Study of the pulsed laser vapor doping of Si(1 0 0) with KrF excimer laser and BCl3 gas

The properties of pulsed laser vapor doping on p-Si(1 0 0) with a KrF (248 nm) excimer pulsed laser (248 nm) and BCl₃ gas are reported in this paper. The doped samples are characterized by the resistance measured using a four-probe method, since the sheet resistance changes with the carrier concentration of the sample. The doping effects with the variation of laser energy density, pulse number, and the pressure of BCl₃ were investigated in terms of the sheet resistance. In this way, the optimized parameters were obtained and used for the positive heavy doping on p-Si(1 0 0) and p-Si(1 1 1). Then, using a square mesh under the above conditions, an image doping was completed. Finally, the metal–semiconductor Ohmic contacts were realized by plating Ag and Cu films on the doped surface.     

Time resolved laser-induced plasma dynamics

The structure and evolution of the laser-induced vapor plume and shockwave were measured from femtosecond time resolved shadowgraph images. By changing the wavelength of the probe beam (400 and 800 nm), differences in the opacity of the vapor plume were measured as a function of delay time from the ablation laser pulse. The evolution of the temperature and electron number density during and after the ablation laser pulse were determined and compared for ablation in argon and helium background gases. A laser supported detonation wave (LSD) observed for ablation in argon, blocks the incoming laser energy and generates a high-pressure region above the vapor plume.     

一种甲醇直接气相羰基化新催化剂

本世纪７０年代Ｍｏｎｓａｎｔｏ公司成功开发了甲醇液相羰化ＲｈＩ催化体系，使甲醇羰化生产醋酸成为重要的工业过程．然而，由于此工艺产物与催化剂分离复杂、铑资源紧缺以及体系中还必须加大量的碘甲烷（或氢碘酸）作促进剂，设备腐蚀严重．８０年代以来，甲醇气相羰...     

Splitless injection of up to hundreds of microliters of liquid samples in capillary GC: Part II,experimental results

Sample evaporation in splitless injection of large volumes is rapid: depending on the experiment, results indicate that 200 μl of hexane, for instance, evaporates in 2–10 s, producing vapor at a rate of many hundreds of milliliters per minute. A 60 × 4 mm packed bed of 20–35 mesh Tenax TA enabled injection of 200 μl volumes of all solvents tested, and even 1 ml injections were possible provided they were performed over a period of 30 s. Retention of volatile sample components depends on the sample solvent, the injection volume, and the injection speed, but only little on the injector temperature. Losses of n-tridecane varied from hardly 15 % (when dissolved in pentane) to ca 60 % (ethyl acetate); losses of n-heptadecane were usually below 20 %. The column temperature during injection should be at least ca 20–30°C above the standard solvent boiling point.     

Vapor pressure measurement for water,methanol, ethanol,and their binary mixtures in the presence of an ionic liquid 1-ethyl-3-methylimidazolium dimethylphosphate

Vapor pressure data were measured for water, methanol and ethanol as well as their binary mixtures with an ionic liquid (IL) 1-ethyl-3-methylimidazolium dimethylphosphate ([EMIM][DMP]) at varying temperature and IL-content ranging from mass fraction of 0.10–0.70 by a quasi-static method. The vapor pressure data for the IL-containing binary systems were correlated using NRTL equation with average absolute relative deviation (ARD) within 0.0076, and the binary NRTL parameters was used for predicting the vapor pressure of the IL-containing ternary systems with reasonable accuracy. In addition, the infinite activity coefficients of solvents in [EMIM][DMP] and isobaric vapor–liquid equilibrium for IL-containing ternary systems at 101.325 kPa and mass fraction of IL being 0.5 were predicted with the regressed NRTL parameters. The results indicate that ionic liquid [EMIM][DMP] can depress the volatility of the solvents of water, methanol and ethanol but to a varying degree, leading to the variation of relative volatility of a solvent and even removal of azeotrope for water–ethanol mixture.     

