剂对铝箔腐蚀的作用，探讨腐蚀过程中电源频率、腐蚀液温度、电流密度及腐蚀时间对铝箔腐蚀的影响。腐蚀液组成的配比恰当，有利于比容的提高。在特定的频率下采用合适的腐蚀液温度、适宜的电流密度和腐蚀时间可以提高铝箔的静电容量。     

High-density plasma etching of indium-zinc oxide films in Ar/Cl2 and Ar/CH4/H2 chemistries

The dry etching characteristics of transparent and conductive indium-zinc oxide (IZO) films have been investigated using an inductively coupled high-density plasma. While the Cl₂-based plasma mixture showed little enhancement over physical sputtering in a pure argon atmosphere, the CH₄/H₂/Ar chemistry produced an increase of the IZO etch rate. On the other hand, the surface morphology of IZO films after etching in Ar and Ar/Cl₂ discharges is smooth, whereas that after etching in CH₄/H₂/Ar presents particle-like features resulting from the preferential desorption of In- and O-containing products. Etching in CH₄/H₂/Ar also produces formation of a Zn-rich surface layer, whose thickness (∼40 nm) is well-above the expected range of incident ions in the material (∼1 nm). Such alteration of the IZO layer after etching in CH₄/H₂/Ar plasmas is expected to have a significant impact on the transparent electrode properties in optoelectronic device fabrication.     

Ultrasonic evaluation of anisotropic damage in multiaxially textile-reinforced thermoplastic composites made from hybrid yarns

The basic damage and failure models of multiaxially reinforced composites with a thermoplastic matrix are presented and verified. Within the framework of continuum damage mechanics, a phenomenological model is introduced, where the damage is defined as a change in the elasticity tensor. For damage identification, a specific ultrasonic device was developed. A combination of an immersion set-up and a contact coupling device formed a system for an efficient determination of stiffness-tensor components from convenient sets of velocity measurements. Linked to a tensile machine, it allowed us to measure the anisotropic damage of the new materials group caused by tensile loading. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 2, pp. 221–234, March–April, 2006.