Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

雕刻技术的研制和应用

在对铝合金铸件进行X射线实时探伤时，由于采集回来的许多图像的目标物体的轮廓比较模糊，这样在评片时容易造成对铸件的误判和漏判。针对这种现象并结合这类图像噪声源多的特点，在研究常用卷积算法的基础上，采用特殊卷积（特殊的卷积核）操作，同时根据雕刻的艺术底色为灰色，最后给卷积结果加上灰度值128，实验结果表明图像中目标物体的轮廓变得更清楚，同时处理后的图像具有比较好的三维效果，这给工作人员在看图时带来了方便。     

固体铝电解电容器用导电高分子制备工艺进展

依据近年的相关专利,综述了用于固体铝电解电容器的导电高分子的最新制备工艺,介绍了导电高分子固体铝电解电容器的结构,详细描述了制备导电高分子的两种主要方法——化学聚合和电化学聚合——及其进展历程。介绍了新颖掺杂剂的发现与使用,对各种工艺的特点进行了评述。     

超高压大容量铝电解电容器的研制

分析了大功率设备用超高压大容量铝电解电容器的特点,通过研制工作电解液、制订制作工艺及零部件设计方案,研制出的超高压大容量铝电解电容器具有损耗角正切小(tgδ为0.25)、承受纹波电流能力强(100 Hz,2.12～27.8 A)及寿命长的特点,耐久性达到85℃,5 000 h。     

铝薄膜CMP影响因素分析

提出了在碱性抛光液中铝薄膜化学机械抛光的机理模型,对抛光液的pH值、磨料、氧化剂浓度对过程参数的影响做了一些试验分析。试验结果表面粗糙度的铝薄膜所需的最优化CMP过程参数:硅溶胶粒径为15～20nm,pH值为10.8～11.2,氧化剂浓度为2.5%～3%。     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

镍铬合金在酸性CuCl2溶液中反应机理

对铜在酸性CuCl_2溶液中蚀刻反应机理论述,利用氧化-还原电动势原理,详细论述了Ni80Cr20合金在酸性CuCl_2溶液中化学蚀刻反应机理,以及影响蚀刻速度的因素,并对溶液中金属离子的存在形式作了验证。     

Characterization of ZnO:AI films deposited by r.f.magnetron-sputtering at low temperature

Transparent conducting ZnO:AI thin films with good adhesion and Iow resistivity have been prepared on organic substrates and Coming 7059 glass substrates by r.f. magnetron-sputtering technique at Iow substrate temperature (25-210℃). Structural and photoelectric properties of the deposited films are investigated. The deposited films are polycrystalline with hexagonal structure and a preferred orientation with the c-axis perpendicular to the substrate. Only the (002) peak is observed.High quality films with resistivity as Iow as 1.0 x 10- 3Ω@ cm and 8.4 x 10- 4Ω@ cm, the average transmittance over 74% and 85% in the wavelength range of the visible spectrum have been obtained on different substrates.     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。