Pure Organic Phase Phenol Biosensor Based on Tyrosinase Entrapped in a Vapor Deposited Titania Sol‐Gel Membrane

A novel amperometric biosensor was constructed for the determination of phenols in pure organic phase. This biosensor was fabricated by immobilizing tyrosinase in a titania sol‐gel membrane which was obtained with a vapor deposition method. This method was facile and avoided the calcination step needed in conventional titania sol‐gel process. The titania sol‐gel membrane could effectively retain the essential water layer around the enzyme molecule needed for maintaining its activity in organic phase. The experimental parameters such as solvent and operating potential were optimized. At ?100 mV this biosensor showed a good amperometric response to phenols in pure chloroform without any mediator and rehydration of the enzyme. For catechol determination the sensor exhibited a fast response of less than 5 seconds. The sensitivity of different phenols was as follows: catechol > phenol > p‐cresol. Additionally, the apparent Michaelis‐Menten constants of the encapsulated tyrosinase to catechol, phenol and p‐cresol were found to be 0.15±0.003, 0.17±0.008 and 0.21±0.004 mM, respectively. The biosensor had also good reproducibility and stability. This work provided a promising platform for the construction of pure organic phase biosensors and the determination of substrates with poor water solubility.     

Formation of Ad-Layers and Clusters on Condensation of Metal Vapors on Solid Surfaces

Synthesis of organometallic materials can be accomplished in many cases by cocondensation of metal atoms and organic molecules at low temperatures. The reaction kinetics is determined by the competition between metal cluster growth and formation of the organometallic compound. Interesting compounds may contain one or more metal atoms; the latter type could be obtained by reaction between a cluster containing the desired number of metal atoms and an organic molecule. A precise knowledge of the events occurring on condensation of metal atoms and cluster formation can therefore be of value in the control of chemical synthesis. These phenomena have been investigated in connection with the study of the growth of thin metallic films, both experimentally and theoretically. Direct observation of the formation of very small clusters is difficult. The good agreement between experimental results and recent calculations for the development of large clusters, however, allows reliable theoretical conclusions for the first stages of adsorption and cluster formation. The present contribution describes experimental work on film growth and relevant theoretical concepts, and an attempt is made to develop applications to organometallic synthesis.     

Tetraalkylammonium bromides in methanol: Small angle neutron scattering and vapor pressure measurements

Vapor pressure measurements and small angle scattering (SANS) experiments are reported and discussed for bispiperidinium (BP) bromide and n-tetrapentylammonium bromide solutions in methanol at 25°C. The BP⁺ ion which may be considered as a tetraalkylammonium (TAA) ion with pairwise connected alkyl chains, is used for the study of the effects due to flexible TAA alkyl chains. SANS intensities are calibrated with the help of the precise osmotic coefficients from the vapor pressure measurements.     

Surface patterns of block copolymers in thin layers after vapor treatment

A systematic study of formation of surface patterns in block copolymer thin layers after their exposure to solvent vapors was performed. The studied effect involves layers of thickness approximately equal to the ordering size of polymers - about 45 nm. Experiments were performed on three styrene - methacrylate derivative block copolymers, synthesized by living anionic polymerization: poly(4-octylstyrene)-block-poly(butyl methacrylate), poly(4-fluorostyrene)-block-poly(butyl methacrylate) and poly(p-octylstyrene)-block-poly(methyl methacrylate). The polymers were exposed to vapors of chloroform, 1,4-dioxane, hexane, acetone and tetrahydrofuran.     

Comparison between the pervaporation and vapor permeation performances of polycarbonate membranes

The pervaporation and vapor permeation performance of symmetrical and asymmetrical polycarbonate membranes, prepared via a dry-phase inversion and wet-phase inversion methods, respectively, were studied by measuring the permeation rate and separation factor. It was found that the polymer concentration effect on the pervaporation performance for the symmetrical polycarbonate membrane was lower than that for the asymmetrical polycarbonate membrane. Compared with pervaporation, vapor permeation has a significantly increased separation factor with a decreased permeation rate for the symmetrical polycarbonate membrane. Water molecules preferentially dissolve into the symmetrical polycarbonate membrane and diffuse easily through the membrane.